Applied Instruments DP Plus Instrucciones de instalación y funcionamiento

Page 1of 2

Applied Instruments, Inc. • 5230 Elmwood Ave. • Indianapolis, IN USA 46203 • T (317) 782-4331 • www.appliedin.com

Application Note

03/10/2010

Installing a Dish Network Dish Pro Plus Twin (119 & 110)

system with the Super Buddysatellite meter

Connections: Output port of Dish Pro Plus twin LNBF connected to top (SIGNAL IN) port of

Super Buddy meter with coax cable.

Meter set-up

Press the SYST System soft-key (located near top left corner of LCD screen) to enter the System

Setup menu. Then select the following:

•REGION your geographic region

•SERVICE Dish Network

•SYSTEM Dish Pro Plus

•LNB MODEL DP Plus/Twin

•SWITCH TYPE DpPlus

To make selections, arrow up or down to the item to change and press Enter, then arrow up or

down to the desired option and press Enter. Press EXIT or DONE to return to Run Mode

Antenna Pointing

Install the mast plumb, preset the antenna vertical angle and tilt/skew, mount to mast and grossly

align azimuth. You may want to use the ZIP zip code look-up feature to obtain rough antenna

settings (magnetic compass heading, elevation, and tilt/skew).

After completing the System Setup:

1) Press DONE or EXIT to return to the main Run screen.

2) Adjust the tilt/skew of the dish based on the parameters provided by the Super Buddy’s

zip code lookup feature (ZIP soft-key on main Run screen).

3) Connect a coax jumper cable from the top (Signal-In) port of your Super Buddy meter to

the LNBF output port.

4) Press the LNB soft-key to apply power to the LNB. LNB1 is for the 119 satellite. Adjust

the azimuth and elevation of the dish to maximize the signal level (left bar graph), signal

quality (right bar graph), and LOCK on the 119 satellite.

5) Press the ID soft key to verify the satellite. “ID VERIFIED” means you are pointed

correctly at the 119 satellite. If ID fails, press SCAN soft-key and Super Buddy will find

the satellite you are aimed at.

6) Then press the LNB soft-key a 2nd time. LNB2 is for the 110 satellite. Adjust the tilt/skew

of the dish to maximize the signal level (left bar graph), signal quality (right bar graph),

and LOCK on the 119 satellite.You may also have to slightly adjust the azimuth and

elevation of the dish.

7) Press the ID soft key to verify the satellite. “ID VERIFIED” means you are pointed

correctly at the 110satellite. If ID fails, press SCAN soft-key and Super Buddy will find

the satellite you are aimed at.

This will ensure good signal reception from both the 119 & 110 satellites if your pole is plumb.

Page 2of 2

Applied Instruments, Inc. • 5230 Elmwood Ave. • Indianapolis, IN USA 46203 • T (317) 782-4331 • www.appliedin.com

Other Notes:

-It is NOT recommended to keep Super Buddy meter in line while checking receiver status due to

attenuation from our circuitry.

Please ensure that you have the latest versions of North American Field Guide, Software, and

USA Zip Codes loaded into your meter. If your meter has older versions loaded, please use the

FlashUpdate program to update your meter, as described in the Operations Manual.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de Applied Instruments

Applied Instruments

Applied Instruments DIRECTV SWM SL5s Instrucciones de instalación y funcionamiento

Applied Instruments

Applied Instruments NPRT 2200 Manual de usuario

Applied Instruments

Applied Instruments Super Buddy Manual de usuario

Applied Instruments

Applied Instruments Sat Buddy Manual de usuario

Applied Instruments

Applied Instruments XR-3 Instrucciones de instalación y funcionamiento

Applied Instruments

Applied Instruments T12 LO-11300 Instrucciones de instalación y funcionamiento

Applied Instruments

Applied Instruments AI Turbo S2 Manual de usuario

Applied Instruments

Applied Instruments Dual Buddy Manual de usuario

Applied Instruments

Applied Instruments XR-3 Manual de usuario

Applied Instruments

Applied Instruments Super Buddy Signal Level Meter Instrucciones de instalación y funcionamiento

Applied Instruments

Applied Instruments Super Buddy 1000.4 East Instrucciones de instalación y funcionamiento

Applied Instruments

Applied Instruments Sat Buddy 2 Manual de usuario

Applied Instruments

Applied Instruments DIRECTV SWM SL5S KaKu Instrucciones de instalación y funcionamiento

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario