Argox AS-8000 Series Manual de usuario

AS-8000 SERIES

MANUAL

ARGOX

NOTICE:

This equipment has been tested and complied with

the limits for a Class a digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to

provide a reasonable protection against harmful

interface when the equipment is operated under a

commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the

instruction manual, may cause harmful interface to

radio communications. Operation of this equipment in

a residential area is likely to cause harmful interface in

which case the user will be required to correct the

interface at his own expenses.

Note: All brands and trademarks shall belong to their

respective owner.

Note: Specification is subject to changes without

notice.

This device complies with Part 15 of the FCC Rules.

Operation shall be subject to the following two

conditions:

(1) This device may not cause harmful interface, and

(2) This device must accept any interface received,

including interface that may cause undesirable

operation.

iii

Using the ArgoxScan

8000/8110/8120/8150/8250/8310/8312

The ArgoxScan can automatically scan barcode at a distance.

Simply aim and pull the trigger. Code scanning is performed

along the center of the light bar emitted from the reading

window. This bar must cover the entire code.

Successful scanning shall be obtained by tilting the scanner

with respect to the barcode to avoid direct reflections that

impair the reading performance, especially for 2D barcode.

Recommended Steps

When the required settings have been configured, all settings

are stored in non- volatile memory of scanner after reading

EXIT Label. Recommended steps are as follows.

1) Set right host interface for your scanner.

(The scanner is in factory default shown as bold label)

2) Set interface to optimize protocol of scanner with your

host in interface section.

3) Set system control of scanner, such as specific

adjustments double confirm, power saving, indicator

and scanning mode which you prefer usage in system

control section.

4) Set code options of scanner for your usage in code

option section. You must make sure to enable the

symbology first, then Min./Max. code length, code ID

checksum and truncate digits are also converted.

5) Set string format of the scanner, such as preamble,

postamble Prefix, suffix, code ID and code name

transmission for your application in string format

section.

Note: If still not work properly. Please contact your dealer for

further information.

Table of Contents

Introduction ................................................ 1

Default setting......................................... 2

ArgoScan 8000 / 8120 ............................ 4

ArgoScan 8150 / 8250 / 8310 / 8312 ...... 7

Programming the ArgoScan.................. 10

Parameter Setting...................................... 12

Interface Selection ................................ 12

Keyboard wedge ................................... 13

RS-232 .................................................. 18

Wand Emulation ................................... 21

Pin Assignments ................................... 24

System Control ......................................... 27

Scan ...................................................... 27

Indication .............................................. 33

Code Option.............................................. 35

UPCA.................................................... 35

UPCE .................................................... 41

EAN-13................................................. 44

EAN-8................................................... 49

Code 39................................................. 53

Interleaved 2 of 5 .................................. 57

Matrix 2 of 5 Eur .................................. 61

Codabar................................................. 63

Code-128/GS1-128............................... 66

Code-93 ................................................ 70

Code-11................................................. 73

MSI/plessey .......................................... 75

UK/plessey............................................ 77

Telepen.................................................. 78

Standard 2 of 5...................................... 81

China Post............................................. 83

Italian Pharmacode (Code 32) .............. 85

Code-16K (for 8250/8312) ................... 87

PDF-417 (for 8250/8312) ..................... 89

EAN UCC Composite (for 8312) ......... 91

RSS-14.................................................. 93

RSS-Limited ......................................... 95

RSS-Expanded...................................... 97

Micro-PDF (for 8312) .......................... 99

String Format ...................................... 100

String setting / Transmission (Prefix /

Suffix) ................................................. 101

String setting/Transmission

(Preamble/Postamble)......................... 103

String setting / Transmission (Insert

Group Characters)............................... 105

String setting / Transmission (Insert

Group Characters)............................... 106

String setting / Transmission (Others) 109

Appendix .................................................111

Test Chart.............................................111

ASCII Code Table................................115

Parameter Setting List .........................117

Introduction

Installation- Keyboard Wedge

1) First of all, you must switch off power for the

terminal/computer.

2) Disconnect the keyboard cable from the back of the

terminal/computer.

3) Connect the appropriate interface cable to the scanner

and to the terminal/computer.

4) Turn the terminal/computer power on.

RS-232

1) Disconnect power to the terminal/computer.

2) Connect the appropriate interface cable and external

power supply (DC adapter) to the scanner.

3) Plug the serial connector into the serial port on the back

of your computer/terminal. Tighten the two screws to

secure the connector to the port.

4) Plug the power pack into power source.

5) Once the scanner has been fully connected, turn the

terminal/computer power back on.

USB (Simulate with keyboard wedge)

1) Connect the USB cable between scanner and PC.

2) Windows will automatically detect the USB device.

Note: If any of the above operation is incorrect, turn off the

power immediately and check any improper

connections. Go through all above steps again.

Default setting

For each barcode shown as below:

Code Type

Read

Enable

Checksum

Verification

Enable

Checksum

Transmission

Enable

Code

8000 / 8120

UPC-A

UPC-E

EAN-13

EAN-8

Code-39

＊

Interleaved

2 of 5

Industrial

2 of 5

Matrix 2 of 5

Codabar

Code-128

Code-93

V two digits

Code-11

VOne digit

MSI/Plessey

UK/Plessey

Telepen

Standard 2 of 5

RSS-14

RSS-Limited

RSS-Expanded

China Post

Italian

Pharmacode.

Code Type

Read

Enable

Checksum

Verification

Enable

Checksum

Transmission

Enable

Code

8150

8250

8310

8312

UPC-A

UPC-E

EAN-13

EAN-8

Code-39

＊

Interleaved

2 of 5

Industrial

2 of 5

Matrix 2 of 5

Codabar

Code-128

Code-93

V two digits

Code-11

VOne digit

MSI/Plessey

UK/Plessey

Telepen

Standard 2 of 5

China Post

Italian

Pharmacode.

Code-16K

PDF417

EAN UCC

Composite

RSS-14

RSS-Limited

RSS-Expanded

Micro-PDF

8312

only

ArgoScan 8000 / 8120

Weight

90g

120 g

Specification

Model 8000

Model 8120

Operational

Light Source

660 nm Visible Red LED

Optical System

2048 pixel CCD

(Charge-coupled device)

Depth of Scan Field

0-150 mm

(CODE 39,

PCS=90%, 20mils)

0-150 mm

(code 39,

PCS=90%, 20mils)

Scanning Width

75mm at contact

Scan Speed

100 scans/sec

Resolution

4mils, Code39, PCS=90%, on contact

Print Contrast

45% or more

Scanning Angle

Pitch: 60° Skew: 75°

Decode Capability

Auto-discriminates all standard

barcodes; Other symbologies can be

ordered optionally

Beeper Operation

7 tones or no beep

Indicator

Green led

Blue led

Mechanical

Length

176 mm

182mm

Width-handle

26mm

Width-head

90mm

Depth-handle

30 mm

49mm

Depth-head

40 mm

35mm

Otros manuales para AS-8000 Series

Tabla de contenidos

Otros manuales de Lector de código de barras de Argox

Argox

Argox AP-9800 Manual de usuario

Argox

Argox AS-8000 Series Manual de usuario

Argox

Argox AI-6821 Manual de usuario

Argox

Argox ArgoxScan 9500 Manual de usuario

Argox

Argox OS-214 plus Manual de usuario

Argox

Argox P4 Series Manual de usuario

Argox

Argox Smart CP-2140 Manual de usuario

Argox

Argox P4 Series Manual de usuario

Argox

Argox D2 Series Manual de usuario

Argox

Argox OS-214 plus Manual de usuario

Argox

Argox AS-8020 Manual de usuario

Argox

Argox OS-214 plus Manual de usuario

Argox

Argox P4 Series Manual de usuario

Argox

Argox Xellent X-3200ZE Manual de usuario

Argox

Argox AS-8060 Manual de usuario

Argox

Argox AS-9300 Manual de usuario

Argox

Argox AS-8000 Series Manual de usuario

Argox

Argox AS-9500 Manual de usuario

Argox

Argox Smart CP-2140 Manual de usuario

Argox

Argox AS-8520 Manual de usuario

Argox

Argox AS-8312 Manual de usuario

Argox

Argox G Series Manual de usuario

Argox

Argox Smart CP-2140 Manual de usuario

Argox

Argox AS-8520 Manual de usuario

Manuales populares de Lector de código de barras de otras marcas

POSMicro

POSMicro Datalogic PowerScan D7100 Manual de usuario

Marson

Marson MT780 Guía de configuración rápida

NCR

NCR RealPOS Manual de usuario

Motorola

Motorola SE3300 Guía de configuración rápida

Element

Element P130BT Manual de usuario

Motorola

Motorola Symbol LS3008 Manual de instalación y operación

Meec tools

Meec tools OBD-II / VAG Manual de usuario

SICK

SICK CLP 100 Manual de usuario

Royal Tag SA

Royal Tag SA I-Read Manual de usuario

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manual de usuario

Meteor

Meteor 8310 Manual de usuario

Denso

Denso BHT-500B Manual de usuario

Datalogic

Datalogic Heron HD3130 Manual de usuario

Motorola

Motorola MP6000 Instrucciones de montaje

Newland

Newland NLS-HR15-BT Manual de usuario

ARTDEV

ARTDEV AS-1310 Manual de usuario

Aopos

Aopos AS290 Manual de usuario

ENS

ENS 367-5455 Manual de usuario