User Manual User Manual 0504
en Usage
en Usage
Please check all the parts are completed.
Connect the diuser
1. Place the diuser at a stable horizontal position. Connect the adapter to the DC
port at the bottom (Very important: do not connect the adapter to the AC power
source atthis moment) and
2. Remove the outer cover and the water tank cover
3. Add the puried water into the water tank. The water level is 50ml (min) ~ 200ml
(max)
4. Put the aroma into the water tank. It is suggested to put 5~8 drops for 200ml
water.
5. Replace the watertank cover and outer cover.
6. Connect adapter to the AC power source and start it.
Start to use
1. Press “ “, the diuser is in standby mode, the LED under the power button will
be on.
2. Press “ “, the diuser start to mist continuously, the LED “ “ wiII be in blue;
press this button again, the diuser will mist intermittently, the LED “ “ will be in
blue; pressthe button again , it will stop misting.
3. Press “ “, the atmosphere light is on, the colors change in series; press the
button again, the atmosphere will stay in current color; press the button again,
the atmosphere light will be o.
4. While the diuser is misting, press “ “, the timer will start, and the LED “1h“ will
be on. The default timer is 1 hour, which the diuser will be power on one hour;
press the button again, the timer is set to 3 hours, press the button again, it will
be set to 5 hours; press the button again, the timer will stop working.
Note: The would be some condenser water blocked the mist-outlet aer long time use; Please clean
the mist-outlet and continue to use.
Attention: DO NOTopen the outer cover or ll water/aroma while misting. It must be power o when
you ll the water and aroma.
Play the music
Start the bluetooth function on mobile phone or computer to play the Music.
1. Press the “ “ key to start the bluetooth, the LED “ “ will shine.
2. Start the bluetooth function on the mobile phone or computer, nd the name
“Aroma Diuser” , click it. Devices will match successfully with a response sound
and the LED light will be on.
3. Play the music on your mobile phone or computer, the music will be played
through the diuser audio at the same time.
Cleaning
For safety, it is suggested to clean the diuser regularly. Cleaning interval is 9~10times
of usage or 5-6 days. The clean procedures are as follow:
1. Disconnect the adaptor from the AC power source or turn o the power sources.
2. Place the diuser on a at and stable place such as table. Remove the outer
cover and the water tank cover. Assure that the place is at and stable to avoid
the water leakage.
3. When pouring out the water, keep the air-outlet up. Don’ t let any water ow
inside the PCB.
4. Clean the ultrasonic vibration plate atthe bottom ohe water tank with the cotton
bud; clean the outer cover with cloth or cotton bud.
5. It is suggested to run sterilization every 2-3 days.
6. When there is dirt like aroma or oil at the cover ohe diuser or the watertank,
please clean it by the dried cloth with kitchen diluents and warm water.
7. Aer complete the cleaning, please add the puried water into water tank, then
power on the diuserfor 30 minutes, drain the water out and dry the watertank.
You can storage the diuser aer it is dried out.
8. When there is dirt on the mist-outlet, please remove the outer cover, clean it with
the neutral detergent. Aer it is dried, you can use diuser again.
Note: When there is no feedback function or the diuser is crash, please disconnect the adapter from
the power source for a while. Then reconnect the adapter and restart the diuser.
Attention: You must use the neutral detergent to clean. Any detergent of chlorine, acid, enzyme le
inside the tank would produce hazard material and harmful to human.
