Arduino MLT-BT05 Guía de configuración
MLT-BT05 4.0 Bluetooth module
Supports micro-airsync commumication, iOS and Android app communication, mast-slave modes and IO control
AT
Instruction
set
V3.0
MLT-BT05 4.0 Bluetooth Serial Communication Module
AT Directive
Users can communicate with the module using TX, RX lines at various baud rates
Supported rates: 9600, 19200,38400,57600,115200. The default is 9600bps 。
Detailed instructions
MLT-BT05 4.0 B uetooth modu e Command set
（Note ： AT commands require carriage return and ine feed; AT commands must be
issued before connecting. Once connected module is in data transmission mode. ）
（AT commands ARE case sensitive; end ines with \r\n ）
1. set/query master/slave mode:
instruction response parameter
AT+ROLE<Param> +ROLE=<Param>
OK
Param ：（ 0-4 ）
0 slave mode?
1 master mode?
2 sensor mode
3 iBeacon mode
4 WeChat mode
default ： 0
AT+ROLE +ROLE=<Param>
2. get software version number:
instruction response parameter
AT+VERSION +VERSION=<Param> Param ：MLT-BT05-V2.1
3. get module Bluetooth address:
instruction response parameter
AT+LADDR +LADDR =<Param> Param:MAC address
4. set/query device name:
instruction response parameter
AT+NAME<Param> +NAME=<Param>
OK
Param ：module
Bluetooth name
Default: MLT-BT05
longest ：18 byte
AT+NAME +NAME=<Param>
5. set/query match code ：
instruction response parameter
AT+PIN<Param> +PIN=<Param>
OK
Param ：6 byte bit
pairing password
default “：123456”
AT+PIN +PIN=<Param>
6. set/query broadcast interval:
instruction response parameter
AT+ADVI<Param> +ADVI=<Param>
OK
Param ：（ 0-6 ）
0 100ms
1 500ms
2 7500ms
3 1000ms
4 2000ms
5 4000ms
6 8000ms
default ： 0
AT+ADVI +ADVI=<Param>
7. set/query module authentication job type:
instruction response parameter
AT+TYPE<Param> +TYPE=<Param>
OK
Param ：( 0-2 )
0no password
1password pairing
2 password pairing
and binding
default ：0
AT+TYPE +TYPE=<Param>
8. set/query- seria baud rate:
instruction response parameter
AT+BAUD<Param> +BAUD=<Param>
OK
Param ：( 0-4 )
Values (decimal):
0 115200
1 57600
2 38400
3 19200
4 9600
default ：0
AT+BAUD +BAUD=<Param>
9. set/query-Service UUID ：
instruction response parameter
AT+UUID<Param> +UUID=<Param>
OK
Param: 0x0001~0xFFFE
default ：0xFFE0
AT+UUID +UUID=<Param>
10. set/query-Characteristic ：
instruction response parameter
AT+CHAR<Param> +CHAR=<Param>
OK
Param:0x0001~0xFFFE
default ：0xFFE1
AT+CHAR +CHAR=<Param>
11. set/query-iBeacon UUID ：
instruction response parameter
AT+IBSUUID<Param> +IBSUUID=<Param>
OK
Param ：
FDA50693A4E24FB1AFCFC6EB07647825
AT+IBSUUID +IBSUUID=<Param>
12. set/query-iBeacon Major ：
instruction response parameter
AT+MAJOR<Param> +MAJOR=<Param>
OK
Param : 0x0001~0xFFFE
default ： 0x0007
AT+MAJOR +MAJOR=<Param>
13. set/query-iBeacon Minor ：
instruction response parameter
AT+MINOR<Param> +MINOR=<Param>
OK
Param: 0x0001~0xFFFE
default ： 0x000A
AT+MINOR +MINOR=<Param>
14. software restart (reboot after 500mS):
instruction response parameter
AT+RESET OK no
15. enter low power mode (can be searched after entering):
instruction response parameter
AT+SLEEP +SLEEP:OK no
16. search for Bluetooth devices (master mode instructions):
instruction response parameter
AT+INQ<Param> OK Param ： 1-0
1: start scanning
0: stop scanning
17. connect the remote device (master mode command):
instruction response parameter
AT+CONN<Param> connection information Param ：0-7
18. get host scan to slave MAC address (master mode command):
instruction response parameter
AT+RSLV< Param > +RSLV=MACaddress
OK
Param ：( 0-7 )
19. bind device (master mode instruction) ：
instruction response parameter
AT+BAND<Param> +BAND=<Param>
OK
Param ：MAC address
AT+BAND +BAND=<Param>
20. unbind (main mode instruction) ：
instruction response parameter
AT+CLRBAND OK no
21. get the number of slaves to be scanned (main mode command) ：
instruction response parameter
AT+GETDCN<Param> +GETDCN=<Param>
OK
Param ：（ 1-8 ）
22. disconnect (main mode command) ：
instruction response parameter
AT+DISC OK no
23. disconnet (master mode command) ：
instruction response parameter
AT+GETSTAT +GETSTAT=<Param> Param ：（ 0-1 ）
0not connected
1connected
24. set/query -micro letter H5 factory server communication:
instruction response parameter
AT+AT_WXSWH<Param> +MINOR=<Param>
OK
Param ：（ 0-1 ）
0：H5 communication
1：factory server
Default: 0
AT+MINOR +MINOR=<Param>
Tabla de contenidos
Otros manuales de Unidad de control de Arduino
Arduino
Arduino MKR1000 Manual de usuario
Arduino
Arduino HM-11 Manual de usuario
Arduino
Arduino Nano 33 BLE Sense Rev2 Manual de usuario
Arduino
Arduino Nano 33 BLE Rev2 Manual de usuario
Arduino
Arduino NRF24L01 Instrucciones de operación
Arduino
Arduino Nano 33 BLE Manual de usuario
Arduino
Arduino Ethernet Shield 2 Manual de usuario
Manuales populares de Unidad de control de otras marcas
Festo
Festo Compact Performance CP-FB6-E Manual de lista de piezas
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manual de usuario
JS Automation
JS Automation MPC3034A Manual de usuario
JAUDT
JAUDT SW GII 6406 Series Guía rápida
Spektrum
Spektrum Air Module System Manual de usuario
BOC Edwards
BOC Edwards Q Series Manual de usuario
