Arecont Vision AV818X Manual de usuario

AV818X/AV836X Installation Manual

1. Prepare mounting area as shown on Pic. 1.

Note, you need either #10-32 threaded inserts or you can use thru holes in desired surface

and #10 washers and #10-32 nuts (not included)

2. Remove two #4-40 screws on the top of the camera.

3. Remove retaining ring and plastic dome. There are four #10 countersunk holes in front camera

base.

4. Using enclosed four #10-32 FH Phillips screws attach camera to the desired surface.

5. Place plastic dome into retaining ring so the flange of the dome rests inside of retaining ring.

6. Carefully rotate dome inside of the ring until holes in ring and dome will match

7. Place retaining ring and dome onto front camera base, matching holes in ring and dome with

two #4 threaded holes in base.

8. Secure retaining ring and dome to front camera base, using screws from step 2,

PIC.1

BACK COVER WITH MOUNTING DIMENSIONS

www.arecontvision.com avsales@arecontvision.com 818.937.0700 877.CAMERA.8

AV818X/AV836X Tilt Adjustment Instruction A

AV8180 is supplied with 3 shaft holders stocked up on each side (further referred to as

“floors”) Camera is installed on the 2nd floor as a default.

If you use camera in installation such way so the center plane of the Main Bracket with 4

lenses is perpendicular to the mounting surface, you need to move camera to the 1st floor

to fit camera in dome. (Instruction A)

If you use camera in installation such way so the center plane of the Main Bracket with 4

lenses is parallel to the mounting surface you need to move camera to the 3rd floor.

(Instruction B)

PIC. 2

INSTRUCTION A:

1. Use enclosed 1/16” hex L-key to undo set screws on the top of the “second

floor” shaft holders, while holding the bracket. Don’t completely remove set

screws from holders. Carefully place bracket on its side.

2. Using enclosed 5/64” hex L-key remove 4 screws from shaft holders.

3. Remove “1st floor” and “3rd floor” shaft holders from both sides. Place shaft

holders with set screws onto the main plate.

4. Using screws from step 2 attach both holders to main plate. (see Pic. 2 for

positioning)

5. Secure bracket axis with set screws, using 1/16” hex L-key.

6. Cut the excess of fabric with the blade or scissors if necessary.

7. Do not discard holders as they may be used in future installation modifications.

www.arecontvision.com avsales@arecontvision.com 818.937.0700 877.CAMERA.8

AV818X/AV836X Tilt Adjustment Instruction B

INSTRUCTION B:

1. Make sure that bracket lies on the same side as an open threaded hole next to

shaft holders. This is your “standard” installed position (see Pic. 3, holes

circled)

2. Remove top fabric sheet.

A. Using 1/16” hex L-key undo 5 screws on the top of the bracket to release

upper end of the fabric. Set small bracket aside

B. Remove 2 screws to release middle section of the fabric.

C. Remove 5 screws from the bottom arc, set arc aside and remove fabric sheet.

3. Note the position of shaft holders on the main plate in relationship to open

threaded hole next to shaft holders.

4. Using enclosed 1/16” hex L-key undo set screws on the top of the “second

floor” shaft holders, but don’t completely remove set screws from holders.

5. Using enclosed 5/64” hex L-key remove 4 screws from shaft holders.

6. Switch shaft holders so the ones with set screws will be on the top (3rd floor)

Make sure that:

A. Shaft holders are on the same positions as they were before modification

(see Pic. 2)

B. Shaft holders with set screws are the “top floor”

7. Install Bracket on the “3rd floor”.

8. Using 4 #6-32 1.5”LG. screws from step 5 attach both structures to main

plate.

9. Secure bracket axis with set screws, using 1/16” hex L-key.

10. Install enclosed fabric sheet. Note that fabric sheet is smooth on one side and

rough on another. Rough side is conductive and should face out. Smooth

(isolated) side is facing PCBs. If you have any doubts, use conventional tester:

rough surface shows no electrical resistance.

A. Line up upper edge of the fabric with upper edge of the bracket. Place small

bracket from 2A on the top of the fabric. Using 1/16” hex L-key install 5

screws from step 2A.

B. Line up bottom edge of the fabric with outer edge of the bottom arc from

step 2C and using 1/16” hex L-key install 5 screws from step 2C.

C. Install 2 screws from step 2B

11. Cut the excess of fabric with the blade or scissors.

12.

www.arecontvision.com avsales@arecontvision.com 818.937.0700 877.CAMERA.8

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cámara IP de Arecont Vision

Arecont Vision

Arecont Vision MegaDome AV3155 Manual de usuario

Arecont Vision

Arecont Vision Surround Video AV8180 Manual de usuario

Arecont Vision

Arecont Vision MegaVideo AV1305 Manual de usuario

Arecont Vision

Arecont Vision AV10005DN Manual de usuario

Arecont Vision

Arecont Vision AV3110 Manual de usuario

Arecont Vision

Arecont Vision MegaDome 2 AV1255AM Manual de usuario

Arecont Vision

Arecont Vision MegaDome AV5155 Manual de usuario

Arecont Vision

Arecont Vision MegaVideo AV3130 Manual de usuario

Arecont Vision

Arecont Vision MegaVideo AV2100-AI Manual de usuario

Arecont Vision

Arecont Vision AV12186DN SurroundVideo Manual de usuario

Arecont Vision

Arecont Vision Surround Video AV8185 Manual de usuario

Arecont Vision

Arecont Vision MicroDome AV1455DN-S Manual de usuario

Arecont Vision

Arecont Vision MegaVideo AV5110 Manual de usuario

Arecont Vision

Arecont Vision AV3236DN Manual de usuario

Arecont Vision

Arecont Vision AV3125IRv1 Manual de usuario

Arecont Vision

Arecont Vision MegaVideo AV5100-AI Manual de usuario

Arecont Vision

Arecont Vision MegaBall AV3146DN-3310-D-LG Manual de usuario

Arecont Vision

Arecont Vision AV10005 Manual de usuario

Arecont Vision

Arecont Vision MegaDome AV1355 Manual de usuario

Arecont Vision

Arecont Vision MegaVideo AV3100-AI Manual de usuario

Arecont Vision

Arecont Vision MegaDome AV2155 Manual de usuario

Arecont Vision

Arecont Vision MegaVideo AV5105 Manual de usuario

Arecont Vision

Arecont Vision AV12186DN SurroundVideo Manual de usuario

Arecont Vision

Arecont Vision MegaVideo AV2105 Manual de usuario

Manuales populares de Cámara IP de otras marcas

FLIR

FLIR Exx series Manual de usuario

Avigilon

Avigilon H4A-BO1-IR Manual de usuario

Digital Watchdog

Digital Watchdog DWCA-C128-64 Manual de usuario

ShareTech

ShareTech AV1 Manual de usuario

Ezviz

Ezviz C6C Manual de usuario

Melchioni

Melchioni UCAM 2015 Manual de usuario

Geutebruck

Geutebruck G-Cam/ESD-4630 Manual de usuario

Mitel

Mitel 6800i Series Manual de servicio

Vitek

Vitek VTC-IR403-212NP Manual de usuario

THOMSON

THOMSON DSC - 323W Manual de usuario

AVer

AVer FB2027 Manual de usuario

ENFORCER

ENFORCER EV-T5105-N2SQ Manual de usuario

Wansview

Wansview NC543 Manual de usuario

Eneo

Eneo MCB-64A0003M0A Manual de usuario

deView electronics

deView electronics CBDNI36F Manual de usuario

Swann

Swann SwannEye Manual de usuario

LevelOne

LevelOne IP CamSecure Manual de usuario

Digitus

Digitus DN-16085-1 Manual de usuario