Analog Devices ADSP-CM403F EZ-KIT Lite Manual de usuario

ADSP-CM403F EZ-KIT Lite®

Evaluation System Manual

Revision 1.0, September 2013

Part Number

82-000342-01

Analog Devices, Inc.

One Technology Way

Norwood, Mass. 02062-9106

may not be reproduced in any form without prior, express written consent

from Analog Devices, Inc.

Printed in the USA.

Disclaimer

Analog Devices, Inc. reserves the right to change this product without

prior notice. Information furnished by Analog Devices is believed to be

accurate and reliable. However, no responsibility is assumed by Analog

Devices for its use; nor for any infringement of patents or other rights of

third parties which may result from its use. No license is granted by impli-

cation or otherwise under the patent rights of Analog Devices, Inc.

Trademark and Service Mark Notice

The Analog Devices logo, EngineerZone, EZ-Board, and EZ-KIT Lite are

registered trademarks of Analog Devices, Inc.

All other brand and product names are trademarks or service marks of

their respective owners.

Regulatory Compliance

The ADSP-CM403F EZ-KIT Lite is designed to be used solely in a labo-

ratory environment. The board is not intended for use as a consumer end

product or as a portion of a consumer end product. The board is an open

system design which does not include a shielded enclosure and therefore

may cause interference to other electrical devices in close proximity. This

board should not be used in or near any medical equipment or RF devices.

The ADSP-CM403F EZ-KIT Lite is in the process of being certified to

comply with the essential requirements of the European EMC directive

2004/108/EC and therefore carries the “CE” mark.

The EZ-KIT Lite evaluation system contains ESD (electrostatic discharge)

sensitive devices. Electrostatic charges readily accumulate on the human

body and equipment and can discharge without detection. Permanent dam-

age may occur on devices subjected to high-energy discharges. Proper ESD

precautions are recommended to avoid performance degradation or loss of

functionality. Store unused EZ-KIT Lite boards in the protective shipping

package.

ADSP-CM403F EZ-KIT Lite Evaluation System Manual v

CONTENTS

PREFACE

Product Overview ............................................................................ x

Purpose of This Manual ................................................................ xiii

Intended Audience ......................................................................... xiv

Manual Contents ............................................................................ xv

What’s New in This Manual ............................................................ xv

Technical Support .......................................................................... xvi

Supported Processors ...................................................................... xvi

Supported Tools ............................................................................ xvii

Product Information ..................................................................... xvii

Analog Devices Web Site ......................................................... xvii

EngineerZone ......................................................................... xviii

Notation Conventions .................................................................. xviii

Contents

vi ADSP-CM403F EZ-KIT Lite Evaluation System Manual

USING ADSP-CM403F EZ-KIT LITE

Package Contents ......................................................................... 1-2

ADSP-CM403F EZ-Board ............................................................ 1-3

Default Configuration .................................................................. 1-3

IAR Embedded WorkBench and Board Installation ....................... 1-5

IAR Embedded WorkBench Session Startup .................................. 1-6

SPI Flash ...................................................................................... 1-8

Analog Interface ........................................................................... 1-8

UART0 Interface (RS-232) ........................................................... 1-9

CAN0 Interface .......................................................................... 1-10

Debug Interface .......................................................................... 1-10

Serial Liquid Crystal Display Module Interface ............................ 1-10

Power-On-Self Test ..................................................................... 1-11

Expansion Interface .................................................................... 1-11

Power Architecture ..................................................................... 1-12

Power Measurements .................................................................. 1-12

Example Programs ...................................................................... 1-13

Reference Design Information ..................................................... 1-13

ADSP-CM403F EZ-KIT Lite Evaluation System Manual vii

Contents

ADSP-CM403F EZ-KIT LITE HARDWARE REFERENCE

System Architecture ...................................................................... 2-2

Software-Controlled Switches (SoftConfig) .................................... 2-3

Overview of SoftConfig ........................................................... 2-3

SoftConfig on the ADSP-CM403F EZ-KIT LITE ................... 2-7

Programming SoftConfig Switches ........................................... 2-8

Push Buttons and Switches .......................................................... 2-12

Boot Mode Select Switch (SW1) ............................................ 2-13

Reset Push Button (SW2) ...................................................... 2-13

GPIO Push Buttons (SW3-4) ................................................ 2-13

Jumpers ...................................................................................... 2-14

VREF0 External Source Jumper (JP1) .................................... 2-15

VREF1 External Source Jumper (JP2) .................................... 2-15

Buffer Input Select Jumper (JP3) ........................................... 2-15

Power Select Jumper (JP4) ..................................................... 2-16

Power Jumpers (P4–6) ........................................................... 2-16

LEDs .......................................................................................... 2-17

GPIO LEDs (LED1–3) ......................................................... 2-18

Reset LED (LED4) ................................................................ 2-18

Power LED (LED5) ............................................................... 2-18

SYS_FAULT LED (LED6) ..................................................... 2-18

Contents

viii ADSP-CM403F EZ-KIT Lite Evaluation System Manual

Connectors ................................................................................. 2-19

DCE UART Connector (J1) .................................................. 2-20

Asynch or Memory Connector (J2) ........................................ 2-20

Character Display Connector (J3) ......................................... 2-20

PWM Connector (J7) ........................................................... 2-21

CAN0 Connector (J8) ........................................................... 2-21

Analog Connector (J9) .......................................................... 2-21

JTAG/SWD/SWV Connector (P1) ........................................ 2-21

TRACE and JTAG/SWD/SWV Connector (P2) .................... 2-22

VREF Buffered Connector (P3) ............................................. 2-22

Power Connector (P7) ........................................................... 2-22

ADSP-CM403F EZ-KIT LITE BILL OF MATERIALS

ADSP-CM403F EZ-KIT LITE SCHEMATIC

INDEX

ADSP-CM403F EZ-KIT Lite Evaluation System Manual ix

PREFACE

Thank you for purchasing the ADSP-CM403F EZ-KIT Lite®, Analog

Devices, Inc. low-cost evaluation system for the ADSP-CM403F

mixed-signal control processor.

The ADSP-CM403F processor is based on the ARM®Cortex®-M4 pro-

cessor core and is designed for photovoltaic applications. The EZ-KIT

Lite is shipped with all of the necessary hardware—you can start the eval-

uation immediately. The package contains the standalone evaluation

board and CE-approved power supply. The EZ-KIT Lite version ships

with the J-Link Lite ARM, while the EZ-Board®version requires the cus-

tomer to provide a debugger.

Two expansion connectors (analog interface and PWM/digital interface)

are provided for connecting boards that incorporate motors. Another

expansion connector is provided for connecting an Anybus board and/or a

memory/FPGA extender card.

Traditional mechanical switches for changing the board’s factory setup

have been removed in favor of I2C controlled software switches. The only

remaining mechanical switches are the boot mode switch and push

buttons.

Product Overview

x ADSP-CM403F EZ-KIT Lite Evaluation System Manual

The evaluation board is designed to be used in conjunction with the IAR

Embedded Workbench development tools to test capabilities of the

ADSP-CM403F processors. The development environment aids advanced

application code development and debug, such as:

• Create, compile, assemble, and link application programs written

in C++, C, and assembly

• Load, run, step, halt, and set breakpoints in application programs

• Read and write data and program memory

• Read and write core and peripheral registers

Product Overview

The board features:

• Analog Devices ADSP-CM403F processor

• 120-pin LQFP package

• 30 MHz CLKIN core oscillator

• Universal Asynchronous Receiver/Transmitter (UART0)

• Analog Devices ADM3252E RS-232 line transceiver

• DB9 female connector

• Controller Area Network (CAN) interface

• Analog Devices ADM3053 transceiver

• RJ11 connector

Tabla de contenidos

Otros manuales de Placa madre de Analog Devices

Analog Devices

Analog Devices EZ-KIT Lite Manual de usuario

Analog Devices

Analog Devices ADP5360 Manual de usuario

Analog Devices

Analog Devices LINEAR TECHNOLOGY LTC2874 Guía de configuración rápida

Analog Devices

Analog Devices EVAL-ADAQ4003FMCZ Manual de usuario

Analog Devices

Analog Devices EVAL-AD5680DBZ Manual de usuario

Analog Devices

Analog Devices EV-AD74412RSDZ Manual de usuario

Analog Devices

Analog Devices EVAL-ADPDM3Z Manual de usuario

Analog Devices

Analog Devices EZ-KIT Lite ADSP-BF538F Guía del usuario

Analog Devices

Analog Devices EVAL-AD5142ADBZ Manual de usuario

Analog Devices

Analog Devices AD9286-500EBZ Manual de usuario

Analog Devices

Analog Devices DC1198B-A Guía de configuración rápida

Analog Devices

Analog Devices ADZS-AD2428MINI Manual de usuario

Analog Devices

Analog Devices EVAL-ADuCM342EBZ Manual de usuario

Analog Devices

Analog Devices ADSP-2181 Manual de usuario

Analog Devices

Analog Devices AD5245 Manual de usuario

Analog Devices

Analog Devices UG-016 Manual de usuario

Analog Devices

Analog Devices AD8330 Manual de usuario

Analog Devices

Analog Devices EV-ADF4156SD1Z Manual de usuario

Analog Devices

Analog Devices DC2851A Manual de usuario

Analog Devices

Analog Devices EVAL-AD5341DBZ Manual de usuario

Analog Devices

Analog Devices EVAL-ADG788EBZ Manual de usuario

Analog Devices

Analog Devices DC2904A-B Manual de usuario

Analog Devices

Analog Devices ADuC7026 Suplemento

Analog Devices

Analog Devices AD9144-FMC-EBZ Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario