Anatomic SITT Zitzi Pengy Manual de usuario

User manual
Zitzi Pengy Pro Seat
EN
2020-01-08

2User manual – Pengy Pro Seat 2www.anatomicsitt.com | +46 11 16 18 00
Table of contents
Safety precautions ��������������������������������� 3
Introduction �������������������������������������������������������������������������3
Field of application�����������������������������������������������������������3
Correspondence ����������������������������������������������������������������3
Crash tested�������������������������������������������������������������������������3
Headrest����������������������������������������������������4
Mounting the headrest �������������������������������������������������� 4
Height adjusting ��������������������������������������������������������������� 4
Angle adjusting����������������������������������������������������������������� 4
Adjusting the headrest plate sideways ���������������� 4
Backrest ���������������������������������������������������� 5
Adjustment of backrest height�����������������������������������5
Adjustment of the lateral support ���������������������������5
Adjusting the backrest angle ��������������������������������������5
Seat part ���������������������������������������������������6
Seat depth and leg length dierence �������������������� 6
Abduction, adduction and windswept������������������ 6
Adjusting the seat pocket�������������������������������������������� 6
Hip belt������������������������������������������������������ 7
Adjusting the hip belt �����������������������������������������������������7
Armrest ����������������������������������������������������� 8
Width adjustment �������������������������������������������������������������8
Height / angle up-down adjustment�����������������������8
Rotating the armrest plate �������������������������������������������8
Table, solid������������������������������������������������9
Mounting the table���������������������������������������������������������� 9
Crossbar�������������������������������������������������� 10
Installation of crossbar �������������������������������������������������10
Hip support ��������������������������������������������� 11
Mounting of hip support����������������������������������������������� 11
Sun cover ������������������������������������������������� 11
Mounting of suett �������������������������������������������������������� 11
Chest harness������������������������������������������12
Mounting of upper support bracket���������������������� 12
Mounting on Pengy sulky ��������������������13
Mounting on Pengy sulky�������������������������������������������� 13
Unmounting from Pengy sulky��������������������������������� 13
Advanced footrest������������������������������� 14
Mounting and adjusting����������������������������������������������� 14
Calf support advanced footrest����������15
Ankleholder��������������������������������������������� 15
Foot strap������������������������������������������������ 16
Maintenance instructions���������������������17
Service intervals��������������������������������������������������������������� 17
Cleaning and washing instructions ������������������������ 17
Tools��������������������������������������������������������������������������������������� 17
Warranty������������������������������������������������������������������������������ 17
Spare parts������������������������������������������������������������������������� 17
Reconditioning ����������������������������������������������������������������� 17
Marking �������������������������������������������������������������������������������� 17
Recycling����������������������������������������������������������������������������� 17
Summary and follow-ups ���������������������18
Follow-up inspections��������������������������������������������������� 18
Adaptation and customization�����������18
Guidelines and recommendations ��������������������������18
Terms of sale������������������������������������������ 19
Warranty ����������������������������������������������������������������������������19
Warranty claims���������������������������������������������������������������19
Returning products��������������������������������������������������������19

3www.anatomicsitt.com | +46 11 16 18 00User manual – Pengy Pro Seat
Introduction
For you to use all advandtages of the Zitzi Pengy Pro, it is important that you read
this manual thoroughly� This applies to all persons who are in the vicinity of the
user� The product is designed for users with seating problems and fits many dier-
ent types of diagnoses� Adjustment of Pengy Pro should always be performed by
medically qualified person�
If you need additional information, please contact Anatomic SITT AB�
Field of application
The product is intended for use as a seating system together with the chassis
produced by Anatomic SITT AB� If the desire for another use can be found, please
contact Anatomic SITT AB�
Correspondence
Zitzi Pengy and its accessories are CE marked products� A unique serial number is
located on a label placed on the back or under the seat� This serial number should
be quoted in any correspondence regarding the product�
Crash tested
The Pengy seating system is crashtested and approved together with the Pengy
sulky according to ISO 7176-19
Check the checkbox if the product
is CUSTOMIZED�
The CE Mark is no longer valid and
should be removed�
Place of label
This product is manufactured by Anatomic SITT AB
Postal address Anatomic SITT AB, Box 6137, SE-600 06 Norrköping
Street address Anatomic SITT AB, Terminalgatan 1, SE-603 61 Norrköping
Phone +46 11-161800
Fax +46 11-162005
Email info@anatomicsitt�com
Webb anatomicsitt�com
Instructions movies youtube�com/anatomicsitt
Follow us on facebook�com/anatomicsitt
Safety precautions

4User manual – Pengy Pro Seat 4www.anatomicsitt.com | +46 11 16 18 00
Mounting the headrest
Mount the main support bracket with lever handle (B) and its washer and screw
(A)� Note that the screw (A) should not be to tightened, it shoulde be possible to
move up and down when the lever knob (B) is loosened�
Height adjusting the headrest
To adjust the height of the headrest, loosen the lever handle (B) and move the
headrest to desired position� Then tighten lever handle (B)�
Angle adjusting the headrest
When adjusting the 3-joint headrest, loosen the screw (C) in the joint you
wish to adjust� Once you reach the desired position, tighten the screw (C) again�
Adjusting the headrest plate sideways
Loosen the screws (D)� Adjust the headrest plate to desired position and tighten
the screws (D) again�
Headrest
Lever handle (B)
Screw (A)
E
(C)
(D)

5www.anatomicsitt.com | +46 11 16 18 00User manual – Pengy Pro Seat
Backrest
Lateral
support (B) Lateral
support (B)
Back and hip angle (C)
Back and hip
angle (D)
Back height (A)
160°
Adjustment of backrest height
To adjust the back height, loosen the screws (A) using the adjustment
key and then adjust it to desired height� When you are satisfied with the
setting tighten the screws (A) again�
Adjustment of lateral support
To width and height adjust the lateral supports, loosen the knobs (B) and then
adjust to the desired height and width� Tighten the knobs (B) when you reach the
desired position�
Adjusting the back angle
To adjust the angle of the back first loosen lever (C), press the button (D) and ad-
just to the desired angle / position, tighten lever (C)�

6User manual – Pengy Pro Seat 6www.anatomicsitt.com | +46 11 16 18 00
Adjust seat depth and Leg length dierence
Loosen the screw (A) on the leg part with the help of the adjustment key, and then
adjust the leg part to the desired length� Then tighten the screw (A) again�
Abduction, adduction and windswept
To adjust the leg part to any of these positions, loosen the screw (A) using allen
key, and move the leg part to desired postion� Tighten the screw (A)�
Adjusting the seat pocket
When adjusting the seat depth, the seat pocket should also be adjusted�
Loosen the leg parts screws (B) with the allen key� Use the color code of the seat
depth and adjust the seat pocket to the desired position� Tighten the screws (B)�
Seat part
Size label/Colour code
Seat pocket plate
A
B
Note! You don’t have to remove the screws completely to adjust, just
loosen them slightly�
Tip! To get a good starting point for setting the seat depth, the color
scale on the seatbase and depth adjustment plate can be used as a
guide� For example if the seat depth is adjusted to blue field the depth
adjustment plate should also be set to the blue field� This ensure a
correct seat pocket size according to the seating position� Always fine-
tune the settings after each users requirements�
100 mm
11 mm 15 mm
40 mm
8 mm
10 mm
STORLEK 1 SKALA 1:1
PENGY
DETTA SKA VARA PÅ EGET ARK
21
22
23
24
25
26
27
28
20
19
21
22
23
24
25
26
27
28
20
19

7www.anatomicsitt.com | +46 11 16 18 00User manual – Pengy Pro Seat
Adjusting the hip belt
When mounting the hip belt in the hip belt tracks, use a tri-glide buckle�
For assembly according to the tri-glide method, see picture�
Hip belt
Hip belt tracks
Standard
positionons
of hip belt

8User manual – Pengy Pro Seat 8www.anatomicsitt.com | +46 11 16 18 00
Width adjustment
To change the width of the armrest, loosen the screw (B) and then move the
armrest to the desired positon, then tighten the screw (B)�
For more with adjustment remove the screw (A) and turn the angle bracket 180°,
then tigthen the screws (A)�
Height adjustment / Angle adjustment up/down
To adjust the height of the armrest, loosen the lever handle (A) and move
the armrest to the desired height and angle, then tighten lever handle (A)�
Lateral adjustment angle
To adjust the height of the armrest, loosen the screws (B) and rotate
the armrest to the desired position, then tighten the screws (B)�
Armrest
A
B

9www.anatomicsitt.com | +46 11 16 18 00User manual – Pengy Pro Seat
Locking lever
Mounting the table
Put the table on the armrest plates and then rotate the locking lever of the
table into position below the armrest plate� The locking lever must be rotated
until it is inside the rim of the raised armrest plate�
Table, solid

10User manual – Pengy Pro Seat 10 www.anatomicsitt.com | +46 11 16 18 00
Installation of crossbar
The bracket for the crossbar (A) is mounted under the armrest plates with the
supported screws and fittings with grooves (C)� The bow is pushed in and tightened
with knob (B) on both sides�
The crossbar can be pulled out on the left side and rotaded away while the right
side is still remains in the fitting pipe�
Crossbar
A
B
C
Loosen the knobs in the mounting bracket under the armrest plates�
Insert the bow and lock the knobs�
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Ayuda a la movilidad de Anatomic SITT
Manuales populares de Ayuda a la movilidad de otras marcas

Rhythm Healthcare
Rhythm Healthcare B3800F Manual de usuario

AMF-BRUNS
AMF-BRUNS PROTEKTOR Manual de usuario

Drive DeVilbiss Healthcare
Drive DeVilbiss Healthcare OTTER Manual de usuario

Rhythm Healthcare
Rhythm Healthcare C500U Manual de usuario

Lumex
Lumex RJ4200A Manual de usuario

Rebotec
Rebotec Jumbo Manual de usuario














