Apollo Saturn Series Documento técnico

I401500

INSTALLATION, OPERATION AND MAINTENANCE GUIDE

For Saturn Series Ball Valves

P.O. BOX 125 PAGELAND, S.C. 29728 803-672-6161

Ball Valve Division

****CAUTION****

BEFORE INSTALLATION: Ensure that the component materials of the valve being

installed are compatible with the media, with regard to corrosiveness, pressure, and

temperature.

THREADED END INSTALLATION

1. Pipe connections to be threaded into these valves should be accurately threaded,

clean and free of dirt and metal shavings.

2. Teflon tape is recommended for use as the pipe joint sealant. This material should

be applied to the manufacturer’s specifications.

3. Apply wrench on the hex pads nearest the joint being tightened to any distortion of

the valve body.

SOLDER END INSTALLATION

1. Piping connections to be soldered into these valves should be cut square and then

cleaned with an appropriate cleaner or flux.

2. These valves are designed to be soft soldered. Apply heat with the flame directed

AWAY from the center of the valve body. Excessive heat can harm the Teflon seats.

Solder valves only in the fully open position.

OPERATION

Lever rotation is clockwise for “OFF” and counterclockwise for “ON”. Use only sufficient

force to open valve without damage to stops.

NOTE: Valves must be installed in piping systems that comply to the applicable

A.N.S.I. B31 Standard. Special considerations must be taken with respect to

pipe line expansions and contractions and the media expansions and

contractions within the piping system.

MAINTENANCE

Normal stem packing wear can be compensated for by tightening the packing gland nut

(except 91-200 Series). If all of the adjustment to the packing gland nut has been

made, remove the lever and packing gland nut and add one or two replacement

bearings on top of the old packing. Reassemble the lever and packing gland nut.

General repair of the valve can be made by:

1. Close valve.

2. Remove retainer by turning clockwise.*

3. Pry out the top seat, being careful not to damage the ball.

4. Push ball out of body with finger.

5. Remove packing gland nut by turning counterclockwise and push stem down into

body to remove.

6. Remove all seats and seals. To facilitate removal of the stem packing, cut with

knife.

7. Replace all seats and seals as furnished in the Service Kit. Inspect the ball and

stem for excessive wear or damage and replace if necessary.

8. Reverse the above procedure to reassemble using an anaerobic sealant on the

retainer threads. NOTE: VALVES IN OXYGEN SERVICE CAN ONLY BE SEALED

WITH A COMPATIBLE SEALANT.

* A suitable tool for removing the retainer can be made from a square piece of steel by

using the dimensions shown below.

VALVE SIZE

1/2

3/4

1-1/4

1-1/2

STEEL SIZE

5/16

13/32

1/2

5/8

3/4

15/16

1. LEVER SCREW OR NUT

2. LEVER & GRIP ASSEMBLY

3. PACKING GLAND NUT

4. STEM (Blow-Out-Proof Type)

5. STEM PACKING

6. VALVE BODY

7. SEAT

8. BALL

9. RETAINER

10. STEM BEARING

11. “O”-RING

12. PACKING GLAND

Tabla de contenidos

Otros manuales de Unidad de control de Apollo

Apollo

Apollo ApolloPress APL77V10711 Manual del propietario

Apollo

Apollo SOTERIA UL Manual de usuario

Apollo

Apollo DCLF4AN Manual de instrucciones

Apollo

Apollo 40-300 Series (1/2") Manual de instrucciones

Apollo

Apollo 55000-852 Manual de usuario

Apollo

Apollo 55000-852 Manual de usuario

Apollo

Apollo 55000-849 Manual de usuario

Apollo

Apollo RP4A Manual de instrucciones

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario