APART AUDIOSYSTEM8.8 Manual de usuario
AUDIOSYSTEM8.8
Instruction manual
Instruction manual
AUDIOSYSTEM8.8
3
AUDIOSYSTEM8.8
4
Matrix systems
Safety information
• Please check the carton box for any kind of damage on
reception of the goods. In case of a damaged carton, please
contact your dealer before opening the carton.
• !!!! Danger !!!! Exposure to high sound levels may cause a
permanent hearing loss. Individuals vary considerably to sound
pressure level induced hearing loss but nearly everyone will
lose some hearing if exposed to high sound pressure levels
for a sufficient amount of time. Therefore it is recommended
that all persons exposed to equipment capable of producing
high sound pressure levels, such as this device, be protected by
hearing protection while installing or operating this unit.
• Read all documentation before operating your equipment.
• Keep all documentation for future reference.
• Save the carton and packing material even if the equipment has
arrived in good condition.
• Should you ever need to ship the unit, use only the original
factory packing.
• Do not spill water or other liquids into or on the unit.
• Make sure power outlets are conform to the power
requirements listed on the back of the unit.
• Do not use the unit if the electrical power cord is frayed or
broken.
• Always operate the unit with the AC ground wire connected to
the electrical system ground.
• Do not connect the inputs / outputs of amplifiers or consoles
to any other voltage source, such as a battery, mains source, or
Instruction manual
AUDIOSYSTEM8.8
5
power supply, regardless of whether the amplifier or console is
turned on or off.
• Power down & disconnect units from mains voltage before
making connections.
• Do not use the unit near stoves, heat registers, radiators, or
other heat producing devices.
• Do not operate equipment on a surface or in an environment
which may distort the normal flow of air around the unit. If the
unit is used in an extremely dusty or smoky environment, the
unit should be periodically “blown free” of dust.
• Do not remove the cover. Removing the cover will expose you
to potentially dangerous voltages.
• Do not drive the inputs with a signal level higher than that
required to drive equipment to full output.
• Do not run the output of any amplifier back into another input.
• In case of mal-function this device should be serviced by
qualified service personnel only.
• The apparatus may not be exposed to dripping or splashing and
no objects filled with liquids may be placed on the apparatus.
• The appliance coupler has to be readily operable to disconnect
the device.
6
Matrix systems
CAUTION: a clipped or distorted audio signal at the input (overload)
will come out as a clipped or distorted signal at the output,
regardless of the output level and DSP processing power applied
to the signal. Clipping occurs when the signal and/or the applied
gain is too high, due to incompatibility of the signal level, a faulty
source, an impedance mismatch or a human error. Therefore,
monitor incoming signals and do not overload the inputs. Adjust
the output level(s) and gain settings of your source(s) if necessary.
Due to the internal gain structure of the AUDIOSYSTEM, the output
signals may clip even when the input signals are relatively low. Do
not over amplify audio signals. Boosting certain frequency bands or
over compressing incoming audio signals may cause signal clipping,
distortion and excessive noise at the output. If you have to add lots
of gain, your incoming signal may be too weak.
NOTE: This is the out-of-the-box manual of your AUDIOSYSTEM8.8.
A full manual and GUI guide can be found on our website. If you
want customized configurations, adjustments and a total solution
for your specific application, please seek the online manual.
The apart-team hopes you enjoy our product. We enjoyed
developing this product and guarantee it will serve as a solution for
every kind of implementation.
CAUTION
TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER OR BACK
NO USER-SERVICEABLE PARTS INSIDE
SERVICING ONLY FOR QUALIFIED PERSONNEL
Caution
Instruction manual
AUDIOSYSTEM8.8
7
AUDIOSYSTEM8.8 is an audio matrix with 4 stereo line inputs, 4
stereo D-class amplified outputs and 2 stereo line outputs (copies
of amplified outputs). The AUDIOSYSTEM8.8 also has 4 stereo FM
RDS tuners built-in. Together with this the AUDIOSYSTEM8.8 has a
paging input and an emergency mute.
The unit may be controlled through our DIWAC wall panels and has
a built-in webserver for TCP/IP connection for system integration
and/or control through any mobile device or computer that has a
web browser installed.
General Description
8
Matrix systems
• Internal webserver GUI for configuration and use
• TCP/IP
• Fixed architecture
• Stand alone operation
• Online upgradeable firmware
• Configurable mono/stereo zones
• 4 stereo unbalanced line inputs using RCA connectors
• 2 stereo unbalanced line outputs using RCA connectors
• 8 x 30 watts class-D amplifier outputs (6 - 8 ohms)
• Up to 8 DIWAC wall controls (maximum 2 controls per output
zone)
• LED display for zone status overview
• Import / export function
• 8 integrated chimes
• Universal integrated switching power supply: 85-264 Vac /
47-63 Hz
• Removable 19” rack ears
Features
Instruction manual
AUDIOSYSTEM8.8
9
Out of box behavior
• 4 stereo inputs: AUX1 (1A & 1B), AUX2 (2A & 2B), AUX3
(3A & 3B) and AUX4 (4A & 4B).
• 4 stereo outputs: output 1 (1A & 1B), output 2 (2A &
2B), output 3 (3A & 3B) and output 4 (4A & 4B).
• Pushbuttons for source selection (AUX 1 - 4) and
+- for volume control (0 - 50).
• DIWAC 1A - 1B for output 1, 2A - 2B for output 2,
3A - 3B for output 3 and 4A - 4B for output 4
• Out of the box there are no FM presets configured but
they may be accessed and configured through the control
menu. The control menu in accessed by pressing +.
In the control menu it is possible to set EQ settings, set
default settings and do an FM scan.
Standard factory configuration:
Input Configuration:
Output Configuration:
Wall panel(DIWAC) configuration:
10
Matrix systems
1
2
3
4
Otros manuales para AUDIOSYSTEM8.8
1
Tabla de contenidos
Otros manuales de Amplificador de APART
APART
APART REVAMP4240T Manual de usuario
APART
APART CHAMP-3D Manual de usuario
APART
APART REVAMP2060T Manual de usuario
APART
APART PA8250 Manual de usuario
APART
APART REVAMP1120T Manual de usuario
APART
APART MA200 Manual de usuario
APART
APART PIR7600 Manual de usuario
APART
APART Champ-2 Manual de usuario
APART
APART vinci 2125 Manual de usuario
APART
APART Champ-One Manual de usuario
APART
APART REVAMP4100 Manual de usuario
APART
APART MA-35 Manual de usuario
APART
APART PM7400 MKII Manual de usuario
APART
APART concept1t Manual de usuario
APART
APART MA-65 Manual de usuario
APART
APART REVAMP4120T Manual de usuario
APART
APART PM1122 Manual de usuario
APART
APART MA246 Manual de usuario
APART
APART Concept 1T Manual de usuario
APART
APART CONCEPT1 Manual de usuario
