Aosom BENTLEY BACALAR Manual de usuario
BATTERY POWERED RIDE-ON
Owner’s Manual
with Assembly Instructions
Styles and colo(u)rs may vary.
Made in China.
The owner’s manual contains important safety information as well as assembly, use and
maintenance instructions.
The Ride-on Car must be assembled by an adult who has read and understands the
instructions in this manual.
Keep the package away from children and dispose of properly before use.
Keep this manual for future reference.
BENTLEY BACALAR
Officially
Licensed Product
IN230600438V01_US_CA
370-293V80
Battery
Charger
12V4.5AH *1
12V500mA
Suitable age:
Load Capacity:
Speed:
Size of ride-on car:
Power way:
Charge time:
37-96 months
Under 30kg
3-5km/h
108 * 65 * 45 CM
Charging type
8-12 hours
About Your New Ride-On │1
VER: SMS-JE1008-EN-20230224
SPECIFICATIONS:
On the purchase of your new Ride-On.
This ride-on will provide your child with many miles of riding enjoyment. To
help ensure a safe ride we ask you to please read this manual carefully, and
keep it for future reference.
Please follow the recommendations in this manual, they are designed to
improve the safety and operation of your ride-on car and it’s rider.
Made by Zhejiang Jiajia Ride-On Co., Ltd in China under license
from Bentley Motors Limited.
User Notice │2
The following safety hazards may result in serious injury or death:
• Never leave child unattended. Direct adult supervision is required. Always keep child in view
when child is in vehicle.
• To reduce the risk of injury, adult supervision is required. Never use in roadways, near motor
vehicles, on or near steep inclines or steps, swimming pools or other bodies of water, always
wear shoes, and never allow more than 1 rider.
• Never use in unsafe conditions such as snow, rain, loose dirt, mud, sand, or gravel,
otherwise may result in an unexpected accident such as tipping over, and could damage the
electrical system or battery
• Not to be used in traffic.
• This toy should be used with caution since skill is required to avoid falls or collisions causing
injury to the user or third parties.
• This toy is unsuitable for children under 36 months due to its maximum speed; Maximum
user weight is 30kg.
• This toy has no brake.
WARNING!
SAFETY
●Non-rechargeable batteries are not to be recharged.
●Rechargeable batteries are to be removed from the toy before being charged.
●Rechargeable batteries are only to be charged under adult supervision.
●Different types of batteries or new and used batteries are not to be mixed.
●Batteries are to be inserted with the correct polarity.
●Exhausted batteries are to be removed from the toy.
●The supply terminals are not to be short-circuited.
BATTERY INFORMATION
• CHOKING HAZARD - Small parts. Not suitable for children under 36 months. The product
contains small parts, keep children away when assembling.
• ADULT ASSEMBLY REQUIRED.
• Always remove protective material and poly bags and dispose before
assembly.
• Protective equipment should be worn. Always wear shoes and sit in the seat when operating
the vehicle.
• Only drive on level ground. Never use on the lawn.
• Never leave a child unattended.
• Keep your hands, hair, and clothes away from moving parts.
1
5
6
5
6
7
9
12
7
8
2
10 11
2
2
3
413
3
15
16
14
HINT: Some parts shown are assembled on both sides of vehicle
Assembly tools required
(not included):
Screwdriver
Parts Diagram │3
A B C
D E F
G H I
A K L
M N O
P
Vehicle body x1 Ø10 washer x1 Wheel x4
Wheel driver x2 Lock nut x4 Hubcap x4
Side mirror x2 Windshield x1 Steering wheel x1
M5x30 machine screw x1 Ø5 nut x1 Seat x1
Ø4x16 screw x3 Spanner x1 Charger x1
Remote controller x1
Parts List │4
1
2
3
4
5
6
Attach the Rear Wheels │5
Remove all the parts from the rear axle.
1-2. Fit the wheel driver to the wheel. Insert and tigthen three Ø4x16 screws to secure
the wheel driver to the wheel.
3. Slide the wheel onto the rear axle (Left Side). Keep the wheel driver match up with
the gear box on the rear axle.
4. Slide a Ø10 washer onto the rear axle.
5. Tighten a lock nut to the end of the rear axle with a spanner.
Repeat the above procedure to assemble the other Rear Wheel.
HINT: An extra spanner has been provided to hold the Lock Nut on the other side of the
rear axle while tightening the Lock Nut on the other side.
6. Fit the hub caps to the wheels.
Rear Bottom View
Rear gear boxesRear gear boxes
43
2
1
5
Attach the Front Wheels │6
Remove all the parts from the front axle.
1. Slide a Ø10 washer onto the front axle.
2. Slide a wheel onto the front alxe.
3. Slide a Ø10 washer onto the front axle.
4. Tighten a lock nut to the end of the front axle with a spanner. DO NOT over tighten.
5. “Snap” the hubcap to the wheel.
Repeat the above procedure to assemble the other Front Wheel.
GAP
After assembling any wheel to the axles, please check the gap
between the screw thread and the collapsible (refer to below
picture), if the gap is too big, please add two or three washers
inside the wheel, but after tightening the nut outside the wheel,
please turn the wheel by your finger to check if the wheel can run
smoothly, this is very important, because if the wheel can run
smoothly, it is ok, but if the nut press the wheel and the wheel
can’t run smoothly, the motor will be broken easily! Then you need
to decrease one or two washers to make sure the wheel can run
smoothly!
Front Bottom View
2
4
3
5
7
6
1
Attach the Steering Wheel │7
Remove the M5x30 machine screw and Ø5 nut from the steering wheel.
Turn the vehicle body upright.
5. Place the steering wheel over the the steering column, protruding from the middle of
1. With a screwdriver loosen the
screw on the battery cover located
in the center of the steering wheel.
2. Remove the battery cover from the
top of the battery compartment.
3. Insert 2x1.5 AA batteries in their
correct polarities.
4. Place the battery cover over the
battery compartment and fasten
with the screw you loosened in
step one.
Attach the Steering Wheel
HINT: If the steering wheel of your vehicle equipped with the sound function, please
follow the steps 1-4 to add the batteries (Not Included), and refer to the battery
information on page 2.
the steering wheel base.
6. Align the holes on each side of steering
End of steering column
wheel with the holes at the end
of the steering column.
7. Fasten a nut on the opposite end
of the screw to secure the
steering wheel to the steering
column.
1
2
Attach the Windshield & Side Mirrors │8
1. Fit the tabs windshield into the grooves on the vehicle. Press until you hear it “click”
into place.
2. Fit the side mirrors to the holes on the both doors, push until you hear them “click”
into place.
2
1
3
Connect the Power Supply & Attach the Seat │9
1. Plug the vehicle connector into the connector on the battery.
2. Fit the tabs on the seat back into the grooves on the rear of the vehicle.
3. With a screwdriver tighten the M5x16 screws on the top of the seat into the holes in
the vehicle.
Tabs on seat back
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Idiomas:
Otros manuales de Coche de juguete motorizado de Aosom
Aosom
Aosom 370-189V80 Manual de usuario
Aosom
Aosom 370-082 Manual de usuario
Aosom
Aosom 370-172V80 Manual de usuario
Aosom
Aosom 370-066 Manual de usuario
Aosom
Aosom CHILDREN'S Pedal Engineering Vehicle Manual de usuario
Aosom
Aosom Lambo V12 Vision Gran Turismo Manual de usuario
Aosom
Aosom 370-283V80 Manual de usuario
Aosom
Aosom 370-301V80 Manual de usuario
Aosom
Aosom 370-218V80 Manual de usuario
Aosom
Aosom 370-109V80 Manual de usuario
Aosom
Aosom 370-287V80 Manual de usuario
Aosom
Aosom 370-196 Manual de usuario
Aosom
Aosom 370-245V00 Manual de usuario
Aosom
Aosom 370-168V80 Manual de usuario
Aosom
Aosom Mercedes-Benz SLC 300 Final Edition... Manual de usuario
Aosom
Aosom 370-149V80 Manual de usuario
Aosom
Aosom 370-259V00 Manual de usuario
Aosom
Aosom 370-282V80 Manual de usuario
Aosom
Aosom 370-141V80 Manual de usuario
Aosom
Aosom 370-159V80 Manual de usuario
