Antari F-2 Fazer Manual de usuario

F-2 Fazer

User Manual

- ENGLISH

- 中文

- ENGLISH -

Safety Information

Please read the following safety information carefully before operating the

machine. This information includes important safeguards about

installation, usage, and maintenance. Pay attention to all warning labels

and instructions in this manual and printed on the machine.

If you have questions about how to operate the machine safely, please contact your local

Antari dealer for help.

l Keep this device dry.

l Always connect to a grounded circuit to avoid risk of electrocution.

l Before connecting the machine to power, always check the voltage indicate on the

machine matches to your local AC voltage. Do not use the machine if AC power voltage

does not match.

l Disconnect the machine from AC power before servicing and when not in use.

l If the supply cord is damaged, contact your local Antari dealer for replacement.

l This product is for indoor use only! Do not expose to rain or moisture. If fluid is spilled,

disconnect AC power and clean with a damp cloth. If fluid is spilled onto electronic parts,

immediately unplug the machine and contact your local Antari dealer for advice.

l No user serviceable and modifiable parts inside. Never try to repair this product, an

unauthorized technician may lead the machine to damage or malfunction.

l For adult use only. Children being supervised not to play with the machine. Never leave

the machine running unattended.

l The machine is not to be used by persons (including children) with reduced physical,

sensory or mental capabilities, or lack of experience and knowledge.

l Installed in a well ventilated area. Provide at least 50 cm space around the machine.

l Never add flammable liquid of any kind to the machine.

l Make sure there are no flammable materials close to the machine while operating.

l Only use Antari fluid. Other fluid may lead to heater clog and malfunction.

l If the machine fails to work, unplug the machine and stop operation immediately. Contact

your local Antari dealer for advice.

l Before transporting the machine, make sure the fluid tank is completely drained.

l Smoke fluid may present health risks if swallowed. Do not drink smoke fluid. Store it

securely. In case of eye contact or if fluid is swallowed immediately look for medical

advice.

Unpacking and Inspection

Immediately upon receiving the machine, carefully unpack the carton, check the content to

ensure that all parts are present and have been received in good condition. If any parts

appear damaged or mishandled from shipping, notify the shipper immediately and retain the

packing material for inspection.

What is included: 1 x F-2 Fazer

1 x Fluid Tank

1 x User Manual

Product Dimension

H 233.6 mm

W 380 mm

L 424.1 mm

Product Overview

Setting UP

Step 1:Place the machine on a flat surface and in a suitably large area with at least 50 cm

of open space around the machine.

Step 2: Fill the fluid tank with Antari approved fluid.

Step 3: Connect the machine to a suitably rated power supply. To determine the power

requirement for the machine, refer to the label on the back of the machine.

Always connect the machine to a protected circuit and ensure it is properly

grounded to avoid risk of electrocution.

Step 4: Turn on the machine and allow it to heat up. Heat up takes approximately 1.5

minutes. Once the machine has reached operating temperature, the LCD display will show

“Ready to Faze”. Now the machine is ready for operation.

Step 5: To start making haze, locate the Volume button on the control panel, and press the

button to start making faze.

Step 6: To t u r n -off the unit, press and hold down the Stop button for at least three seconds.

This will immediately begin the self-cleaning and shut down process. After the purging

process is complete the unit will automatically shut down and put itself in state of hibernation.

Output Nozzle

XLR 3-Pin & XLR 5-Pin

DMX Connector

LCD Display Control Panel

Power Input

Breaker

Simple press the Volume button to “wake” the unit and return it operational status.

Operation

Control Panel Operation

The machine can be operated with the onboard digital control interface located on the rear.

Button

Function

[MENU]

Scroll through setting menu

▲[UP]/[TIMER]

Up/Activate Timer function

▼ [DOWN]/[VOLUME]

Down/Activate Volume function

[STOP]

Deactivate Timer/Volume function

CONTROL MENU

Set the interval from 1 to 999 seconds

Set the duration from 1 to 999 seconds

Set the timer output from 1 to 100%

Set the output volume from 1 to 100%

Set the output volume from 20 to 100%

Interval

Set 999s

Duration

Set 999s

Timer

Out 100%

Volume

Out 100%

Fan

Out 100%

Set the DMX address from 1 to 511

Set the DMX mode Sync, 1Ch or 2Ch

Turn On/Off run last setting function

This menu functions details the current machine firmware.

DMX Connector Pin Assignment

The machine provides a 3- or 5-pin XLR connector for DMX connection. The diagram below

indicates pin assignment information.

Function

Ground

Data-

Data+

N/A

DMX Operation

Making the DMX Connection – Connect the machine to a DMX controller or to one of the

machines in the DMX chain. The machine uses a 3-pin or 5-pin XLR connector for DMX

connection, the connector are located on the front of the machine.

DMX512

Add. 511

DMX Mode

1Ch

Quick

Start OFF

Info

Ver: 1.0

DMX Channel Function

Channel Mode

Channel

Value

Function

0-5

6-255

Faze off

Faze 1-100%

6-255

Fan 20-100%

0-5

Faze off

Fan 100%

6-255

Faze 1-100%

Fan 100%

Sync

0-5

Faze Off

Fan 20%

6-255

Faze 1-100%

Fan 21 – 100%

Fluid

Only use Antari FLG water-based liquid for the F-2 Fazer. The machine is tested and

calibrated with this liquid to get the best output performance. Warranty will be voided if any

other type of liquid is used, improper use of liquid may lead to machine failure and

malfunction.

Service and Maintenance

․ Do not allow the machine to become contaminated.

․ Remove dust from the air vents with air compressor, vacuum or a soft brush.

․ Only use a damp cloth to clean the casing.

․ Before storing run distilled water through the system to help avoid condensing the pump

or heater.

․ It is recommended to run the machine on a monthly basis in order to achieve best

performance and output condition.

․ Excessive dust, liquid and dirt built up will degrade performance and cause overheating.

Error Messages

Indicates heater exceeds temperature range

Indicates heater is not working properly

If above message shows on the display, unplug the machine and stop

operation immediately. Contact your local Antari dealer for advice

Technical Specifications

Input Voltage

Power Consumption

Warm-up Time

Max. operating time

Fluid tank capacity

Fluid consumption

Compatible fluid

Control option

DMX Channels

Power connection

DMX data connection

Dimensions

Dry Weight:

US model: AC 100-120V, 50/60 Hz

EU model: AC 220-240V, 50/60 Hz

120V 1000W

240V 1500W

1.5 min. (approx.)

12 hrs max. output

5 L

6.5 ml/min (100% output)

Antari FLG water-based fluid

DMX 512, Manual

2 channels, Faze volume and fan speed

IEC

3-pin and 5-pin XLR

L 424.1 x W 380 x H 233.6 mm

14.7 kg

Heater

Overheat

Heater

Error

使用說明書

使用說明及安全注意事項

在使用機器以前，請仔細閱讀以下說明，此份說明書包含了如何在安全的情況下安

裝並使用機器，且會說明機器上所有標示的標籤所代表的意義。

如果您有任何使用上的問題，請聯繫當地的 Antari 經銷商尋求清楚的說明與協助。

l 保持機器乾燥。

l 請配合接地型插座，以避免觸電的危險。

l 使用機器前，請確定使用場所的 AC 電源規格，與機器電壓規格是否相符。

l 拔開機器和 AC 電源插座時，請確認機器已關機不在使用的狀態下。

l 如果電源線損壞，請連繫當地的 Antari 經銷商尋求說明與協助。

l 本產品僅限室內使用，請勿將機器暴露在雨中或潮濕的環境，如果有液體(煙霧水)翻倒或

溢出，請勿連接機器與 AC 電源，用乾布擦拭乾淨，如果任何液體進入機器電子零件，請

立即拔除插頭，並聯繫當地的 Antari 代理商。

l 本機器不含任何用戶拆解和自行維修或修改的零件在內，請勿嘗試自行維修或改裝機器，

未經授權的技術人員，可能導致機器故障或永久損壞。

l 機器限成人操作，請勿在無人值守時讓機器運作。

l 請勿讓身體、精神、感官存在缺陷或經驗不足者(包括兒童)使用本機器。

l 在通風良好的地方安裝使用機器，機器周邊至少應保留 50 公分的空間。

l 請勿添加任何易燃物品進入機器。

l 操作機器時請確認周邊沒有任何易燃的材料。

l 為確保機器的使用壽命，請使用 Antari 的煙霧水。使用其他品牌煙霧水可能會導致電熱管

阻塞和機器的故障，並使保固失效。

l 如果機器出現故障，請拔下機器插頭，立即停止工作。並請連繫您當地的 Antari 經銷商。

l 運送機器以前，請確認機器的油箱已經完全清空。

l 煙霧水不能食用，吞食煙霧水可能導致損壞健康的風險，請將煙霧水存放在室內安全的地

方。如果碰觸到眼睛或誤吞食，請立即尋求醫生的協助。

Tabla de contenidos

Otros manuales de Máquina de niebla de Antari

Antari

Antari W-515 Manual de usuario

Antari

Antari S-120 Manual de usuario

Antari

Antari Onboard DMX Manual de usuario

Antari

Antari F-7X Manual de usuario

Antari

Antari LCU-2S Manual de usuario

Antari

Antari Z Series Manual de usuario

Antari

Antari Fog cooler DNG-100 Manual de usuario

Antari

Antari IP-1600 Manual de usuario

Antari

Antari X FAZER Manual de usuario

Antari

Antari ICE-100 Manual de usuario

Antari

Antari Fog cooler DNG-100 Manual de usuario

Antari

Antari Z-390 Series Manual de usuario

Antari

Antari Z-800 III Manual de usuario

Antari

Antari Z-1520 RGB Manual de usuario

Antari

Antari Z-1000II Manual de usuario

Antari

Antari M-11 Manual de usuario

Antari

Antari WiFi-800 Manual de usuario

Antari

Antari M-8 Manual de usuario

Antari

Antari MOBILE MB-1 Manual de usuario

Antari

Antari FT-200 Manual de usuario

Antari

Antari X FOGGER Manual de usuario

Antari

Antari DNG250FE Manual de usuario

Antari

Antari FT-55 Manual de usuario

Antari

Antari II Series Manual de usuario

Manuales populares de Máquina de niebla de otras marcas

Boost

Boost BOOST-FOG400LED-BK Manual de usuario

Home Accents Holiday

Home Accents Holiday FM1000-ASH Manual de usuario

EuroLite

EuroLite ZEITGEIST FOG-1200 Manual de usuario

Dyna-Fog

Dyna-Fog CYCLONE ULTRA 2734 Manual de usuario

PROEL

PROEL DRAGO HEAVY PLFD150HY Manual de usuario

Sparklyn

Sparklyn Y846 Manual de usuario

Magicfx

Magicfx CO2 Gun Manual de usuario

Ibiza

Ibiza LSM500LAS Manual de usuario

Venue Lighting Effects

Venue Lighting Effects ULTRA MINI-FOGGER Manual de usuario

High End

High End F-100 Manual de usuario

Chauvet

Chauvet ARENA 2100 FLEX Manual de usuario

Beamz

Beamz F1600 Manual de usuario

Sagitter

Sagitter SG ARS900C Manual de usuario

KISANKRAFT

KISANKRAFT KK-STF-480 Manual de usuario

Orion

Orion OT-U250PP Guía

Beamz

Beamz S2500 Manual de usuario

American DJ

American DJ Dyno-Fog II Manual de usuario

JB Systems

JB Systems FX 1700 Manual de usuario