AnkerWork BR300 USB Manual de usuario
For FAQs and more information, please visit:
support.ankerwork.com
@anker_official
@anker_JP
@Anke Official
@Anker_JP
@Anker Deutschland
@Anker Japan
@Anker
AnkerWork BR300 USB
Video Conference Bar
USER MANUAL
A3387 51005003360 V1
01 EN
English 01
简体中文 17
What's Included
1 2
75 6
×6
3
4
1
AnkerWork BR300 USB Video Conference Bar
2
Remote control
3
Power adapter
4
Power plug*
5
2 m USB cable (USB-C to USB-A)
6
Wall mount bracket
7
Screws and anchors
* Power plug may vary in different regions.
EN 02 03 EN
At a Glance
Front View
1
3
2 4
1
Camera
2
Speaker
3
LED lights
4
Microphone
Rear View
5
2 3 4
86 7
1
1
DC-IN port
2
USB-C port
• Connect to power supply.• Connect to a computer.
3
HDMI port
4
USB-A port
• Connect to a monitor to stream video from the video bar. • Connect to an external microphone.
5
Security slot
6
USB mounting hole
• 7 × 3 mm • Secure the USB connector.
7
Reset key
8
Adjustable base
EN 04 05 EN
Remote Control
1Turn the camera on / off.
2
• Answer or make a call.
• Enter the call interface.
3
Move the camera up, down, le, or right.
4Volume up / down.
5Exit tracking mode.
6Enter speaker tracking mode when no external
microphone is connected.
7
• Press to apply a camera preset.
• Press and hold for 3s to save a camera preset.
8
• Press to apply a second camera preset.
• Press and hold for 3s to save a second camera preset.
9
• Press to switch to active status.
• Press and hold for 3s to switch to standby status.
10 Reject a call.
11
• Confirm a selection.
• Return the camera to center.
12 Mute / unmute the microphone.
13 Zoom in / out.
14 Turn the speaker on / off.
15 Enter participant tracking mode.
16 Access / exit the menu page.
17 Enable / disable Bluetooth pairing.
EN 06 07 EN
Getting Started
Setting Up Your Video Bar
Option A: On Your Desk
Adjust the video bar up or down to your preferred position.
165° 15°
Option B: On the Wall
1. Install the wall mount bracket onto the wall by using the screws and anchors included.
2. Attach the video bar to the wall mount bracket.
1 2
Option C: Above or Below Your Monitor
• An optional TV mount bracket* can position the video bar above or below your monitor.
• The bracket can attach to the VESA-standard mounting holes available on most monitors.
1. Adjust the bracket so that it can support the monitor while aligning with the mounting holes.
2. Fasten the bracket to the monitor using the screws from the back of the monitor.
3. Attach the video bar to the bracket.
*AnkerWork BR300 TV Mount is available for purchase.
EN 08 09 EN
Preparing the Remote
1. Press to open the battery cover.
2. Insert two new AAA batteries (not included) matching the polarity (+/-) indicated, and close the battery cover.
1 2
Pairing the Remote with Video Bar
• Your remote is already paired with the video bar and ready for use when powered on.
• You may need to manually pair a remote with the video bar when replacing a lost remote or experiencing any control
problems.
1. Turn on the video bar and make sure that you can see an image output.
2. Press and hold and until the LED on the remote turns solid red. This indicates that the pairing history has been cleared.
3. Insert a paper clip (not included) into the reset key and push gently. The LEDs on the video bar will light up blue in a
sequence during the pairing process.
4. Press and hold until the LEDs on the video bar flash blue. This indicates that pairing is completed.
EN 10 11 EN
Connecting
Option A: Connecting to Computer (USB Cable)
1. Plug the provided power adapter and power plug into the video bar.
- The LEDs on the video bar will turn white.
2. Connect your computer to the USB-C port on the video bar using the provided USB cable. Your video bar will be ready to use
when connected.
3. Connect the computer to one or more monitors depending on the computer's capability.
4. Optional: To stream video from the video bar, connect it to a monitor using an HDMI cable (not included).
5. Optional: To extend the voice pickup range in a medium-sized meeting room, connect an external microphone* to the USB-A
port on the video bar using the USB cable (not included).
1
2
3
4
5
• The video bar will automatically turn on once connected to a power supply.
• Your computer and video bar cannot be connected to the same monitor simultaneously.
• Make sure to select "AnkerWork BR300 USB Video Conference Bar" as the audio and video device in your conferencing
software.
*AnkerWork BR300 USB External Mic is available for purchase.
Option B: Connecting to Smartphone (Bluetooth)
The video bar only supports audio calls when connected to a smartphone via Bluetooth pairing.
1. Press on the remote to enter Bluetooth pairing mode.
- The LEDs on the video bar will flash blue.
2. Select "AnkerWork BR300 USB Video Conference Bar" on your device's Bluetooth list to connect.
- When successfully connected, the LEDs on the video bar will turn solid blue.
1 2
AnkerWork BR300 USB
Video Conference Bar
Pairing Connected
EN 12 13 EN
• To disconnect Bluetooth, press again.
Using Camera Presets
The remote includes buttons that can be used to set two default camera positions.
Saving Camera Presets
1. Make sure to exit tracking mode by pressing .
2. Use to adjust the camera to the position you want.
3. Press and hold the 1or 2button for 3s to save the preset.
- Old presets will be overwritten.
15°
Applying Camera Presets
1. Make sure to exit tracking mode by pressing .
2. Press the 1or 2button to apply a preset.
LED Light Guide
Solid white Camera in use
Solid purple Camera not in use
Solid red Microphone muted
Lighting up blue in a sequence Pairing with remote
Flashing blue Paired with remote
Flashing blue Pairing with Bluetooth device
Solid blue Paired with Bluetooth device
Flashing amber Updating firmware
EN 14 15 EN
AnkerWork Software
Download the AnkerWork Software from
software.ankerwork.com
Download and install the AnkerWork soware on your computer to update firmware.
Specifications
Specifications are subject to change without notice.
Input 12V 2A
USB Port 1 x USB 3.0, USB-C
1 x USB 2.0, USB-A
HDMI Port 1 x HDMI, Version 1.4b
Resolution 4K@30fps, 1080P@30fps, 720P@30fps
Voice Algorithm Beamforming, AGC (Auto Gain Control), AEC (Acoustic Echo Cancellation), ANC (Auto Noise
Cancellation)
Field of View (FOV) 121°
Sensor 8.51 MP CMOS (1 / 2.5 in.)
Video Codec H.264, MJPEG, YUV2, NV12
Speaker 96db SPL @ 0.5m
Voice Pickup Distance 6 m
Bluetooth Version 5.0
17 SCEN 16
Customer Service
18-month limited warranty
Lifetime technical support
Our warranty is additional to the legal rights consumers have buying this product.
+1 (800) 988 7973 (US) Mon-Fri 6:15AM-5:00PM (PST)
Anker Innovations Limited
Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong
包装内容
1 2
75 6
×6
3
4
1
AnkerWork BR300 USB 视频会议一体机
2
遥控器
3
电源适配器
4
电源插头 *
5
2 米 USB 电缆（USB-C 转 USB-A）
6
壁挂式支架
7
螺钉和锚栓
* 电源插头可能因地区而异。
Tabla de contenidos
Manuales populares de Sistema de conferencias de otras marcas
Kramer
Kramer VIA GO Manual de usuario
AVT
AVT MAGIC AC1 Go Manual de usuario
ProSoft Technology
ProSoft Technology AN-X4-AB-DHRIO Manual de usuario
Sony
Sony PCS-I150 Manual de usuario
Middle Atlantic Products
Middle Atlantic Products VTC Series Manual de usuario
Prentke Romich Company
Prentke Romich Company Vanguard Plus Guía
