Analog Devices EVAL-ADUCM10QSPZ Manual de usuario

EVAL-ADUCM410QSPZ/EVAL-ADUCM410QSP1Z User Guide

UG-1541

One Technology Way •P. O. Box 9106 •Norwood, MA 02062-9106, U.S.A. •Tel: 781.329.4700 •Fax: 781.461.3113 •www.analog.com

ADuCM410 Development System: Getting Started Tutorial

Rev. 0 | Page 1 of 20

FEATURES

Interface through mIDAS-Link emulator

Power supply options: 9 V wall wart adapter, 5 V external

supply terminal block, or USB supply

ADuCM410 development system facilitates performance

evaluation of the ADuCM410 with a minimum of external

components

DEVELOPMENT SYSTEM KIT CONTENTS

EVAL-ADUCM410QSPZ or EVAL-ADUCM410QSP1Z evaluation

board

An Analog Devices, Inc., J-Link OB emulator (USB-SWD/

UART-EMUZ)

mIDAS-Link emulator

1 USB cable

DOCUMENTS NEEDED

ADuCM410 data sheet

ADuCM410 hardware reference manual

SOFTWARE NEEDED

ADuCM410 installer

MDIOWSD

Keil Vision5

IAR installer

IAR IDE software

GENERAL DESCRIPTION

The ADuCM410 is a fully integrated, single package device that

incorporates high performance analog peripherals together with

digital peripherals. The ADuCM410 features 16-bit, 2 MSPS data

acquisition on up to 16 input pins, an Arm® Cortex®-M33

processor, 12 voltage digital-to-analog converters (DACs), and

2 × 512 kB Flash/EE memory, packaged in a 5 mm × 5 mm, 81-ball

chip scale package ball grid array (CSP_BGA) and a 64-ball

wafer level chip scale package (WLCSP).

The ADuCM410 development system (EVAL-ADUCM410QSPZ

or EVAL-ADUCM410QSP1Z) is fully packaged to evaluate all

features of the ADuCM410, a high precision analog

microcontroller. The ADuCM410 includes 16 external AINx

channels, voltage output DACs (VDACs), four programmable

gain amplifiers (PGAs), measurement of the PGA current

channels, and various shared functions with the general-purpose

input/outputs (GPIOs) that are configurable through registers.

The VDAC channels generate an output range up to 2.5 V or

3.3 V full scale.

The EVAL-ADUCM410QSPZ and EVAL-ADUCM410QSP1Z

board uses a low noise, low dropout (LDO) linear regulator to

power up the device. The ADuCM410 is powered up using the

following three options: a 9 V wall wart adapter, a 5 V external

supply terminal block, and a USB supply.

This user guide describes how to configure the CSP_BGA

version (EVAL-ADUCM410QSPZ) and WLCSP version

(EVAL-ADUCM410QSP1Z) evaluation boards by providing

step by step procedures about the connections on the evaluation

boards. This user guide also contains information regarding

which evaluation versions of the third-party software tools to

download. Additionally, this user guide provides instructions on

how to load the supplied code examples. See Figure 1 for a

photograph of the EVAL-ADUCM410QSPZ board.

Following this guide allows users to generate and download

their own user code to use in their own unique end system

requirements.

Complete specifications for the ADucM410 are available in the

ADuCM410 data sheet, which must be consulted in conjunction

with this user guide when using the EVAL-ADUCM410QSPZ or

EVAL-ADUCM410QSP1Z board.

UG-1541 EVAL-ADUCM410QSPZ/EVAL-ADUCM410QSP1Z User Guide

Rev. 0 | Page 2 of 20

TABLE OF CONTENTS

Features .............................................................................................. 1

Development System Kit Contents ................................................ 1

Documents Needed.......................................................................... 1

Software Needed............................................................................... 1

General Description......................................................................... 1

Revision History ............................................................................... 2

EVAL-ADUCM410QSPZ Photograph........................................... 3

Evaluation Board Hardware............................................................ 4

Power Supplies and Default Link Options ................................ 4

Hardware Module............................................................................. 5

ADuCM410 and Arduino Power ............................................... 5

Arduino Connector...................................................................... 6

Getting Started .................................................................................. 7

Software Installation Procedures................................................ 7

Keil μVision5................................................................................. 7

CMSIS Pack in Keil μVision5 ......................................................8

Library and Project Options for ADuCM410 in Keil μVision5

..........................................................................................................9

IAR IDE Project Settings..............................................................9

mIDAS-Link Connector—Connecting the Hardware.......... 11

Evaluating the MDIO Download Mode.................................. 11

Evaluating the I2C Download Mode........................................ 12

Floating-Point Unit Enable Procedure .................................... 13

SRAM Mode Settings................................................................. 16

Safe Code Debugging/Development Recommendations.......... 19

Scenarios that Cause Device Lockups ..................................... 19

Recovering Locked Up Devices................................................ 19

Programmable Logic Array (PLA) Tool...................................... 20

Configuring the Gates and Output .......................................... 20

REVISION HISTORY

9/2020—Revision 0: Initial Version

EVAL-ADUCM410QSPZ/EVAL-ADUCM410QSP1Z User Guide UG-1541

Rev. 0 | Page 3 of 20

EVAL-ADUCM410QSPZ PHOTOGRAPH

20323-001

Digital I/Os

UART CONNECTOR

-LINK CONNECTOR

POWER TERMIN

BLOCK

9V WALL WART

AINx

VDACx

UART/USB MIDAS-LINK

Figure 1.

UG-1541 EVAL-ADUCM410QSPZ/EVAL-ADUCM410QSP1Z User Guide

Rev. 0 | Page 4 of 20

EVALUATION BOARD HARDWARE

POWER SUPPLIES AND DEFAULT LINK OPTIONS

The EVAL-ADUCM410QSPZ or EVAL-ADUCM410QSP1Z

development system can be powered with the following options:

a 5 V terminal block from bench supplies, a 9 V wall mounted

adapter, or a USB supply. See Table 1 for the on-board jumper

configurations for each power supply option and other optional

connectors. Locate Pin 1 for each header pin for the supply.

For any of the power supply options, place the jumpers shown

in Table 1 in the required operating setup before supplying

power to the EVAL-ADUCM410QSPZ or EVAL-

ADUCM410QSP1Z (see Figure 2).

Each power supply is decoupled to the relevant ground plane

with 10 μF and 0.1 μF capacitors. Each device supply pin is also

decoupled with a 10 μF and 0.1 μF capacitor pair to the relevant

ground plane.

EVAL-ADUCM410QSPZ/EVAL-ADUCM410QSP1Z Board

Interface

The ADuCM410 has on-chip digital peripheral interfaces, such

as a universal asynchronic receiver/transmitter (UART), serial

peripheral interface (SPI), management data input/output

(MDIO), and I2C. See Figure 1 for the on-board component

locations.

Bench Power Supply Option

The ADuCM410 requires 5 V for normal operation. Replicating

the jumper configuration in Table 1, the 5 V terminal block

supply passes through LDO regulators to regulate the power

supply. The ADuCM410 can also configure the IOVDD1 and

DVDD power supplies to be 1.2 V or 1.8 V, and 1.8 V or 3.3 V,

respectively. To configure these supply options, select the

required position on Jumper P11 for IOVDD1 and Jumper P15

for DVDD. P11 and P15 are on the solder side (bottom side of

the evaluation board.)

Table 1. Jumper Configurations for the EVAL-ADUCM410QSPZ and EVAL-ADUCM410QSP1Z

Jumper No. Optional Jumper Configuration Bench Supply or 9 V Wall Wart

JP6—Future Technology Devices

International (FTDI) Supply

No Short. Yes

JP7—USB Yes Short. Yes

P11—IOVDD1 No Pin 1 and Pin 2 = 1.8 V, Pin 2 and Pin 3 = 1.2 V. Yes

P15—DVDD No Pin 1 and Pin 2 = 3.3 V, Pin 2 and Pin 3 = 1.8 V. Yes

P7—SIN1 Level Shifter Yes Pin 1 and Pin 2 = IOVDD0, Pin 2 and Pin 3 = IOVDD1. Yes

P12—SOUT1 Level Shifter Yes Pin 1 and Pin 2 = IOVDD0, Pin 2 and Pin 3 = IOVDD1. Yes

P14—LED Display Yes Short. Yes

P5—IOVDD0 Pull-Up Yes Short. Yes

JP1—SWCLK Pull-Up Yes JP3, JP4, and JP5 are optional pull-ups. The R14 resistor

(see Figure 1) must be populated with values that are at

least 100 kΩ to use these optional pull-ups.

Yes

JP2—SWDIO Pull-Up Yes Short. Yes

JP3—P2.2 or SWO Pull-Up Yes Short. Yes

JP8 to JP10 Yes These pins use the on-board FTDI chip that can be used

on the I2C downloader.

Yes

+1.2

P11

+5V

DGND

LDOs

P15

+1.8

UART

ADuCM410

IOV

SB/WALL WART

MIDAS

LINK

AGND

SPI SPI

DGNDDGNDDGND

J-LINK

20323-006

Figure 2. On-Board Jumper Configuration Diagram

EVAL-ADUCM410QSPZ/EVAL-ADUCM410QSP1Z User Guide UG-1541

Rev. 0 | Page 5 of 20

HARDWARE MODULE

ADUCM410 AND ARDUINO POWER

Customers may want to connect their own custom circuits to

the EVAL-ADUCM410QSPZ or EVAL-ADUCM410QSP1Z

evaluation board.

Four connectors of the EVAL-ADUCM410QSPZ and EVAL-

ADUCM410QSP1Z evaluation boards support an Arduino®

Uno or Arduino Zero connection interface to external PCBs.

The EVAL-ADUCM410QSPZ/EVAL-ADUCM410QSP1Z

evaluation boards can power the external Arduino-based board.

Inversely, the Arduino is also capable of powering up the whole

module, including the ADuCM410. Table 2 shows the jumper

connections for the power configurations of the EVAL-

ADUCM410QSPZ/EVAL-ADUCM410QSP1Z and the

Arduino.

Table 2. Power Configurations for the EVAL-ADUCM410QSPZ (BGA) and EVAL-ADUCM410QSP1Z (WLCSP)

EVAL-ADUCM410QSPZ EVAL-ADUCM410QSP1Z Optional Jumper Information Jumper Configuration

P22 P20 Yes

Power selection either via

USB power or via Arduino

power

Pin 1 and Pin 2 = USB powered. Pin 2 and

Pin 3 = Arduino powered. Do not use USB

power for the EVAL-ADUCM410QSPZ or

EVAL-ADUCM410QSP1Z board if the

Arduino and the evaluation board are

powered up together.

JP16 JP16 Yes Power from Arduino via

the EVAL-ADUCM410QSPZ

or EVAL-ADUCM410QSP1Z

board

If this jumper is shorted, the

EVAL-ADUCM410QSPZ or

EVAL-ADUCM410QSP1Z also power up

the Arduino.

JP111JP111Yes 3.3 V LDO output Short.

JP121JP121Yes

3.3 V power to Arduino

IOREF pin

Short.

JP131JP131Yes

ADuCM410 reset to

Arduino reset

Short.

JP141JP141Yes 3.3 V power to Arduino Short.

JP151JP151Yes 5 V power to Arduino Short.

1The JP11 to JP15 connectors are used if the Arduino is powered up via the EVAL-ADUCM410QSPZ or EVAL-ADUCM410QSP1Z board.

UG-1541 EVAL-ADUCM410QSPZ/EVAL-ADUCM410QSP1Z User Guide

Rev. 0 | Page 6 of 20

ARDUINO CONNECTOR

The EVAL-ADUCM410QSPZ and EVAL-ADUCM410QSP1Z

have Arduino R3 headers directly compatible with Arduino

Uno and Arduino Zero. Using the EVAL-ADUCM410QSPZ

or EVAL-ADUCM410QSP1Z board with Arduino Uno or

equivalent is recommended. The Arduino pins used by the

EVAL-ADUCM410QSPZ or EVAL-ADUCM410QSP1Z board

are given in Table 3.

For more information on the ADuCM410 pins, refer to the

ADuCM410 data sheet and ADuCM410 hardware reference

manual (UG-1807).

Table 3. EVAL-ADUCM410QSPZ/EVAL-

ADUCM410QSP1Z Pin Connections to Arduino Pins

EVAL-ADUCM410QSPZ (CSP_BGA)/

EVAL-ADUCM410QSP1Z (WLCSP)

R3 Header Pins Arduino Pin

Digital

P13 (Both EVAL-ADUCM410QSPZ and EVAL-

ADUCM410QSP1Z)

P1.2/SCL1 SCL

P1.3/SDA1 SDA

AREF AREF

DGND GND

P0.0/SCLK0 SCK

P0.1/MISO0 MISO

P0.2/MOSI0 MOSI

P2.0 SS

P0.3/CS0 GPIO

P2.1/IRQ2 GPIO

P18 (EVAL-ADUCM410QSPZ) and

P16 (EVAL-ADUCM410QSP1Z)

P1.0/SIN1 RXD

P1.1/SOUT1 TXD

P0.6/SCL2 GPIO

P0.7/SDA2 GPIO

P1.4/SCLK1 GPIO

P1.5/MISO1 GPIO

P1.6/MOSI1 GPIO

P1.7/CS1 GPIO

EVAL-ADUCM410QSPZ (CSP_BGA)/

EVAL-ADUCM410QSP1Z (WLCSP)

R3 Header Pins Arduino Pin

P19 (EVAL-ADUCM410QSPZ) and

P18 (EVAL-ADUCM410QSP1Z)

P0.1/MISO0 MISO

IOVDD0 3.3V

P0.0/SCLK0 SCK

P0.2/MOSI0 MOSI

RESET RESET

DGND GND

Power

P20 (EVAL-ADUCM410QSPZ) and

P19 (EVAL-ADUCM410QSP1Z)

Arduino or ADuCM410 Power 7V VIN

AGND GND

Arduino or ADuCM410 Power 5V

Arduino or ADuCM410 Power 3V3

Arduino or ADuCM410 Reset RESET

Arduino or ADuCM410 Power IOREF

No Connect No connect

Analog

P21 (Both EVAL-ADUCM410QSPZ and EVAL-

ADUCM410QSP1Z)

AIN0 ADC5

AIN1 ADC4

AIN2 ADC3

AIN3 ADC2

AIN4 ADC1

AIN14 ADC0

EVAL-ADUCM410QSPZ/EVAL-ADUCM410QSP1Z User Guide UG-1541

Rev. 0 | Page 7 of 20

GETTING STARTED

SOFTWARE INSTALLATION PROCEDURES

Perform the following steps before plugging any of the USB

devices into the PC:

1. Close all open applications on the PC.

2. After downloading the ADuCM410 installer from

ftp://ftp.analog.com/pub/microconverter/ADucM410, double

click ADuCM410Installer-V0.1.0.0.exe and follow the

instructions shown in Figure 3. The ADuCM410-Installer

Setup window displays the installation method and

component selection as shown in Figure 3. The end user

license agreement (EULA) is displayed after proceeding

through the ADuCM410Installer Setup window. Accepting

the EULA extracts the installer, and rejecting the EULA

cancels the installer.

20323-002

Figure 3. Installation Options

3. After installation, the \AnalogDevices\ADuCM410 folder

opens. This location contains the examples folder that stores

the example codes for the ADuCM410 (see Figure 4).

20323-003

Figure 4. ADuCM410 examples Folder with Projects

KEIL µVISION5

The Keil μVision5® integrated development environment (IDE)

integrates all the tools necessary to edit, assemble, and debug

code. The fastest way to begin running the Keil IDE is to open

an existing project by using the following steps:

1. In Keil, click Project > Open Project.

2. Browse to the folder where the ADuCM410 software is

installed (C:\AnalogDevices\ADuCM410...).

3. Open the M410_GPIO.uvprojx file, located in the

ADuCM410\examples\M410_GPIO\ARM folder.

Opening the file launches an example project.

4. Set up the Cortex microcontroller software interface

standard (CMSIS) pack before proceeding through the

source. See the CMSIS Pack in Keil μVision5 section for

details on how to import the CMSIS pack.

5. Compile and download the source code to the EVAL-

ADUCM410QSPZ or EVAL-ADUCM410QSP1Z board

through the menu bar on the IDE.

6. To run the source code, press RESET on the EVAL-

ADUCM410QSPZ or EVAL-ADUCM410QSP1Z board

and then press RUN.

7. When running the code, the green LED on the board

marked DISPLAY flashes.

UG-1541 EVAL-ADUCM410QSPZ/EVAL-ADUCM410QSP1Z User Guide

Rev. 0 | Page 8 of 20

CMSIS PACK IN KEIL µVISION5

After the Keil μVision5® IDE is installed, open the application

and use the following steps to properly set up the ADuCM410

device from the IDE:

1. Open the CMSIS pack installer as shown in Figure 5.

When the pack installer is opened for the first time, it may

take a few minutes to update the pack installer.

20323-105

Figure 5. Pack Installer

2. After the CMSIS pack installer has opened, click File >

Import. Select and import the ADuCM410 pack that is

included in the installation setup (see Figure 6).

3. With the ADuCM410 CMSIS pack installed, the

ADuCM410 device is supported by the Keil μVision5 IDE.

The ADuCM410 appears in the Device tab of the Keil

window, as shown in Figure 7.

20323-106

Figure 6. Pack Installer

20323-107

Figure 7. ADuCM410 Device in Keil μVision5

EVAL-ADUCM410QSPZ/EVAL-ADUCM410QSP1Z User Guide UG-1541

Rev. 0 | Page 9 of 20

LIBRARY AND PROJECT OPTIONS FOR ADUCM410

IN KEIL µVISION5

The Keil μVision5 project files are placed in the Arm folder for

each example program. For example, C:\Analog Devices\

ADuCM410\examples\M410_Adc\ARM\M410_Adc.uvporjx

is the file that is opened by Keil. By clicking the Manage Run-

Time Environment icon from the Keil settings menu (see

Figure 8), users can select the components needed from

Peripheral Libraries in their project, as shown in Figure 10.

20323-108

Figure 8. Manage Run-Time Environment Icon

IAR IDE PROJECT SETTINGS

It is recommended for first time users to open an example

project from the examples folder. For instance, the

M410_Adc.eww file is the IAR Embedded Workbench® project

file for the ADC example, and it can be opened from the

C:\Analog Devices\ ADuCM410\examples\M410_Adc\IAR\

folder.

Opening an example file allows compilation, programming, and

debugging without any configuration changes from the user.

If creating a new IAR-based project, the following steps must be

completed to run the ADuCM410 example programs properly:

1. From the Project menu, select Options.

2. Click the General Options category, and ensure the

selected device is Analog Devices ADuCM410 under the

Target tab.

20323-110

Figure 9. IAR Project Setting

20323-109

Figure 10. Peripheral Libraries

UG-1541 EVAL-ADUCM410QSPZ/EVAL-ADUCM410QSP1Z User Guide

Rev. 0 | Page 10 of 20

3. After the ADuCM410 device is selected, click the Library

Configuration tab. Ensure that all settings match those

shown in Figure 11.

20323-111

Figure 11. IAR Library Configuration

4. Next, click C/C++ Compiler, and check that the

directories match those shown in the Additional include

directories box (see Figure 12).

20323-112

Figure 12. C/C++ Compiler Setting

5. Next, click the Linker category, check the Override default

box in the Config tab, and browse for the linker file under

the Linker configuration file section, as shown in

Figure 13.

20323-113

Figure 13. Linker Setting

6. Check the Debugger settings and ensure that all settings

match those shown in Figure 14 and Figure 15 in the

Download and Setup tabs.

20323-114

Figure 14. Debugger Configuration

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Microcontrolador de Analog Devices

Analog Devices

Analog Devices ADRV9001 Manual de usuario

Analog Devices

Analog Devices DC1840C Guía de configuración rápida

Analog Devices

Analog Devices ADuCM355 Guía rápida de usuario

Analog Devices

Analog Devices ADuCM4050 EZ-KIT Manual de usuario

Analog Devices

Analog Devices AN-951 Instrucciones de instalación y funcionamiento

Analog Devices

Analog Devices MicroConverter ADuC706x Hoja de especificaciones

Analog Devices

Analog Devices ADF7030-1 EZ-KIT Manual de usuario

Analog Devices

Analog Devices Linear Technology ADI Power DC3159A Guía de configuración rápida

Analog Devices

Analog Devices EV1HMC8362LP6G Manual de usuario

Analog Devices

Analog Devices EV-AD7284TMSDZ Manual de usuario

Analog Devices

Analog Devices ADuCM360 Manual de usuario

Analog Devices

Analog Devices Linear ADI Power DC3091 Manual de usuario

Manuales populares de Microcontrolador de otras marcas

AMS

AMS AS7261 Demo Kit Manual de usuario

Novatek

Novatek NT6861 Manual de usuario

Espressif Systems

Espressif Systems ESP8266 SDK Guía de configuración

Nuvoton

Nuvoton ISD61S00 ChipCorder Guía

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Manual de usuario

Texas Instruments

Texas Instruments Chipcon CC2420DK Manual de usuario

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Manual de usuario

NEC

NEC 78GK0S/K 1+ Series Instrucciones de instalación y funcionamiento

Mikroe

Mikroe SEMITECH N-PLC Click Instrucciones de instalación y funcionamiento

Intel

Intel Agilex Manual de usuario

Cypress

Cypress CY4607 HX2VL Manual de usuario

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Manual de usuario

Texas Instruments

Texas Instruments TMS320F2837 D Series Manual de usuario

CYPRES

CYPRES CY14NVSRAMKIT-001 Manual de usuario

Texas Instruments

Texas Instruments INA-DUAL-2AMP-EVM Manual de usuario

Espressif Systems

Espressif Systems ESP8266EX Instrucciones de funcionamiento

Abov

Abov AC33M8128L Manual de usuario

Laird

Laird BL654PA Manual de usuario