Apera DJS-0.1-C Manual de usuario

Tabla de contenidos

Otros manuales de Instrumento de medición de Apera

Apera

Apera ORP60 Manual de usuario

Apera

Apera EC60 Manual de usuario

Apera

Apera 201DJ-C Manual de usuario

Apera

Apera EC400S Manual de usuario

Apera

Apera PH400S Manual de usuario

Apera

Apera 201DJ-C Manual de usuario

Apera

Apera PH60S Manual de usuario

Apera

Apera PC60 Manual de usuario

Apera

Apera PC60-Z Manual de usuario

Apera

Apera 2310T-S Manual de usuario

Apera

Apera 2401-C Manual de usuario

Apera

Apera TDS20 Manual de usuario

Apera

Apera SX811-BR Manual de usuario

Apera

Apera LabSen 371 Manual de usuario

Apera

Apera PC60-Z Manual de usuario

Apera

Apera LabSen 232 Manual de usuario

Apera

Apera PC60-Z Manual de usuario

Apera

Apera SX811-SS Manual de usuario

Apera

Apera TN400 Manual de usuario

Apera

Apera EC60 Manual de usuario

Apera

Apera LabSen AI3102 Manual de usuario

Apera

Apera 201DJ-C Manual de usuario

Apera

Apera ORP60-Z Manual de usuario

Apera

Apera 2310T-F Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario

DJS-0.1-C Conductivity Electrode Instruction Manual

Model

Cell

constant

Electrode

size

Dimension

size

Socket

Electrode

body

Cable

length

Range

DJS-0.1-C

0.1

7×18mm

platinum

Φ12×155

BNC

Glass

1m

(0-200)

µS/cm

Use and maintenance:

1.1 Connect the DHS-0.1-C conductivity electrode to your conductivity meter. Set the cell constant

to 0.1. Then calibrate the meter in the lower calibration point (e.g. 84 µS/cm).

1.2 Keep the conductivity electrode clean, before and after the measurement, rinse the electrode

with deionized water/distilled water. In order to maintain the highest measurement accuracy, we

recommend rinsing the electrode several times with your test sample solution.

1.3 A Flow cell (included) is recommended when testing ultra-low conductivity solutions like ultra-

pure water. It helps reduce the influence from contact with air and minimizes reading error. Use

a rubber tube (7mm in diameter, not included) to connect your water source on the low end of

the flow cell. When water flows through the glass cell, conductivity can be measured without air.

1.4 How to clean a conductivity electrode:

(a) Use warm detergent water or alcohol to clean off organic contaminants on the electrode.

(b) Use 10% lemon acid to clean calcium and magnesium sediments.

1.5 Conductivity electrode storage: Store dry when not in use.

Limited Warranty

We warrant this electrode to be free from defects in material and workmanship and agrees to repair

or replace free of charge, at option of APERA INSTRUMENTS, any malfunctioned or damaged product

attributable to responsibility of APERA INSTRUMENTS for a period of six months. Warranty period

is the time limit to provide free service for the products purchased by customers, not the service life

of the tester or electrodes.

This limited warranty does not cover any damages due to:

•transportation;

•storage;

•improper use;

•failure to follow the product instructions or to perform any preventive maintenance;

•combination or use with any products, materials, processes, systems or other matter

notprovided or authorized in writing by us;

•unauthorized repair;

•normal wear and tear; or

•external causes such as accidents, abuse, or other actions or events beyond our reasonable

control.

APERA INSTRUMENTS (Europe) GmbH | Wilhelm-Muthmann-Str.18, 42329 Wuppertal, Germany

info@aperainst.de | www.aperainst.de | Tel.: +49 202 51988998