APS iBoard IB-R009 Manual de usuario
Customer Support: info@iboardauto.com
Rev. 20220401
1
iBoard
®
iBoard® by APS PART#: IB-R009
READ INSTRUCTIONS CAREFULLY BEFORE START ING
INSTALLATION. REMOVE CONTENTS FROM BOX AND
VERIFY ALL PARTS ARE PRESENT. ASSISTANCE IS
RECOMMENDED.
*ROCKER PANEL MOUNT
*NO DRILLING REQUIRED
Fastener Size Tightening Torque (ft-lbs) Required
6mm 6-7 √
8mm 16-18 √
10mm 31-32 X
12mm 56-58 X
14mm 92-94 X
Front
1# 1#
2#
2#
Customer Support: info@iboardauto.com
Rev. 20220401
2
iBoard
®
Hardware Package A (For Bracket Installation)
Item QTY Description Item QTY Description
1# 2Driver / Passenger Front Mounting Brackets 5# 8M8 Lock Washers
2# 2Driver / Passenger Rear Mounting Brackets 6# 4M8X1.25 Hex Nuts
3# 8M8X1.25-30 Hex Bolts 7# 4M8 Clip Nuts
4# 12 M8 Large Flat Washers
2#
1# 3#
Hardware Package B (For Step Bar Installation)
Item QTY Description Item QTY Description
1# 8M6X1-20mm Square Head Bolts 3# 8 M6 Nylon Lock Nuts
2# 8M6 Large Flat Washers
7 #
6 #
5 #
4 #
3 #
Customer Support: info@iboardauto.com
Rev. 20220401
3
iBoard
®
STEP 1
Start installation under the Driver Side Front Mounting Location.
Remove the large oval rubber cover located on the inner side
panel toward the front, (Fig 1). Insert (1) M8 Clip Nut into the
round hole (Fig 2). NOTE: Threaded nut must go towards the
inside of the side panel.
STEP 22
Select (1) Driver Front Mounting Bracket. Attach the Bracket to
the installed M8 Clip Nut with the included (1) M8X1.25-30mm
Hex Bolt, (1) M8 Lock Washer and (1) M8 Large Flat Washer,
(Fig 3).
Align the bottom holes in the front Bracket with the (1) hole in
the pinch weld (Fig 2). Bolt the Bracket to the pinch weld using
the included (1) M8X1.25-30mm Hex Bolt, (2) M8 Large Flat
Washers, (1) M8X1.25 Lock Washer and (1) M8 Hex Nut, (Fig
(Fig 1) Driver Side Front Mounting Location
(Fig 2) Insert M8 Clip Nut into the Round Hole
3).
NOTE: Insert the bolt up from the bottom of the pinch weld and
through the Bracket.
(Fig 3) Driver Front Mounting Bracket Installation
STEP 3
Next, move along the vehicle to the Driver Side Rear Mounting
Location, select a Driver Rear Mounting Bracket, repeat Steps
1-2 to install the rear bracket. Do not fully tighten hardware at
this time.
(Fig 4) Driver Rear Mounting Bracket Installation
Remove the Rubber
cover if equipped
(1) M8 Clip Nut
(1) M8X1.25-30mm Hex Bolt
(1) M8 Lock Washer
(1) M8 Large Flat Washer
(1) M8x1.25-25mm Hex Bolt
(2) M8 Large Flat Washers
(1) M8 Lock Washer
(1) M8X1.25 Hex Nut
(1) M8x1.25-25mm Hex Bolt
(2) M8 Large Flat Washers
(1) M8 Lock Washer
(1) M8X1.25 Hex Nut
(1) M8 Clip Nut
(1) M8X1.25-30mm Hex Bolt
(1) M8 Lock Washer
(1) M8 Large Flat Washer
The Bottom
Hole
Customer Support: info@iboardauto.com
Rev. 20220401
4
iBoard
®
STEP 4
Select a Running Board. Slip (2) M6X1-20mm Square Head
Bolts into each bottom channel (Fig 5). Carefully position the
Running Board onto the (2) Mounting Brackets. Attach the Run-
ning Board to each Mounting Bracket with (2) M6X1-20mm
Square Head Bolts, (2) M6 Large Flat Washers and (2) M6
Nylon Lock Nuts (Fig 6). Do not fully tighten at this time.
IMPORTANT: Do not slide the Running Board on the Brackets
or the bottom surface of the board will be damaged.
(Fig 5) Slip M6X1-20mm Square Head Bolts Into The Bottom
Channels
M6X1-20mm Square Head Bolts
STEP 6
Repeat Steps 1-5 for the other side Running Board installation.
The installation is completed .
Attention
Do periodic inspections to the installation to make
sure that all hardware is secure and tight.
In order to protect your bars/boards, please use mild
soap/non-abrasive products for cleaning only.
(Fig 6) Running Board Installed Onto Mounting Bracket
(2) M6X1-20mm Square Head Bolts
(2) M6 Large Flat Washers
(2) M6 Nylon Lock Nuts
STEP 5
Level and adjust the Running Board and fully tighten all hard-
ware.
Important: Please follow the recommended Tightening Tor-
ques shown in the table on page 1. Don’t over tighten, or
the nuts/bolts will be damaged.
Tabla de contenidos
Otros manuales de Accesorios para automóviles de APS
APS
APS iBoard Manual de usuario
APS
APS GR18HEC11A Manual de usuario
APS
APS iBoard IB-R296 Manual de usuario
APS
APS IA06SAG5B Manual de usuario
APS
APS iArmor IA-S926H Manual de usuario
APS
APS iBoard IB-R046 Manual de usuario
APS
APS iBoard IB-R922 Manual de usuario
APS
APS iBoard IB-R934 Manual de usuario
APS
APS iArmor Manual de usuario
APS
APS IB03DJJ7A Manual de usuario
APS
APS IB04EDJ2B Manual de usuario
APS
APS iBoard IB-R001 Manual de usuario
APS
APS iBoard IB-R159 Manual de usuario
APS
APS ELM205-V10 Manual de usuario
APS
APS iBoard IB-R921 Manual de usuario
APS
APS IA06SIB6B Manual de usuario
APS
APS IA04SBE8B Manual de usuario
APS
APS iArmor IA-S159 Manual de usuario
APS
APS iArmor IA-S022 Manual de usuario
APS
APS iBoard IB-R962 Manual de usuario
