Aqara FP2 Manual de usuario
Presence Sensor FP2 User Manual
Please read this manual carefully and keep it in a safe place.
The Presence Sensor FP2 features zone positioning, multi-person detection, and fall detection.
Capable of detecting presence or absence, falls, entries, exits, approach, departure, and
illuminance, it supports real-time tracking of multiple targets and zone settings. The FP2's
powerful features can also be used within third-party automation systems: multiple sensors are
exposed to HomeKit (and Home Assistant), Alexa, Google Home and more without needing a hub.
1. The fall detection results are for reference only. The product cannot fully replace medical devices
and may not accurately recognize slow tumbles or gradual falls while leaning against a wall.
Additionally, rapidly falling or shaking objects could trigger false fall detection alerts.
2. Avoid placing this product near a heat source.
3. Refrain from attempting self-repairs. All repairs should be conducted by professionals.
*This device requires to be used with the Aqara Home app.
*If local automation is needed, this product should be used with a Hub with Wi-Fi Local Automation features.
Product Introduction
Warnings
Sensor
Indicator LED, Light Sensor
Reset Button
USB-C to USB-A Cable
Base
Metal Plate
Sticker
Notice
Use of the Works with Apple badge means that an accessory has been designed to work specifically
with the technology identified in the badge and has been certified by the developer to meet Apple
performance standards. Apple is not responsible for the operation of this device or its compliance
with safety and regulatory standards.
Device Discription
Actions Description LED indicator
Device
power-on
Press the Reset
button for more
than 10s
1. If the device had been connected to a
network previously, the LED indicator is
as shown on the right.
2. If the device is not connected to a
network, it enters the networking mode.
The yellow indicator flickers quickly: Enter
the networking mode.
The white indicator is normally on: Failure
to connect to the router/AIOT
The blue indicator flickers quickly: Connect
to the router
The blue indicator flickers slowly: Connect
to AIOT
No indicator is on: The device is connected
successfully, and can work normally.
Reset the device. Aer successful reset, the
device will be restarted automatically and
enter the networking mode.
The yellow indicator flickers quickly
Press the Reset
button for 10
times
successively
Restore factory settings and reset the device
to enter the networking mode. The yellow indicator flickers quickly
Device installation and power-on
Choose between wall-mounted or ceiling-mounted positions for the FP2 based on the detection
range. For heights under 2 meters, use metal plate and sticker; for heights over 2 meters, use
screws.
Connect the FP2 with the Type-C sensor power cord, then insert the sensor cord into the USB-A
port of an adapter, outlet or other power supplying device. Long press the reset button for 10
seconds to reset FP2. Click 10 times to restore the factory settings, which shall clear all settings
and network data.
2
Download the app
Download the Aqara Home app: Search for "Aqara Home" in the Apple App Store, Google Play,
Xiaomi GetApps, Huawei App Gallery, or scan the following QR code to download the Aqara Home
app.(QR Code)Device Binding & Initialization
* Due to upgrades and updates of the Aqara Home app, the actual operations may differ from the above description. Please
operate it according to the instructions of the Aqara Home app.
3
For fall detection, the ceiling-mounted method is advised:
at an installation height of 2.8 meters, it can cover a fall
detection area with a radius of 2 meters.
Select an installation method
Based on the actual application scenario, determine the appropriate
installation method and required detection range for the FP2.
For zone detection, the wall-mounted method is recommended: it
offers a horizontal detection angle of 120 degrees, with blind spots
appearing beyond 120 degrees; the radial detection distance is 8
meters and the detection width is 6 meters.
Device Binding & Initialization
1
1. If you use HomeKit to add the device, you can either scan the Apple setup code on the device as
prompted by the app or manually enter the PIN code.
2. If the binding fails, please confirm whether the following reasons exist:
• The device only supports the Wi-Fi network of 2.4GHz band.
• Unsupported special characters in the Wi-Fi name or password may cause connection failure.
• Change them to commonly-used characters before trying again.
• The device does not currently support WPA/WPA2 enterprise-class Wi-Fi networks.
• Check if the router has enabled Wi-Fi anti-squatting settings or AP isolation, as these could result in
connection or device search failures within the local area network.
• Bridge connection networks are not recommended.
3. Common HomeKit addition failures include:
• If it prompts "No accessories can be added," restart the iOS device (iPhone or iPad) and reset the
FP2 before trying again, as the error message might be cached in the iOS system due to repeated
adding failures.
• If it prompts "accessories have been added," restart the iOS device, reset the FP2, and manually
enter the HomeKit setting code to add the doorbell.
• If it prompts "no accessories are found," reset the FP2, wait for 3 minutes, and manually enter the
HomeKit setting code to add it again.
Device binding
Open the app, tap "+" in the upper right corner of the homepage to enter the page of "Add the
device". Choose "Presence Sensor FP2" and then install the device according to the instructions.
4
Indicator Description
LED status Device status & operation instructions
The yellow
indicator is
normally on
Aer the device is powered on, the yellow status indicator is normally on until the
system start-up of the device is finished.
The blue indicator
flickers quickly When the device is being connected to the router, the blue indicator flickers quickly.
The blue indicator
flickers slowly
Aer successfully connected to the router, the device is being connected to the AIOT
platform,
The blue indicator
flickers quickly The device is offline and is not connected to the router
The white indicator
is normally on. No password/failed to connect to the router/failed to connect to AIOT
The red indicator is
normally on
Device fault (overtemperature and excessive acceleration vibration can cause the
device to enter a state where the sensor cannot work normally)
The yellow
indicator flickers
slowly
The user can update the firmware through APP OTA. In the process of updating, the
status indicator of the device is set to yellow indicator flickering slowly
Blue indicator
flickers twice
quickly
Identify function. When searching for the device via APP, the blue indicator of the
device will react by flickering twice
The indicator is off
Aer successfully connected to the AIOT, the status light of the device is off (different
from that of the gateway, the device enters the working state aer connected to a
network); If the device cannot be connected to the AIOT aer successful networking
and can be connected to the router, the status indicator will be still off.
The yellow indicator
flickers quickly
Aer the system start-up or reset is completed, the device enters the AP or Bluetooth
network configuration mode and waits to receive the state information of WiFi. The
status indicator is set to yellow indicator flickering quickly before the networking
information received;
Device Card and Homepage
Once bounded, you can view the current status of the device on the FP2 device card, including
presence, absence, falling, and offline states. Illuminance is displayed through separate cards.
On the Presence Sensor FP2 device homepage, you can access the floorplan, coordinate
information, logs, zone management, and installation mode.
The floorplan is divided into 16x20=320 cells. Each cell represents a detection space of
0.5m x 0.5m = 0.25 square meters.
5
Installation Guidance
Aer bounded, you can follow the installation guide to configure important settings, including
modes, edges, and interference sources.
FP2 supports presence detection, zone dectection (Personnel positioning), falling detection.
Default mode is always on by default, regardless of selecting any two other modes.
6
Step 2: Edge Setting
The edge setting is primarily used to reduce false targets caused by signal reflections from walls or
other objects. It is recommended to set the area beyond the wall as the edge.
Step 3: Interference Source Configuring
Living and office spaces oen have moving targets such as curtains, fans, green plants moved by
wind, and clothes hanging. If the sensor faces these objects, a false alarm may easily occur, so it
needs to be marked as an interference source.
Note: Make sure to configure the interference source only aer ensuring that humans and pets have
le the area.
Otros manuales para FP2
1
Tabla de contenidos
Otros manuales de Accesorios de Aqara
Aqara
Aqara Door and Window Sensor Manual de usuario
Aqara
Aqara Water Leak Sensor Manual de usuario
Aqara
Aqara G4 Manual de usuario
Aqara
Aqara Motion Sensor Manual de usuario
Aqara
Aqara Water Leak Sensor Manual de usuario
Aqara
Aqara RTCGQ11LM Manual de usuario
Aqara
Aqara MCCGQ11LM Manual de usuario
Aqara
Aqara SJCGQ11LM Manual de usuario
Aqara
Aqara T1 Manual de usuario
Aqara
Aqara Temperature and Humidity Sensor Manual de usuario
