Armstrong 3031S Manual de instrucciones

Model No. q Model 320

q Model 320D

Serial No. :

Ship Date :

Model 320

Installation and Maintenance

Water Temperature Controls

Groups of Fixtures - Thermostatic

Keep this manual with installation for

future reference.

Armstrong International

221 Armstrong Blvd., Three Rivers, Michigan, 49093 - USA

armstronginternational.com/brain

Introduction.............................................................. 3

Specications .......................................................... 5

General Advisory ..................................................... 5

Safety ...................................................................... 6

Pack Contents ......................................................... 7

Schematic Piping..................................................... 8

Installation ............................................................... 9

General................................................................ 9

Installation Requirements.................................... 9

Tools Required .................................................... 9

Installation Procedure........................................ 10

Commissioning...................................................... 12

Operation............................................................... 13

Servicing & Maintenance....................................... 14

Spare Parts............................................................ 17

Troubleshooting..................................................... 20

Notes ..................................................................... 22

Limited Warranty and Remedy .............................. 24

Contents

Thermostatic Mixing Valves (LPM and BAR)

Model

320

Pressure Drop (BAR) Min.

Flow CV

0.3 0.7 1.0 1.4 1.7 2.1 2.4 2.8 3.1 3.4

LPM 30.3 41.6 49.2 56.8 64.4 71.9 75.7 83.3 87.1 90.8 3.8 3.4

Thermostatic

Model 320

Thermostatic Mixing Valve of “sealed for life” disposable

cartridge construction. Compact design with top and/or bottom

blended water outlet makes the Model 320 ideal for recessed

enclosure, plumbing chase and utility/mechanical room

installation.

Complete operating mechanism of valve is enclosed in a

durable polymer cartridge for ease of field maintenance.

Powerful internal mechanism and non metallic wetted parts

resist mineral deposition.

Capable of close temperature control at diverse flow rates

between 1 gpm (3.8 lpm) and 24 gpm (91 lpm). Able to blend

within 5°F (2°C) of either inlet supply due to “low seepage”

across internal proportioning mechanism.

Operational Specifications

• Dual thermostatic elements provide redundancy in the

event of individual thermostat failure

• Typical outlet temperature control +/-2°F

• Adjustable maximum temperature limit stop

• Adjustable single temperature lockout

• Thermal shutdown mode upon inlet supply failure

Technical Specifications

• 3/4” MNPT inlets and 3/4” MNPT outlet

• Chrome-plated brass/polymer construction

• Lead Free compliant

• Operating pressures

Maximum: 150 psi (10 bar)

Minimum: 10 psi (.7 bar)

• Integral inlet check valves and strainers

• ASSE 1017 and CSA B125 certified

• Shipping weight 10 lbs (4.5 kg)

Thermostatic Mixing Valves (GPM and PSI)

Model

320

Pressure Drop (PSI) Min.

Flow CV

5 10 15 20 25 30 35 40 45 50

GPM 8 11 13 15 17 19 20 22 23 24 1.0 3.4

Designs, materials, weights and performance ratings are

approximate and subject to change without notice. Visit

armstronginternational.com for up-to-date information.

Armstrong Hot Water Group, 221 Armstrong Blvd., Three Rivers, MI 49093 – USA

Phone: 269-279-3602, Fax: 269-279-3130

Water Temperature Control - Groups of Fixtures

4.61

(117.0)

7.29

(185.2)

1.04

(49.3)

5.38

(136.6)

HOT

INLET

COLD

INLET

MIXED

OUTLET

Thermostatic Mixing Valves (GPM and PSI)

Model

320D

Pressure Drop (PSI) Min.

Flow CV

5 10 15 20 25 30 35 40 45 50

GPM 8 11 13 15 17 19 20 22 23 24 1.0 3.4

Designs, materials, weights and performance ratings are

approximate and subject to change without notice. Visit

armstronginternational.com for up-to-date information.

Armstrong Hot Water Group, 221 Armstrong Blvd., Three Rivers, MI 49093 – USA

Phone: 269-279-3602, Fax: 269-279-3130

Thermostatic

Model 320D

A derivative of the standard Model 320 Thermostatic Mixing

Valve for institutional group fixture control. Compact design with

top and/or bottom blended water outlet makes Model 320 ideal

for recessed enclosure, plumbing chase and utility/mechanical

room installation.

Factory supplied pre-plumbed and pressure-tested Model

320D is supplied as standard with inlet check valves, strainers,

unions, isolations valves and outlet thermometer and stop

valve*.

*Model 320D is supplied with top outlet and can be site

reconfigured for bottom outlet applications.

Operational Specifications

• Dual thermostatic elements provide redundancy in the

event of individual thermostat failure.

• Typical outlet temperature control +/-2°F

• Adjustable maximum temperature limit stop

• Adjustable single temperature lockout

• Thermal shutdown mode upon inlet supply failure

Technical Specifications

• 3/4” NPT inlets and 3/4” NPT outlet

• Chrome plated brass/polymer construction with self finish

brass and bronze lead free components

• Lead Free compliant

• Operating pressures

Maximum: 150 psi (10 bar)

Minimum: 10 psi (.7 bar)

• Inlet check valves, strainers, unions and isolation valves

• Fitted with outlet thermometer and isolation valve

• ASSE 1017 and CSA B125 certified

• Shipping weight 18 lbs (8.1 kg)

For a submittal drawing, refer to D61051.

Water Temperature Control - Groups of Fixtures

Thermostatic Mixing Valves (LPM and BAR)

Model

320D

Pressure Drop (BAR) Min.

Flow CV

0.3 0.7 1.0 1.4 1.7 2.1 2.4 2.8 3.1 3.4

LPM 30.3 41.6 49.2 56.8 64.4 71.9 75.7 83.3 87.1 90.8 3.8 3.4

7.6

(194)

3.8

(97)

TYP

12.2

(311)

7.8

(198)

TYP

Specications

*Model 320 can accept temporary excursions above 185°F (85°C) and maintain control without sustaining

internal damage. (ASSE 1017 certification requires exposure to 200°F (93°C) for a period of 30 minutes).

Prolonged operation of the Mixing Valve at such elevated temperatures is not recommended.

** Normal operating conditions are considered as a differential of approximately 122°F (50°C) between

the hot and cold inlet temperatures, and with differentials of 59°F (15°C) - 95°C (35°C) between the

blend setting and either supply. 59°F (15°C) is the optimum published minimum differential required to

achieve full thermal performance.

General Advisory

This Model 320 Valve has been supplied for this application based upon information provided to Armstrong at the

time the order was placed.

This Model 320 Valve is configured for use in a “dead-leg” piping configuration.

This Model 320 Valve has not been congured for use in a central pumped re-circulation system.

This Model 320 Valve is not designed to deliver tepid water to emergency fixtures.

For further information, please call our technical department 1-269-279-3602 between 08:00 a.m. to

05:00 p.m. EST.

Operating Specications

Maximum Hot Water Supply Temperature185° 185°F (70°C)*

Minimum Cold Water Supply Temperature33° 33°F (1°C) - 77°F (25°C)

Optimum Minimum Inlet to Outlet Temperature Differential 59°F (15°C)**

Optimum Thermostatic Control Range 86°F (30°C) - 122°F (50°C)

Flow Rate at 45 psi 23 gpm (87 lpm)

Minimum Flow Rate 1 gpm (3.8 lpm)

Maximum Inlet Supply Pressure 150 psi (10 bar)

Minimum Inlet Supply Pressure 10 psi (0.7 bar)

Safety

Applicable codes must be followed and supersede any other instructions.

Generally applicable codes in the US include:

• IPC (International Plumbing Code)

Read this manual

Improper installation or operation may cause a ood resulting in property

damage, personal injury, or death. Armstrong strongly recommends that

a qualied installer be used.

Service must be performed by a qualied person.

Improper installation, start-up, operation, maintenance, or service may

void the warranty.

Hot water or metal may cause scald burns. Skin exposure to 140°F water

or metal for only ve seconds may cause a second degree burn.

Icon Legend

If instructions are not followed:

- injury or death and property damage are imminent

- injury or death and property damage are possible

- potential property damage, expensive repairs, and/or voiding

the warranty may result

The function of a Thermostatic Mixing Valve is to deliver water consistently at a pre-designated temperature.

Model 320 Thermostatic Mixing Valves are precision engineered to give continued superior and safe

performance provided:

1. They are installed, commissioned, operated and maintained in accordance with the recommendations

provided and accepted plumbing practices.

2. Periodic attention is given, as necessary, to maintain the product, the accessory fittings and the plumbing

system in good functional order.

In keeping with every other mechanical product, Model Mixing Valves should not be considered as

functionally infallible and, as such will never totally replace the vigilance and attention of facility nursing/

bathing or other institutional supervisory or industrial safety staff.

Provided that they are installed, commissioned, operated and maintained, the risk of product failure and

its associated consequences, if not eliminated, are reduced to the minimum achievable.

Pack Contents

X 1 

X 3 

X 1 

Schematic Piping

Hot Water Supply

Water Heater

Model 320

Mixed Flow

Cold Water Supply

System Layout

Thermometer

Sink

Shower

Check Valve

Isolation Valve

Stop Valve

Flow Direction

Pipeline

Installation

General

Installation must be carried out in accordance with these instructions, and must be conducted by designated,

qualied and competent personnel.

The installation must comply with all relevant local and state water plumbing codes.

All plumbing components are to be supplied by the installer. Failure to include these components will compromise

the product, system performance and will void the warranty.

Notes:

1. Model 320 is supplied fully performance and pressure tested.

2. Suitable connections for ease of maintenance should be used on the inlet and outlet ports. (Isolation valves

and unions.)

3. The hot and cold water inlet supply pressures must be nominally equal.

4. The inlet supply pipework must be thoroughly ushed before tting the Model 320 valve.

5. The Model 320 can be installed in both rising supplies and falling supplies.

Installation Requirements

The use of supply strainers will reduce debris entering the Model 320. The recommended gauge for such

strainers is 35 mesh (mesh aperture dimension = 0.5mm).

Inlet pressure tappings which allow measurement of the inlet pressures to the Model 320 under operating

conditions are particularly recommended for in-service testing.

Pipework must be rigidly supported to avoid any strain on the connections.

Inlet and outlet threaded joint connections should be made with PTFE thread sealing tape or liquid sealant.

Do not use oil-based, non-setting joint compounds.

Run water for 1 minute from both hot and cold supplies to eliminate pipe debris. It is essential that supply

pipes are thoroughly ushed through before connection to the Model 320.

Tools Required

Driling Drill Bit Screw Driver Pencil Adjustable Allen Keys Safety

Machine size 6 mm Plus & Minus Spanner 3mm & 2.5mm Glasses

Ø 6 mm

a. Unscrew the set screw.

b. Remove the Backplate.

a. Use the Backplate to mark the four mounting holes at

the desired height.

b. Drill the holes (6 mm) and t the wall anchors. Screw

the Backplate to the wall.

Caution! Avoid area where underground wirings

or pipelines pass through.

a. Mount the Valve assembly on the Backplate xed on

the wall. Make sure the Valve assembly locks in the

groove.

b. Tighten the set screw.

a. Important! Prior to assembly of the hot and cold

adapters, look inside each one and ensure that there

is a strainer and a white plastic checkvalve. The

adapter with nothing inside is for the outlet.

Thread the coupling nuts onto the Valve assembly

then tighten using an adjustable spanner.

Caution! Use a soft cloth to protect the plating

from damage while tightening the spanner.

Step 1

Step 3

Step 2

Step 4

2.5 mm

6.0 mm

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Unidad de control de Armstrong

Armstrong

Armstrong FTV Manual de usuario

Armstrong

Armstrong The Brain DRV25 Manual de usuario

Armstrong

Armstrong GP-2000 Manual de usuario

Armstrong

Armstrong Emech F3 Manual de instrucciones

Armstrong

Armstrong GD-10 Manual de usuario

Armstrong

Armstrong Steamix VE-M Manual de instrucciones

Armstrong

Armstrong BRAIN DMC80 Manual de usuario

Armstrong

Armstrong TVS 6000UD Manual de usuario

Armstrong

Armstrong 1-AV Manual de usuario

Armstrong

Armstrong OB 2000PT Manual

Armstrong

Armstrong A Series Manual de usuario

Armstrong

Armstrong The Brain DRV80R Manual de usuario

Armstrong

Armstrong 32-LD Manual de usuario

Armstrong

Armstrong GD-30 Manual de usuario

Armstrong

Armstrong GP-2000 Manual de usuario

Armstrong

Armstrong OB-2000PT Integral Manual de usuario

Armstrong

Armstrong Emech F5 Manual de instrucciones

Armstrong

Armstrong DRV40 Manual de usuario

Armstrong

Armstrong TVS 4000F Manual de usuario

Armstrong

Armstrong Emech F2 Manual de instrucciones

Armstrong

Armstrong CD72SR Manual de usuario

Armstrong

Armstrong Rada 320 Manual de instrucciones

Armstrong

Armstrong TVS-800 Series Manual de usuario

Armstrong

Armstrong GD-30 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario