Argox AS-8000 Series Manual de usuario

NOTICE:

This equipment has been tested and complied with

the limits for a Class a digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to

provide a reasonable protection against harmful

interface when the equipment is operated under a

commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the

instruction manual, may cause harmful interface to

radio communications. Operation of this equipment in

a residential area is likely to cause harmful interface in

which case the user will be required to correct the

interface at his own expenses.

Note: All brands and trademarks shall belong to their

respective owner.

Note: Specification is subject to changes without

notice.

This device complies with Part 15 of the FCC Rules.

Operation shall be subject to the following two

conditions:

(1) This device may not cause harmful interface, and

(2) This device must accept any interface received,

including interface that may cause undesirable

operation.

Using the ArgoxScan 8000

The ArgoxScan can automatically scan barcode at a distance.

Simply aim and pull the trigger. Code scanning is performed

along the center of the light bar emitted from the reading

window. This bar must cover the entire code.

Successful scanning shall be obtained by tilting the scanner

with respect to the barcode to avoid direct reflections that

impair the reading performance.

Recommended Steps

When the required settings have been configured, all settings

are stored in non- volatile memory of scanner after reading

EXIT Label. Recommended steps are as follows.

1) Host interface will be automatically detected. User does

not need to set host interface for the scanner.

2) Set interface to optimize protocol of scanner with your

host in interface section.

3) Set system control of scanner, such as specific

adjustments double confirm, power saving, indicator

and scanning mode which you prefer usage in system

control section.

4) Set code options of scanner for your usage in code

option section. You must make sure to enable the

symbology first, then Min./Max. code length, code ID

checksum and truncate digits are also converted.

5) Set string format of the scanner, such as preamble,

postamble Prefix, suffix, code ID and code name

transmission for your application in string format

section.

Note: If still not work properly. Please contact your dealer for

further information.

CONTENTS

Chapter 1 Introduction

Introduction…………………………..………………. 1

Default Setting ………………………………………. 2

ArgoxScan 8000 specification …………………….. 3

Programming the ArgoxScan 8000 Series Scanner 6

Chapter 2 Parameter Setting

Interface……………………………………………….… 8

Interface Selection ………………………………….. 8

Keyboard wedge ……………………………………. 9

RS-232 …………………………………………….…. 14

Pin Assignments ……………………………………. 17

System Control………………………………………. 18

Indication……………………………………………. 18

Transmission……………………..………………… 20

Scan…………………………………………………. 24

String Setting……………………………………….. 28

Code Option…………………………………….……… 31

UPCA ……………………………………..…………. 31

UPCE ………………………………………………… 34

EAN-13 ………………………………………………. 38

EAN-8 ………………………………………………… 42

Code 39 ……………………………………………… 46

Interleaved 2 of 5 …………………………………… 50

Industrial 2 of 5 ……………………………………… 52

Matrix 2 of 5 Eur …………………………………… 54

Codabar ……………………………………………… 56

Code-128 …………………………………………… 59

Code-93 ……………………………………………… 63

Code-11 ………………………………………….…… 66

MSI/Plessey …………………………………………. 68

UK/Plessey ………………………………………….. 70

Telepen ………………………………………………. 72

Standard 2 of 5 ……………………………………… 74

RSS-14 ………………………………………………. 76

RSS-Limited…………………………………..…… 78

RSS-Expanded…………………………………..….. 80

China Post …………………………………………… 82

Italian pharmacode ………………………………… 84

Appendix………………………………………………… 86

Test Chart ……………………………………………. 86

ASCII Code Table …………………………………… 89

Parameter setting List ………………………………. 90

Introduction

Installation- Keyboard Wedge

1) First of all, you must switch off power for the

terminal/computer.

2) Disconnect the keyboard cable from the back of the

terminal/computer and connect to the interface cable of

the scanner.

3) Connect the interface cable of the scanner to the

terminal/computer.

4) Turn the terminal/computer power on.

RS-232

1) Disconnect power to the terminal/computer.

2) Connect the external power supply (DC adapter) to the

interface cable of the scanner.

3) Plug the serial connector into the serial port on the back

of your computer/terminal. Tighten the two screws to

secure the connector to the port.

4) Plug the power pack into power source.

5) Once the scanner has been fully connected, turn the

terminal/computer power back on.

USB (Simulate with keyboard wedge)

1) Connect the USB cable between to the

terminal/computer.

2) Windows will automatically detect the USB device.

Note: If any of the above operation is incorrect, turn off the

power immediately and checking any improper

connections. Go through all above steps again.

Default setting

For each barcode shown as below:

Code Type Read

Enable

Checksum

erification

Enable

Checksum

Transmission

Enable

Code

UPC-A V V VA

UPC-E V V VE

EAN-13 V V VF

EAN-8 V V VFF

Code-39 V ＊

Interleaved

2 of 5 V I

Industrial

2 of 5 - - I

Matrix 2 of 5 B

Codabar %

Code-128 V V #

Code-93 V two digits &

Code-11 VOne digit O

MSI/Plessey V @

UK/Plessey V @

Telepen S

Standard 2 of 5 I

RSS-14 - - R4

RSS-Limited - - RL

RSS-Expanded - - RX

China Post - - t

Italian

Pharmacode. - - p

AS-8000 Specification

Weight 90 g (cable not included)

Cable – K/B wedge Straight 2.0 m

ArgoScan 8000 series

Specification Model AS-8000 series

Operational

Light Source 660 nm Visible Red LED

Optical System 2048 pixel CCD

(Charge-coupled device)

Depth of Scan Field 0-180 mm

(CODE 39, 500Lux, PCS=90%, 20mils)

Scanning Width 50 mm wide @ 10mm

Scan Speed 100 scans/sec

Resolution 0.1mm (4mils) Code39,PCS=90%

Print Contrast 45% or more

Scanning Angle Pitch: 60° Yaw: 70°

Decode Capability Auto-discriminates all standard one

dimension barcodes

Beeper Operation 7 tones or no beep

Indicator Green led and beep sound

Mechanical

Length 176 mm

Width-handle 40 mm

Width-head 67 mm

Depth-handle 30 mm

Depth-head 40 mm

Connector type Crimp type female connector

Case material ABS plastic

Cushion material TPR

Electrical

Input Voltage 5 VDC ± 0.25V

Power - Operating Max. 750 mW

Power - Standby 150 mW

Current - Operating Max. 150 mA @ 5 VDC

Current - Standby 30 mA @ 5 VDC

DC Transformers Class 2; 5VDC @ 450 mA

Agency listing FCC Class A, CE

Environmental

Operating

Temperature 0℃to 45℃(32℉to 113℉)

Storage -20℃to 60℃

(-4℉to 140℉)

Humidity 10% to 90% relative humidity,

non-condensing

Light Level Up to 20000 Lux

Shock 1.5m drop onto concrete

Contaminants Seals to resist airborne particulate

contaminants

Ventilation None required

Programming

method

Manual (Reading special barcode),

DOS command through RS-232

(RS-232 model)

Programmable

characteristics

Code type selection, check digit

selection, Decoding option

Transmitted character delay, Header

selection, trailer selection, message

suffix, good read beep tone and

volume, scanner trigger selection

Keyboard emulation type

(intermessage delay, keyboard type

and keyboard language)

Serial interface type (ACK/NAK,

Xon/Xoff, RTS/CTS, good read LED

control, start/stop bits)

Otros manuales para AS-8000 Series

Tabla de contenidos

Otros manuales de Lector de código de barras de Argox

Argox

Argox Xellent X-3200ZE Manual de usuario

Argox

Argox D2 Series Manual de usuario

Argox

Argox D2 Series Manual de usuario

Argox

Argox G6000 Manual de usuario

Argox

Argox P4 Series Manual de usuario

Argox

Argox AS-9500 Manual de usuario

Argox

Argox AS-8060 Manual de usuario

Argox

Argox OS-214 plus Manual de usuario

Argox

Argox AS-8520 Manual de usuario

Argox

Argox AS-8000 Series Manual de usuario

Argox

Argox AR-3201 Manual de usuario

Argox

Argox PT Manual de usuario

Argox

Argox AS-8120 Manual de usuario

Argox

Argox AS-8020 Manual de usuario

Argox

Argox AI-6800 Manual de usuario

Argox

Argox OS Series Manual de usuario

Argox

Argox D2 Series Manual de usuario

Argox

Argox A-2240 Manual de usuario

Argox

Argox OS Series Manual de usuario

Argox

Argox Xellent X-1000VL Manual de usuario

Argox

Argox AS-8312 Manual de usuario

Argox

Argox AS-8510 Manual de usuario

Argox

Argox D2 Series Manual de usuario

Argox

Argox AI-6821 Manual de usuario

Manuales populares de Lector de código de barras de otras marcas

POSMicro

POSMicro Datalogic PowerScan D7100 Manual de usuario

Marson

Marson MT780 Guía de configuración rápida

NCR

NCR RealPOS Manual de usuario

Motorola

Motorola SE3300 Guía de configuración rápida

Element

Element P130BT Manual de usuario

Motorola

Motorola Symbol LS3008 Manual de instalación y operación

Meec tools

Meec tools OBD-II / VAG Manual de usuario

SICK

SICK CLP 100 Manual de usuario

Royal Tag SA

Royal Tag SA I-Read Manual de usuario

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manual de usuario

Meteor

Meteor 8310 Manual de usuario

Denso

Denso BHT-500B Manual de usuario

Datalogic

Datalogic Heron HD3130 Manual de usuario

Motorola

Motorola MP6000 Instrucciones de montaje

Newland

Newland NLS-HR15-BT Manual de usuario

ARTDEV

ARTDEV AS-1310 Manual de usuario

Aopos

Aopos AS290 Manual de usuario

ENS

ENS 367-5455 Manual de usuario