Anritsu MX269018A Manual de usuario

Document No.: M-W3555AE-22.0

ANRITSU CORPORATION

MX269018A

Analog Measurement Software/

MS2830A/MS2840A

Signal Analyzer

Analog Signal Generator

Operation Manual

22nd Edition

•For safety and warning information, please read this

manual before attempting to use the equipment.

•

Additional safety and warning information is provided

within the MS2830A Signal Analyzer Operation Manual

(Mainframe: Operation) or MS2840A Signal Analyzer

Operation Manual (Mainframe: Operation). Please also

refer to them before using the equipment.

•

Keep this manual with the equipment.

Safety Symbols

To prevent the risk of personal injury or loss related to equipment malfunction, Anritsu Corporation uses the

following safety symbols to indicate safety-related information. Ensure that you clearly understand the meanings of

the symbols BEFORE using the equipment. Some or all of the following symbols may be used on all Anritsu

equipment. In addition, there may be other labels attached to products that are not shown in the diagrams in this

manual.

Symbols used in manual

This indicates a very dangerous procedure that could result in serious injury or

death if not performed properly.

This indicates a hazardous procedure that could result in serious injury or death if

not performed properly.

This indicates a hazardous procedure or danger that could result in light-to-severe

injury, or loss related to equipment malfunction, if proper precautions are not taken.

Safety Symbols Used on Equipment and in Manual

The following safety symbols are used inside or on the equipment near operation locations to provide information

about safety items and operation precautions. Ensure that you clearly understand the meanings of the symbols and

take the necessary precautions BEFORE using the equipment.

This indicates a prohibited operation. The prohibited operation is indicated

symbolically in or near the barred circle.

This indicates an obligatory safety precaution. The obligatory operation is

indicated symbolically in or near the circle.

This indicates a warning or caution. The contents are indicated symbolically in or

near the triangle.

This indicates a note. The contents are described in the box.

These indicate that the marked part should be recycled.

MX269018A Analog Measurement Software/

MS2830A/MS2840A Signal Analyzer Analog Signal Generator

Operation Manual Operation

24 June 2011 (First Edition)

20 July 2018 (22nd Edition)

publisher.

The contents of this manual may be changed without prior notice.

Printed in Japan

DANGER

WARNING

CAUTION

For Safety

iii

CAUTION

•Never input a signal of more than the indicated value between the

measured terminal and ground. Input of an excessive signal may

damage the equipment.

Check Terminal

Equipment Certificate

Anritsu Corporation guarantees that this equipment was inspected at

shipment and meets the published specifications.

Anritsu Warranty

•During the warranty period, Anritsu Corporation will repair or exchange this

software free-of-charge if it proves defective when used as described in the

operation manual.

•The warranty period is 6 months from the purchase date.

•The warranty period after repair or exchange will remain 6 months from

the original purchase date, or 30 days from the date of repair or

exchange, depending on whichever is longer.

•This warranty does not cover damage to this software caused by Acts of

God, natural disasters, and misuse or mishandling by the customer.

In addition, this warranty is valid only for the original equipment purchaser. It

is not transferable if the equipment is resold.

Anritsu Corporation shall assume no liability for injury or financial loss of the

customer due to the use of or a failure to be able to use this equipment.

Anritsu Corporation Contact

In the event of this equipment malfunctions, contact an Anritsu Service and

Sales office. Contact information can be found on the last page of the printed

version of this manual, and is available in a separate file on the PDF version.

Notes On Export Management

This product and its manuals may require an Export License/Approval by

the Government of the product's country of origin for re

export from your

country.

Before re

exporting the product or manuals, please contact us to confirm

whet

her they are export-controlled items or not.

When you dispose of export

controlled items, the products/manuals need

to be broken/shredded so as not to be unlawfully used for military purpose.

Software End-User License Agreement (EULA)

Please read this Software End-User License Agreement (hereafter this EULA) carefully before using

(includes executing, copying, registering, etc.) this software (includes programs, databases, scenarios,

etc., used to operate, set, etc., Anritsu electronic equipment). By reading this EULA and using this

software, you are agreeing to be bound by the terms of its contents and Anritsu Corporation (hereafter

Anritsu) hereby grants you the right to use this Software with the Anritsu-specified equipment

(hereafter Equipment) for the purposes set out in this EULA.

1. Grant of License and Limitations

1. Regardless of whether this Software was

purchased from or provided free-of-charge by

Anritsu, you agree not to rent, lease, lend, or

otherwise distribute this Software to third

parties and further agree not to disassemble,

recompile, reverse engineer, modify, or create

derivative works of this Software.

2. You may make one copy of this Software for

backup purposes only.

3. You are not permitted to reverse engineer

this software.

4. This EULA allows you to install one copy of

this Software on one piece of Equipment.

2. Disclaimers

To the extent not prohibited by law, in no

event shall Anritsu be liable for personal

injury, or any incidental, special, indirect or

consequential damages whatsoever,

including, without limitation, damages for

loss of profits, loss of data, business

interruption or any other commercial

damages or losses, arising out of or related

to your use or inability to use this Software.

3. Limitation of Liability

a. If a fault (bug) is discovered in this Software,

preventing operation as described in the

operation manual or specifications whether

or not the customer uses this software as

described in the manual, Anritsu shall at its

own discretion, fix the bug, or exchange the

software, or suggest a workaround,

free-of-charge. However, notwithstanding

the above, the following items shall be

excluded from repair and warranty.

i) If this Software is deemed to be used for

purposes not described in the operation

manual or specifications.

ii) If this Software is used in conjunction with

other non-Anritsu-approved software.

iii) Recovery of lost or damaged data.

iv) If this Software or the Equipment has been

modified, repaired, or otherwise altered

without Anritsu's prior approval.

v) For any other reasons out of Anritsu's direct

control and responsibility, such as but not

limited to, natural disasters, software virus

infections, etc.

b. Expenses incurred for transport, hotel, daily

allowance, etc., for on-site repairs by Anritsu

engineers necessitated by the above faults

shall be borne by you.

c. The warranty period for faults listed in

article 3a above covered by this EULA shall

be either 6 months from the date of purchase

of this Software or 30 days after the date of

repair, whichever is longer.

vii

4. Export Restrictions

You may not use or otherwise export or

re-export directly or indirectly this Software

except as authorized by Japanese and

United States law. In particular, this

software may not be exported or re-exported

(a) into any Japanese or US embargoed

countries or (b) to anyone on the Japanese or

US Treasury Department's list of Specially

Designated Nationals or the US Department

of Commerce Denied Persons List or Entity

List. By using this Software, you warrant

that you are not located in any such country

or on any such list. You also agree that you

will not use this Software for any purposes

prohibited by Japanese and US law,

including, without limitation, the

development, design and manufacture or

production of missiles or nuclear, chemical or

biological weapons of mass destruction.

5. Termination

Anritsu shall deem this EULA terminated if

you violate any conditions described herein.

This EULA shall also be terminated if the

conditions herein cannot be continued for

any good reason, such as violation of

copyrights, patents, or other laws and

ordinances.

6. Reparations

If Anritsu suffers any loss, financial or

otherwise, due to your violation of the terms

of this EULA, Anritsu shall have the right to

seek proportional damages from you.

7. Responsibility after Termination

Upon termination of this EULA in

accordance with item 5, you shall cease all

use of this Software immediately and shall

as directed by Anritsu either destroy or

return this Software and any backup copies,

full or partial, to Anritsu.

8. Dispute Resolution

If matters of dispute or items not covered by

this EULA arise, they shall be resolved by

negotiations in good faith between you and

Anritsu.

9. Court of Jurisdiction

This EULA shall be interpreted in

accordance with Japanese law and any

disputes that cannot be resolved by

negotiation described in Article 8 shall be

settled by the Japanese courts.

viii

Cautions against computer virus infection

•Copying files and data

Only files that have been provided directly from Anritsu or generated

using Anritsu equipment should be copied to the instrument.

All other required files should be transferred by means of USB or

CompactFlash media after undergoing a thorough virus check.

•Adding software

Do not download or install software that has not been specifically

recommended or licensed by Anritsu.

•Network connections

Ensure that the network has sufficient anti-virus security prote

ction in

place.

About This Manual



Composition of Operation Manuals

This operation manual is for MX269018A Analog Measurement Software

(Operation) are comprised as shown in the figure below.

Vector Signal Generator Operation Manual (Operation)

Vector Signal Generator Operation Manual (Remote Control)

MS2830A Signal Analyzer

Operation Manual

(Main Frame Operation)

MS2690A/MS2691A/MS2692A and MS2830A/MS2840A/MS2850A

Signal Analyzer Operation Manual (Main Frame Remote Control)

MS2840A Signal Analyzer

Operation Manual

(Main Frame Operation)

MX269018A Analog Measurement Software/

MS2830A/MS2840A Signal Analyzer Analog Signal Generator Operation Manual

(Operation)

MX269018A Analog Measurement Software

Operation Manual (Remote Control)

•Signal Analyzer Operation Manual (Mainframe Operation)

•Signal Analyzer Operation Manual (Mainframe Remote Control)

These describe basic operations, maintenance procedure, common

functions and common remote functions of the signal analyzer.

•Vector Signal Generator Operation Manual (Operation)

•Vector Signal Generator Operation Manual (Remote Control)

This describes the functions, operations, remote operations of Vector

Signal Generator option.

•MX269018A Analog Measurement Software/

MS2830A/MS2840A Signal Analyzer Analog Signal Generator Operation

Manual (Operation)

This manual describes how to operate the MX269018A Analog

Measurement Software and MS2830A, MS2840A signal analyzer

analog signal generator.

•MX269018A Analog Measurement Software Operation Manual (Remote

Control)

This manual describes how to use the MX269018A Analog

Measurement Software and MS2830A, MS2840A signal analyzer

analog signal generator via remote command.

As for MS2830A, MS2840A signal analyzer application's basic remote

control functions and its definitions of common commands, refer to

“MS2690A/MS2691A/MS2692A and MS2830A/MS2840A/MS2850A

Signal Analyzer Operation Manual (Mainframe Remote Control)”.



Document Conventions

This indicates the Signal Analyzer panel keys.

This indicates pages and sections to be referred to.

Boldface

This indicates message that appears on the screen.

‘’This indicates reference that does not pertain to screen

messages.

“ ” This indicates reference, or jump to other section of the

manual.

Convention Used in This Manual

Throughout this document, the use of MS2830A is assumed unless

otherwise specified. If using MS2840A, change MS2830A to read

MS2840A.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de Anritsu

Anritsu

Anritsu VNA Master MS2026C Manual de usuario

Anritsu

Anritsu Site Master S332D Manual de usuario

Anritsu

Anritsu MP2100A BERTWave Manual de usuario

Anritsu

Anritsu Site Master S120A Manual de usuario

Anritsu

Anritsu ShockLine Series Manual de usuario

Anritsu

Anritsu 3GPP Manual de usuario

Anritsu

Anritsu CMA 5000 - UTA Manual de usuario

Anritsu

Anritsu VectorStar ME7848A Series Manual de usuario

Anritsu

Anritsu MT8801C Manual de usuario

Anritsu

Anritsu Network Master Series Manual de usuario

Anritsu

Anritsu MT8802A Manual de usuario

Anritsu

Anritsu MS2687B Manual de usuario

Anritsu

Anritsu Spectrum Master MS2720T Manual del propietario

Anritsu

Anritsu MS2840A Manual de usuario

Anritsu

Anritsu MS2690A Manual de usuario

Anritsu

Anritsu Sire Master S331D Manual de usuario

Anritsu

Anritsu Spectrum Master MS2721B Manual de usuario

Anritsu

Anritsu VNA Master MS2024B Manual de usuario

Anritsu

Anritsu S331E Manual de usuario

Anritsu

Anritsu Network Data Analyzer MD6430A Manual de usuario

Anritsu

Anritsu MU196060A Manual de usuario

Anritsu

Anritsu MT9083B2 Manual de usuario

Anritsu

Anritsu MS2711B Manual de usuario

Anritsu

Anritsu CMA50 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario