Antrax AlarmBox-wireless Manual de usuario
antrax Datentechnik GmbH
[email protected] - www.antrax.de
AlarmBox-wireless, Type GSM
230V-Box with integrated GSM module and temperature sensor
Manual
11.04.2014
- 1 -
Hasenbrink 4 32052 Herford Germany Tel. +49 (0) 5221 929660 Fax +49 (0) 5221 9296628
antrax Datentechnik GmbH
[email protected] - www.antrax.de
Content
General
Using the AlarmBox-GSM
Safety Instructions
Scope of Delivery
Hardware
Software
System Requirements
Technical Features
G eneral
Load Circuit
GSM
CE-Marking
Installation
Hardware
Handling
ON-LED Blink Codes
GSM
Getting Started
Parameters
Blink Codes
Controlling the AlarmBox-GSM via Voice-Call
Controlling the AlarmBox-GSM via SMS
Alarming
Quick Introduction
Controlling the AlarmBox-GSM via Landline or Mobile Phone
Troubleshooting
Terminology
- 2 -
Hasenbrink 4 32052 Herford Germany Tel. +49 (0) 5221 929660 Fax +49 (0) 5221 9296628
antrax Datentechnik GmbH
[email protected] - www.antrax.de
General
The AlarmBox-wireless, Model GSM allows monitoring of the temperature (via temperature
sensor) and the 230V supply voltage. Exceeded or fallen below the pre-set temperature limits or a
power supply failure the alarm can be sent over a voice-call ("normal" phone call from the box) or
via a text message (SMS) from the box.
Also the AlarmBox-wireless, Model GSM allows to remotely switch ON and OFF a 230V electrical
appliance over a voice-call ("normal" phone call call to the box) or via text message (SMS) to the
the box.
Before first use please read this instruction manual carefully. It contains information for the correct
use and contains important tips for the installation of the AlarmBox-wireless, Type GSM
(hereafter called AlarmBox-GSM). The manufacturer does not accept any liability due to improper
use of the unit. In this case all guarantee claims are invalid.
U sing the Alarm Box-GSM
Die AlarmBox-GSM is designed for monitoring of
temperature (-35°C to 75°C)
and
230V power supply
and the switching of
resistive loads i. e. electric bulbs or heating fans
or
inductive loads i. e. electric motors or transformers to a maximum consumption of
2000W (230V / 8 7A)
in dry closed residential rooms and offices. Rules and Regulations governing the connection and
use of electronic devices and their security regulations must be followed.
- 3 -
Hasenbrink 4 32052 Herford Germany Tel. +49 (0) 5221 929660 Fax +49 (0) 5221 9296628
antrax Datentechnik GmbH
[email protected] - www.antrax.de
Safety Instructions
Do not open the AlarmBox-GSM. It contains no parts to be serviced by you.
Only use the AlarmBox-GSM indoors and do not subject the unit to moisture or humidity.
Also use the temperature sensor without the influence of humidity.
Only connect the AlarmBox-GSM to properly installed 230V AC outlets and power strips.
Only clean the exterior of the AlarmBox-GSM with a dry cloth after unplugging it from the
electrical outlet and removal of the interface cable.
Do not overload the AlarmBox-GSM above its load specification level. An overload can
lead to the AlarmBox-GSM being destroyed.
Do not use the AlarmBox-GSM within the reach of children.
Do not use the AlarmBox-GSM if one or several parts (case cable plug temperature
sensor) are damaged or damage may be caused by its location (e.g. falling down).
Repairs to the AlarmBox-GSM can only be performed by authorized personnel.
Only connect electrical appliances that have no limit to their switched-on time (i.e. all
connected electrical appliances must be able to take continuous current without sustaining
damage in the case of a default to the permanently "ON" position.).
Caution:
Safety Instruction for the wireless module:
The AlarmBox-GSM contains a mobile component like the ones used in mobile phones. Thus in
principle all safety instructions and precautions apply as with the use of mobile phones in particular
are the following:
Do not use the AlarmBox-GSM in the vicinity of medical devices such as hearing aids or
cardiac pacemakers. Functioning of these devices could be disturbed.
The AlarmBox-GSM may be operated in the vicinity of for example TV sets radios or PCs
however but could cause disturbances in operation.
If an external mobile antenna is connected the above mentioned information shall apply
accordingly for this antenna.
The AlarmBox-GSM is designed for stationary use not for use in vehicles of all kinds.
- 4 -
Hasenbrink 4 32052 Herford Germany Tel. +49 (0) 5221 929660 Fax +49 (0) 5221 9296628
antrax Datentechnik GmbH
[email protected] - www.antrax.de
Deliver
Hardware
Everything there? The delivery of a AlarmBox-GSM unit contains:
the AlarmBox-GSM incl. temperature sensor (whit approx. 2m connector cable)
this manual
Software
Software is not required for the control of the AlarmBox-GSM
S stem Requirements
General
SIM card (pre-paid or contract)
- 5 -
Hasenbrink 4 32052 Herford Germany Tel. +49 (0) 5221 929660 Fax +49 (0) 5221 9296628
antrax Datentechnik GmbH
[email protected] - www.antrax.de
Technical Features
General
Operating voltage: 230/240V~ 50/60Hz
Protection class: IP20 for dry rooms only
Connector system: SCHUKO
The current switching status is indicated by a green LED (labelled "ON")
The current GSM status is indicated by a red/green LED (labelled "GSM")
Load and control circuits have a safe electrical separation
Ambient temperature: 0 ... +40°C
Storage temperature: 10 ... +70°C
Temperature Sensor
Cable length: approx. 2m
Measuring temperature: -35 … +75°C
Load Circuit
Operating voltage: 230/240V~ 50/60Hz
Single-pole load switch (Relay)
Maximum switching capacity:
-Resistance loads i.e. electric light bulbs or heating fans up to 2000 W (230 V / 8.7A)
(8 7A at 230/240V)
-Inductive loads i.e. electric motors and transformers up to 2000W (8 7A at 230/240V)
GSM
Integrated GSM-Module: Telit GE865-QUAD
Aerial connector: SMA
Use with pre-paid or contract SIM cards of all providers no SIM lock!
CE Marking
In accordance with the Low Current and EMV Guidelines.
- 6 -
Hasenbrink 4 32052 Herford Germany Tel. +49 (0) 5221 929660 Fax +49 (0) 5221 9296628
antrax Datentechnik GmbH
[email protected] - www.antrax.de
Installation
Hardware
Insert the 230V plug of the device to be monitored by the AlarmBox-GSM into the socket
of the AlarmBox-GSM
Insert the AlarmBox-GSM into a 230V outlet socket
CAUTION: after inserting the AlarmBox-GSM socket the connected device is switched ON
or OFF depending on the previous set state
place the temperature sensor where the temperature shall be monitored
the socket of the AlarmBox-GSM can be switched (''toggled'') by pressing the push-button
(at the bottom of the box) for 3 seconds at least
Operation
The AlarmBox-GSM is operated solely via SMS commands a voice call or via the push-button (at
the bottom of the box).
Blinc codes of the ON-LED
The ON-LED signals the current state of the AlarmBox-GSM. It signals whether an existing alarm
has already been reported. In case of alarm and the deposited alarm phone number has not been
reached yet the ON-LED blinks (depending on the alarm type) as described below. If the alarm
situation has been resolved successfully the ON-LED signals the current state of the socket.
ON-LED Meaning
Permanently OFF Socket OFF
Permanent ON Socket ON
1 x red The set temperature limits have fallen below or have
been exceeded
2 x red Socket in reset mode
3 x red The supply voltage has failed
4 x red The temperature sensor is defect
- 7 -
Hasenbrink 4 32052 Herford Germany Tel. +49 (0) 5221 929660 Fax +49 (0) 5221 9296628
antrax Datentechnik GmbH
[email protected] - www.antrax.de
Button
Keeping the button pressed for more than 3 seconds the state of the socket is being ''toggled'. The
socket is either ''ON'' or ''OFF'' when the button is pressed. The ON-LED indicates the current state
of the socket.
- 8 -
Hasenbrink 4 32052 Herford Germany Tel. +49 (0) 5221 929660 Fax +49 (0) 5221 9296628
antrax Datentechnik GmbH
[email protected] - www.antrax.de
GSM
Getting Started
Parameter on the SIM card
The SIM card intended for the us with the AlarmBox-GSM can be prepared with any mobile phone
or PC SIM card reader.
The prepared SIM card should be inserted into the small slot on
the underside of the AlarmBox-GSM. The SIM card must be
inserted using a small tool (screwdriver or similar) and be
carefully pushed right up to the mechanical rear stop where it will
lock in this position. To later extract the SIM card it must be
pressed in again to the rear stop and then released. It will be
ejected by the push-pull card reader mechanism.
ACHTUNG: Before inserting/removing the SIM card ensure the AlarmBox-GSM is not connected
to the power supply (i.e. pull out of the wall outlet) otherwise the complete contents of the SIM
card not only the contents of the phone book could be destroyed. In this instance the SIM card
user will need to exchange the card with the provider which will incur further costs.
Standard-PIN:
As a general rule the use of a SIM card requires user to identify himself / herself with the PIN code.
The "AlarmBox-GSM" tries (if no PIN changes have been made) to log itself on using the standard
PIN code – please therefore use the standard PIN given below when first initialising SIM card.
The PIN is the access code for a SIM card. The AlarmBox-GSM expects the standard
PIN code '1357' to be used initially. This PIN code can be pre-set on the SIM card with
the help of a mobile phone or PC SIM card readers.
(Error code 2 see also Troubleshooting)
- 9 -
Hasenbrink 4 32052 Herford Germany Tel. +49 (0) 5221 929660 Fax +49 (0) 5221 9296628
antrax Datentechnik GmbH
[email protected] - www.antrax.de
GSM
Blinc codes of the GSM-LED:
The AlarmBox-GSM uses different flashing codes of the "GSM" LED to indicate the current
condition of the "GSM" module. If the "GSM" LED emits one of the flashing codes for an extended
period of time there may be an error as described below.
Basically the flashing codes are generated at each Power ON and during each GSM network login.
Normally however the individual error states are so short that the single Flashing Codes are not
perceivable. (e.g. the Flashing Code 2 during PIN setting lasts only approx. 0.3 second)..
GSM-
LED
Description If permanentl displa ed
1 x red Test of the GSM module Serious Basic Error. The GSM module is
probably defective
2 x red Initial Settings SIM card is not inserted or is defective the PIN
code is wrong or entry of the PUK is necessary
(see also Troubleshooting)
(CAUTION: Please check the PIN code on the
SIM card. If it is wrong further login attempts
can lead to the SIM card being blocked. (only 3
attempts are possible!)
3 x red Waiting to login to the GSM
network
No GSM network available (see also
Troubleshooting)
4 x red Enter GSM-Module
parameters
The entry "Own Phone Number" on the SIM
card is missing or the GSM module is damaged
6 x red No credit on the SIM Card (pre-paid SIM Card)
static
green
AlarmBox-GSM is registered (logged in) and ready to use
flashing
yellow
AlarmBox-GSM is receiving a voice call marks the ringing time and the whole
time of the connection(= during the complete call)
- 10 -
Hasenbrink 4 32052 Herford Germany Tel. +49 (0) 5221 929660 Fax +49 (0) 5221 9296628
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Manuales populares de Sistema de seguridad de otras marcas
EDM
EDM Solution 6+6 Wireless-AE Manual de usuario
Highway Safety Group
Highway Safety Group EA401 Manual de usuario
Siren
Siren LED GSM Manual de usuario
Detection Systems
Detection Systems 7090i Instrucciones de montaje
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Manual de usuario
Siemens
Siemens FDM273 Manual de usuario