Analytic Systems BCH10W Manual de usuario

INSTALLATION &

OPERATION MANUAL

BCH10W & BCH10Y BATTERY CHARGER

IMPORTANT & SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS — This manual contains important safety and operating

instructions for the battery charger.

BATTERY CHARGER PRECAUTIONS

1. Do not expose the battery charger to rain or snow unless it is a sealed model.

2. Use of an attachment not recommended or sold by the battery charger manufacturer may

result in a risk of re, electric shock, or injury to persons.

3. Do not disassemble the battery charger; return it to the manufacturer or an authorized

service center when service or repair is required. Incorrect reassembly may result in a

risk of electric shock or re. Voltages in excess of 350 volts are present inside the charger

anytime it is plugged into an AC outlet, even if it is switched off.

4. To reduce risk of electric shock, unplug the battery charger from the AC outlet before

attempting any maintenance or cleaning. Turning off controls will not reduce this risk.

5. Never place battery charger directly above battery; gases from battery will corrode and

damage battery charger.

6. Never allow battery acid to drip on the battery charger.

BATTERY SAFETY

1. WARNING — RISK OF EXPLOSIVE GASES

i. WORKING IN VICINITY OF A LEAD-ACID BATTERY IS DANGEROUS. BATTERIES

GENERATE EXPLOSIVE GASES DURING NORMAL BATTERY OPERATION. FOR THIS

REASON, IT IS OF UTMOST IMPORTANCE THAT EACH TIME BEFORE SERVICING

EQUIPMENT IN THE VICINITY OF THE BATTERY, YOU READ THIS USER GUIDE AND

FOLLOW THE INSTRUCTIONS EXACTLY.

ii. To reduce risk of battery explosion, follow these instructions and those published by

the battery manufacturer and manufacturer of any equipment you intend to use in

vicinity of battery. Review the cautionary marking on these products.

2. PERSONAL PRECAUTIONS

i. Someone should be within range of your voice or close enough to come to your aid

when you work near a battery.

ii. Have plenty of fresh water and soap nearby in case battery acid contacts skin,

clothing, or eyes.

iii. Wear complete eye protection and clothing protection. Avoid touching eyes while

working near battery.

iv. If battery acid contacts skin or clothing, wash immediately with soap and water. If acid

enters eye, immediately ood eye with running cold water for at least 10

v. minutes and get medical attention immediately.

vi. NEVER smoke or allow a spark or ame in the vicinity of a battery.

vii. Be extra cautious to reduce risk of dropping a metal tool onto battery. It might spark

or short-circuit the battery or other electrical part that may cause a re or explosion.

viii. Remove personal metal items such as rings, bracelets, necklaces, and watches when

working with a lead-acid battery. A lead-acid battery can produce a short- circuit

current high enough to melt metal, causing a severe burn.

ix. NEVER charge a frozen battery.

x. If it is necessary to remove a battery from service, always remove grounded terminal

from battery rst. Make sure all accessories connected to the battery are off, to

prevent an arc when reconnecting the new battery.

xi. Be sure area around battery is well ventilated.

xii. Clean the battery terminals. Be careful to keep corrosion from coming in contact with

eyes.

xiii. Study all the battery manufacturer’s specic precautions such as removing or not

removing cell caps while charging and recommended rates of charge.

Medical Equipment Notice

Analytic Systems does not recommend the use of their products in life support

pplications where failure or malfunction of this product can be reasonably

expected to cause failure of the life support device or to signicantly affect its

safety or effectiveness. Analytic Systems does not recommend the use of any of

its products in direct patient care. Examples of devices considered to be life

support devices are neonatal oxygen analyzers, nerve stimulators (whether used

for anesthesia, pain relief, or other purposes), auto-transfusion devices, blood

pumps, debrillators, arrhythmia detectors and alarms, pacemakers,

hemodialysis systems, peritoneal dialysis systems, neonatal ventilator

incubators, ventilators for both adults and infants, anesthesia ventilators, and

infusion pumps as well as any other devices designated as “critical” by the U.S.

FDA.

TABLE OF CONTENTS

• Front Cover, Product Photo and Title

• Product warnings and advisories

• Table of Contents

• Description/Overview of product

• Main Parts

• Operation instructions

• Mounting Instructions

• Connection instructions

• Options

• Faults

• Specications

• Warranty

Revised - September 29, 2016

Introduction

The BCH10W Step Down series of Battery Chargers supply up to 10 amps of charging current

at 12, 24, 36 or 48 volts from any higher voltage between 20 and 80 volts DC in an IP66 rated

watertight and EMC shielded enclosure for use in automotive, heavy equipment, marine,

industrial, rail or alternative energy environments. The output voltage is congured to allow

permanent connection to the battery.

The standard BCH10W model offers a Deutsch connector on a pigtail input/output cable and is

designed to be water resistant to IP66.

The BCH10Y is an upgraded version with the same connections that is individually tested to

meet IP67.

The all surface mount high frequency design offers higher reliability, higher efciency (more

than 91%), more power (up to 544 watts at 48 VDC Out) and minimum size. Two LED indicators

show the presence of input power, and when the unit is charging (output current is greater

that 2 amps).

The unit has reverse input protection, reverse battery connection protection, output

overvoltage protection and features spark free connection to the battery. Smart Ideal Diode

output circuitry prevents any reverse current owing from the battery back into the converter.

Main Parts

Front Panel

1. Deutsch DT04-4P Input/Output

connector on pigtail

2. Input Power Good LED

3. Charging LED

Operation

To turn the unit on, simply turn on your source of power. The Input Power LED will illuminate

to indicate the presence of input power.

The BCH10 will immediately begin charging the battery. When the unit is rst turned on,

it will charge the batteries at a constant current and the charging light will be on. After a

period of time, which may be minutes to hours, the batteries will reach the oat voltage and

the charging current will begin to drop. When the current falls to 10% of the rated charging

current, the charging light will go off, and the charger will maintain the batteries at the oat

voltage. You may check this voltage at the battery with a good digital voltmeter. As shipped

from the factory, the unit is preset to the oat voltage listed in the specications, which is

generally recommended for lead-acid batteries.

Mounting

Mount the unit and allow at least 1 inch

of clearance for adequate cooling.

Input and Output Connections

This unit is equipped with a watertight gland

and short 4 conductor pigtail terminated with

a Deutsch DT04-4P connector. The mating

connector is also supplied, but without

cable. The plug pin out is shown in the table

below.

PIN NAME DESCRIPTION

1 POSITIVE INPUT (red)

2 NEGATIVE INPUT (black)

3 NEGATIVE OUTPUT (black)

4 POSITIVE OUTPUT (orange)

Connect the input pins to the power source, and the output pins to the load, making sure

to observe the correct polarity of the connections. If the input is connected in reverse, the

protection fuse will blow, and must be replaced by the dealer or an electronics technician.

4.64

0.21

5.91

2.15

7.0±1.0

orange

black

1 red

2 black

Installation

ROHS (European) Option (E Option)

IP67 (Waterproof Tested) Option (Y Option)

Troubleshooting

Consistent with military standards, this unit is normally manufactured using lead based solder.

However, this unit can be built to ROHS lead free standards, identied internally by a red

colored printed circuit board by adding the E option. This is a no charge option, but can add 2-4

weeks to the delivery of an order.

This is the same unit as the VHC10W, except each unit is individually tested to comply with

the IP67 rating of withstanding 1 meter immersion for 30 minutes with no ingress of moisture.

This unit provides LED indicators to help diagnose any problems.

CHARGING Indicates that the battery charger is charging the batteries:

If the LED is not on, the batteries may be fully charged and the charger is

supplying a oat voltage to the batteries to keep them fully charged.

INPUT POWER Indicates that power is being received by the unit

If the LED is not on, check with a voltmeter that there is power at the

connections.

Check that the polarity is correct, Positive to Pin 1 and Negative to Pin 2.

If the power is reversed, the unit is not damaged, but the input fuse

must be replaced by a service technician experienced in Surface Mount

Technology.

Specications

Input Voltages

MODEL BCH10W(Y)-12 BCH10W(Y)-24 BCH10W(Y)-32 BCH10W(Y)-36 BBCH10W(Y)-48

Input Volts 20 - 80 VDC 30 - 80 VDC 40 - 80 VDC 45 - 80 VDC 60 - 80 VDC

Electrical

Input Ripple and Noise <100 mV Peak to Peak

Output Ripple and Noise < 50 mV Peak to Peak

Transient Response <300 mV for 50% Load Step Change

Regulation (Line & Load) < +/- 0.5%

Emissions Meets MIL-STD-461F

Mechanical

Dimensions 6.20 in / 15.8 cm Long x 4.91 in / 12.5 cm Wide x 2.15 in / 5.5 cm High

Clearance 1.0 in / 2.5 cm all around

Weight 0.62.0 lb / 0.28 kg

Material and Finish Diecast Aluminum with O-Ring and EMC Gaskets, Black Powder Coat Finish

Mounting Wall or shelf mount

Connections BCHW - Deutsch DT04-4P on 15cm Pigtail; Mating Connector Included

Shock and Vibration Designed to meet MIL-STD-810G

Environmental and Safety

Operating Temperature Range -40°C to +55°C @ maximum output

Humidity 0 - 95% Relative Humidity (non-condensing) with standard conformal coating

Ingress Protection W versions - Built to meet IP66, Y versions - tested to meet IP67

Audible Noise NONE 0db @ 3ft

Typical Service Life > 10 years (87,600 hrs)

Isolation Any input or output to case (1500 VDC)

Input to output - common negative

Warranty Two years parts and labor

Safety Built to meet CSA 22.2.107.1 & UL458

Output Voltages

Output Volts Nominal 12 VDC 24 VDC 32 VDC 36 VDC 48 VDC

Actual Volts 13.6 VDC 27.2 VDC 36.3 VDC 40.8 VDC 54.4 VDC

Output Amps 10 Amps Continuous

Dissipation 12 Watts

Efciency 91.9% 95.8% 96.8% 97.1% 97.8%

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cargador de baterías de Analytic Systems

Analytic Systems

Analytic Systems BCD180 Series Manual de usuario

Analytic Systems

Analytic Systems 99381 Manual de usuario

Analytic Systems

Analytic Systems BCD300 series Manual de usuario

Analytic Systems

Analytic Systems BCA1505U-24DW Manual de usuario

Analytic Systems

Analytic Systems BCD180 Series Manual de usuario

Analytic Systems

Analytic Systems BCA1505 SERIES Manual de usuario

Analytic Systems

Analytic Systems BCA-PWS-480-36 Manual de usuario

Analytic Systems

Analytic Systems BCD610 Manual de usuario

Analytic Systems

Analytic Systems IBC320 Manual de usuario

Analytic Systems

Analytic Systems BCA1000 Manual de usuario

Analytic Systems

Analytic Systems BCD1000-110-12 Manual de usuario

Analytic Systems

Analytic Systems BCD615 SERIES Manual de usuario

Analytic Systems

Analytic Systems BCD310 Series Manual de usuario

Analytic Systems

Analytic Systems BCD315 Series Manual de usuario

Analytic Systems

Analytic Systems BCD615R Manual de usuario

Analytic Systems

Analytic Systems BCD600 Series Manual de usuario

Analytic Systems

Analytic Systems IBC320 Manual de usuario

Analytic Systems

Analytic Systems BCA1510MS-24 Manual de usuario

Analytic Systems

Analytic Systems BCD315MW Manual de usuario

Analytic Systems

Analytic Systems BCA310 Series Manual de usuario

Analytic Systems

Analytic Systems BCD805W-24-24 Manual de usuario

Analytic Systems

Analytic Systems BCD305-12-24 Manual de usuario

Analytic Systems

Analytic Systems BCD305 Series Manual de usuario

Analytic Systems

Analytic Systems BCA310-110-48 Manual de usuario

Manuales populares de Cargador de baterías de otras marcas

AA Portable Power Corp

AA Portable Power Corp Universal Smart Charger Manual de usuario

Enelion

Enelion Vertica Manual de usuario

RCA

RCA CHU6 Manual de usuario

ANSMANN

ANSMANN ALCT 6/24-10 Manual de usuario

Hitachi

Hitachi UC 18YRSL Guía de solución de problemas

Olympus

Olympus B-20 LPC Manual de usuario

Exibel

Exibel ZH1708143 Manual de usuario

Lenmar

Lenmar Mach 1 Manual de usuario

CTEK

CTEK MXS 5.0 Manual de usuario

ABB

ABB HT842379 Manual de usuario

Nitecore

Nitecore Superb Charger SC4 Manual de usuario

Renogy

Renogy RBC2125DS-21W Manual de usuario

Braun

Braun BWC02M Manual de usuario

CTEK

CTEK MXS 3.6 Manual de usuario

Black & Decker

Black & Decker BDV090 Manual de usuario

Trinity

Trinity DPD Manual de usuario

Hulkman

Hulkman Sigma 1 Manual de usuario

IKEA

IKEA koppla Manual de usuario