AMX DTMF+ Interface AXB-DTMF+ Manual de usuario

instruction manual

AXlink Bus Controllers

AXB-DTMF+

DTMF+ Interface

AMX Limited Warranty and Disclaimer

AMX Corporation warrants its products to be free of defects in material and workmanship under normal use for

three (3) years from the date of purchase from AMX Corporation, with the following exceptions:

• Electroluminescent and LCD Control Panels are warranted for three (3) years, except for the display and touch

overlay components that are warranted for a period of one (1) year.

• Disk drive mechanisms, pan/tilt heads, power supplies, MX Series products, and KC Series products are

warranted for a period of one (1) year.

• Unless otherwise specified, OEM and custom products are warranted for a period of one (1) year.

• Software is warranted for a period of ninety (90) days.

• Batteries and incandescent lamps are not covered under the warranty.

This warranty extends only to products purchased directly from AMX Corporation or an Authorized AMX Dealer.

AMX Corporation is not liable for any damages caused by its products or for the failure of its products to perform.

This includes any lost profits, lost savings, incidental damages, or consequential damages. AMX Corporation is not

liable for any claim made by a third party or by an AMX Dealer for a third party.

This limitation of liability applies whether damages are sought, or a claim is made, under this warranty or as a tort

claim (including negligence and strict product liability), a contract claim, or any other claim. This limitation of

liability cannot be waived or amended by any person. This limitation of liability will be effective even if AMX

Corporation or an authorized representative of AMX Corporation has been advised of the possibility of any such

damages. This limitation of liability, however, will not apply to claims for personal injury.

Some states do not allow a limitation of how long an implied warranty last. Some states do not allow the limitation or

exclusion of incidental or consequential damages for consumer products. In such states, the limitation or exclusion of

the Limited Warranty may not apply. This Limited Warranty gives the owner specific legal rights. The owner may

also have other rights that vary from state to state. The owner is advised to consult applicable state laws for full

determination of rights.

EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, AMX CORPORATION MAKES NO

OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. AMX CORPORATION

EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY

IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS

LIMITED WARRANTY.

Table of Contents

AXB-DTMF+ DTMF+ Interface

Table of Contents

Product Information .................................................................................................1

Specifications .................................................................................................................... 1

Configuration and Installation .................................................................................3

Setting the Internal Jumpers ............................................................................................. 3

Auto Answer mode................................................................................................................... 3

Line Setting mode .................................................................................................................... 4

Wiring the AXB-DTMF+..................................................................................................... 4

Preparing captive wires............................................................................................................ 4

Wiring guidelines...................................................................................................................... 4

Connecting External Telephone Lines .............................................................................. 5

Audio In ............................................................................................................................. 5

Audio Out .......................................................................................................................... 5

Testing the AXB-DTMF+ ................................................................................................... 6

Off-hook line and off-hook phone troubleshooting ................................................................... 6

Programming ............................................................................................................7

Send_Commands.............................................................................................................. 7

Operative Send_Commands.................................................................................................... 7

Timing System Send_Commands.......................................................................................... 10

Fine Tuning Send_Commands .............................................................................................. 14

Distinctive Ring Patterns and Send_Commands ............................................................ 15

Changing a Default Ring Pattern ........................................................................................... 16

Distinctive Ring Send_Commands......................................................................................... 17

Axcess Program Example ............................................................................................... 18

Channel Codes................................................................................................................ 22

Caller ID .......................................................................................................................... 24

Program Example for Caller ID .............................................................................................. 24

ii AXB-DTMF+ DTMF+ Interface

Table of Contents

Product Information

AXB-DTMF+ DTMF+ Interface

Product Information

The AXB-DTMF+ DTMF Interface (FIG. 1) links an Axcess central controller to a telephone

network, enabling dual tone multi-frequency (DTMF) and audio pass-through control. The AXB-

DTMF+, with a programmed central controller, processes incoming calls and initiates outgoing

calls to any pager or cellular phone.

The multi-function AXB-DTMF+ can be integrated for many imaginative and creative purposes

within a home or work environment using touch-tone control. For example, the AXB-DTMF+ can

announce callers by caller ID data, or can set up an audible menu selection to process incoming

calls for routing.

The audio pass-through can be used with an AXC-SPE Enhanced Speech Synthesizer card, or PC

sound card to produce audible menus, monitor phone audio, or provide audio input such as music

on hold. The AXB-DTMF+ allows a user to issue instructions to the AMX Central controller from

a remote location using any touch-tone telephone.

The AXB-DTMF+ receives and decodes DTMF audio signaling and sends the decoded data to the

central controller for the switching/controlling of any devices connected to the central controller.

An Axcess program written on a personal computer, and downloaded to the central controller,

enables the central controller to interpret the data received from the AXB-DTMF+. The program

may also issue menu selections over the telephone through an optional AXC-SPE card. For more

information about programming a central controller, refer to the Axcess Programming Guide.

Specifications

The following table lists the product specifications for the AXB-DTMF+.

AXB-DTMF+ Specifications

Power requirement 12 VDC

Power consumption 80 mA

DTMF+ Monitoring The AXB-DTMF+ can monitor DTMF signals only when in an off-hook state or

when a phone attached to the extension connection is taken off-hook.

Incoming signal detection • DTMF tones

•Ring

• Distinctive ring

•CallerID

Outgoing signal detection • DTMF tones

•Ring

•Busy

• Call termination

• Dial tone

Hardware state detection Detects if the AXB-DTMF+ is off-hook, or if the extension phone is off-hook.

Control Provides control for:

• AXB-DTMF+ off-hook/hangup

• Auto answer

• Extension phone on/disable

• Audio to telephone, and telephone to audio pass-through coupling

Product Information

2AXB-DTMF+ DTMF+ Interface

AXB-DTMF+ Specifications (Cont.)

Operation modes (set via

internal jumpers):

• Auto Answer

• Line Type

Refer to Setting the Internal Jumpers section on page 3 for details.

Front panel components (FIG. 1):

AXlink LED Blinks on and off to indicate that the AXB-DTMF+ is communicating with the

central controller.

Off Hook Phone LED Lights when ever a telephone connected to the PHONE connector on the AXB-

DTMF+ is in an off-hook condition.

The OFF HOOK PHONE LED only functions when the telephone line is con-

nected directly to the AXB-DTMF+.

Off Hook Line LED Lights when the AXB-DTMF+ is taken off-hook.

The OFF HOOK LINE LED only functions when the telephone line is con-

nected directly to the AXB-DTMF+.

Ring LED Lights when an incoming call ring is detected.

DTMF RX LED Lights when the AXB-DMTF+ is receiving DTMF signals.

DTMF TX LED Lights when the AXB-DMTF+ is transmitting DTMF signals out.

Rear panel components:

Phone connector This RJ-11 connector is used for attaching a telephone.

Line connector This RJ-11 input connects the incoming telephone line to the AXB-DTMF+.

Audio In RCA connector that provides unbalanced line level audio input signals for cou-

pling to the telephone line signals for coupling to the telephone line..

Audio Out RCA connector that provides an output for unbalanced line level (1V p-p) audio

signals coupled from coupled from the telephone line.

AXlink 4-pin captive-wire connector that provides power and communications with the

Axcess central controller.

Weight 1.0 lbs (454.0 g)

Dimensions (HWD) 1.51" x 5.55" x 6.45" (38.4 mm x 141 mm x 165 mm)

Mounting options • Flat mount

• Rack mount (using an optional AC-RK accessory rack kit).

FIG. 1 Front and rear views of the AXB-DTMF+

AUDIO

LINE

IN OUT

AXlink

AXM

GND

AXP

PWR

RING

HOOK

PHONE

OFF

HOOK

LINE

OFF

DTMF

DEVICE

PHONE

AXlink

Configuration and Installation

AXB-DTMF+ DTMF+ Interface

Configuration and Installation

Setting the Internal Jumpers

There are two 2-position jumpers on the AXB-DTMF+ circuit card (FIG. 1). Each jumper is set to a

default pin setting. These jumpers are positioned to enable automatic call answering and select line

setting for a leased line or phone operation.

Auto Answer mode

The 2-position jumper JP2 selects auto answer ON or OFF mode when the system powers on.

When the auto answer is on, the AXB-DTMF+ answers on the ring set by the Send_Command

COUNT-XXX. If the ring count is set to 3, for example, auto answer picks up the call after the

third ring. The default count is 1 ring. The default jumper setting is shown in FIG. 2.

To change the auto answer default from ON to OFF:

1. Remove the AXB-DTMF+ unit cover.

2. Remove the jumper from pins 2 and 3, and place it on pins 1 and 2.

3. Re-install the AXB-DTMF+ cover onto the unit housing.

FIG. 1 Location of JP1, JP2 jumpers, and Audio In potentiometer.

FIG. 2 Auto answer jumper JP2 (default setting = Auto Answer ON)

JP1

JP2

Audio In pot

JP1 - Line selection

JP2 - Auto Answer

front

pin 3

pin 2

pin 1

Auto Answer ON

Auto Answer OFF

Configuration and Installation

4AXB-DTMF+ DTMF+ Interface

Line Setting mode

The 2-position jumper JP1 selects PHONE or LEASED line operation when system powers on.

FIG. 3 shows the default setting.

To change the line setting default from PHONE to LEASED:

1. Remove the AXB-DTMF+ cover from the unit housing.

2. Remove the jumper from pins 2 and 3, and place it on pins 1 and 2.

3. Re-install the AXB-DTMF+ cover onto the unit housing.

Wiring the AXB-DTMF+

Preparing captive wires

To connect the wiring into a captive-wire connector:

1. Strip 1/4 inch off the wire insulation for all four wires.

2. Tin 2/3 of the exposed wire.

3. Insert each wire into the appropriate captive-wire connector up to the insulation.

4. Tighten the captive screws to secure the fit in the connector.

Wiring guidelines

The interface requires a 12 VDC power to operate properly. The interface uses a PSN2.8 power

suppl. The Central Controller supplies power via the AXlink cable or external 12 VDC power

supply. The maximum wiring distance between the Central Controller and interface is determined

by power consumption, supplied voltage, and the wire gauge used for the cable. The table below

lists wire sizes and maximum lengths allowable between the AXB-DTMF+ and Central Controller.

The maximum wiring lengths for using AXlink power are based on a minimum of 13.5 volts

available at the Central Controller’s power supply.

FIG. 3 Line Setting jumper JP1 (default setting = PHONE)

pin 3

pin 2

pin 1

Phone

Leased

If the device is using a separate power supply, do not connect the power wiring from

the AXB-DTMF+ to that device.

Wiring Guidelines at 80 mA

Wire Size Maximum Wiring Length

18 AWG 1467.14 feet (447.18 m)

20 AWG 928.22 feet (282.92 m)

22 AWG 578.70 feet (176.39 m)

24 AWG 364.79 feet (111.19 m)

Configuration and Installation

AXB-DTMF+ DTMF+ Interface

Connecting External Telephone Lines

Telephone cabling for both the input and extension lines are standard RJ-11 type connections.

Follow these steps to connect external telephone lines.

1. Check the circuit card jumper settings to match line type and auto answer mode. For more

information, refer to AXB-DTMF+ Jumpers in the Pre-Installation section of this manual.

2. Connect the AXlink cable to the Axcess Central controller AXlink input.

3. Connect the male RJ-11 jack of the incoming telephone line input to the AXB-DTMF+ LINE

jack and the extension telephone cable to the PHONE jack on the rear of the AXB-DTMF+.

4. Adjust the AUDIO OUT level by referring to the Audio Pass-Through Level paragraphs in this

section.

Audio In

The audio in is provided for music on hold or for voice menu selections if connected. If the audio

volume is too low or too high, the audio in level needs to be adjusted. Increase or decrease the audio

in pass-through level (gain) from the AXB-DTMF+. The AUDIO IN pot is located about mid-center

on the AXB-DTMF+ circuit board (see FIG. 1). Perform these steps to adjust the audio in level.

1. Remove the AXB-DTMF+ cover from the unit housing. Then, apply an audio signal (1 V p-p

maximum) to the AUDIO IN connector.

2. Listen on-line and use a small flat-blade screwdriver to turn the pot counter clockwise to

reduce audio level from AUDIO IN. Turn the pot clockwise to increase the AUDIO IN level.

3. Re-install the AXB-DTMF+ cover onto the unit housing.

Audio Out

The AUDIO OUT jack provides a means of routing line level signals, which originates on the

telephone line to an external device such as a sound card.

Cables and connectors for telephone and audio hook-up are not included with the

AXB-DTMF+.

If audio is connected to the AXB-DTMF+, make sure the audio is turned on by using

the correct Send_Commands. Refer to the Axcess Programming section.

To prevent "howling", make sure that the AXB-DTMF+ AUDIO IN and AUDIO OUT

lines are not looped back through an external device.

Configuration and Installation

6AXB-DTMF+ DTMF+ Interface

Testing the AXB-DTMF+

Follow these steps to test the AXB-DTMF+:

1. Disconnect AXlink power.

2. Remove the cover from the unit housing and set the AUTO ANSWER jumper to AUTO ANSWER

ON then reinstall the cover on the unit housing.

3. Reconnect AXlink power. The status LEDs should blink in sequence from right to left and the

AXlink green LED should be blinking.

4. Place a call to the AXB-DTMF+ from an outside line.

5. The RING LED should light with an incoming ring.

6. The OFF HOOK LINE LED should light after 1 ring.

7. The DTMF RX LED should light when tones are sent from the calling telephone.

8. Check line quality and operation using an extension telephone connected to the PHONE jack.

9. Return the AUTO ANSWER jumper to OFF position, if desired.

Off-hook line and off-hook phone troubleshooting

The off-hook line and off-hook phone LEDs light only if there is a good telephone line connection.

If either the off-hook line or off-hook phone LED fails to light, a faulty telephone line connection is

indicated.

Make sure a proper phone line connection exists to light both off-hook and extension off-hook

LEDs. Test the off-hook line by following these test procedures:

1. Take the AXB-DTMF+ off-hook by issuing the off-hook Send_Command from the central

controller. If there is a good telephone line connection, then the OFF HOOK LINE LED lights.

2. If the OFF HOOK LINE LED fails to light, then there is a bad or faulty telephone line

connection. Check the incoming telephone line and make sure it is working properly. Then,

check the RJ-11 cable and its connection to the AXB-DTMF+.

Test the off-hook phone using the following steps:

1. Take the receiver off the extension telephone. If there is a good telephone line connection, then

the EXTENSION OFF HOOK LED lights.

2. If the OFF HOOK PHONE LED fails to activate, make sure that an extension off-hook

Send_Command has not been issued (you can do a Send_Command extension on-hook to be

sure; see the Operative Send_Commands section on page 7 for details). If this does not

produce results, then there is a faulty telephone line connection. Check the incoming telephone

line and make sure it is working properly. Then, check the RJ-11 cable and its connection to

the AXB-DTMF+. Make sure the RJ-11 cable from the extension telephone is good.

The extension telephone is optional and supplied by the user.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Tarjeta de red de AMX

AMX

AMX NetLinx Master-Ethernet Card/Module... Manual de usuario

AMX

AMX NetLinx Integrated Controller NI-900 Manual de usuario

AMX

AMX NetLinx Integrated Controller NI-2100 Manual de usuario

AMX

AMX NetLinx Master Card NXC-ME260-64 Manual de usuario

AMX

AMX netlinx NXC-IRS4 Manual de usuario

AMX

AMX NetLinx Master Card NXC-ME260-64 Manual de usuario

AMX

AMX Mi-Series Network Interface Card DAS-MNET Manual de usuario

AMX

AMX AXP-AI8 ANALOG 8-INPUT BOARD Manual de usuario

AMX

AMX NXC-I/O10 Manual de usuario

AMX

AMX AXB-EM232 Manual de usuario

AMX

AMX NXA-ICSNET Manual de usuario

AMX

AMX AXC-PTSM Guía

AMX

AMX AXC-INP8 Manual de usuario

AMX

AMX NetLinx Custom Panel Interface NXP-CPI16 Manual de operación y mantenimiento

AMX

AMX ICSNet Daughter Card NXA-ICSNET Manual de usuario

AMX

AMX NetLinx Master Card NXC-ME260-64 Manual de usuario

AMX

AMX modero NXA-WC80211B Manual de usuario

AMX

AMX NetLinx NXM Series Manual de lista de piezas

AMX

AMX Zero Cross Module RDM-ZC50 Instrucciones de montaje

AMX

AMX NetLinx Master-Ethernet Card/Module... Manual de usuario

AMX

AMX AXC-INP8 Manual de usuario

AMX

AMX AXlink Bus Controllers AXB-232++ Manual de usuario

AMX

AMX NetLinx Master-Ethernet Card/Module... Guía

AMX

AMX NetLinx Integrated Controller NI-700 Manual de usuario

Manuales populares de Tarjeta de red de otras marcas

FirstComm

FirstComm OBiWiFi5G Manual de usuario

Sun Microsystems

Sun Microsystems Interface Adapter Manual de usuario

TRENDnet

TRENDnet TU2-ETG Manual de usuario

YASKAWA

YASKAWA SI-EN3 Manual de usuario

Paradyne

Paradyne BitStorm 2600 IP DSLAM Manual de usuario

Belkin

Belkin F5D7050 Manual de usuario

3Com

3Com EtherLink 3C509B Manual de usuario

TRENDnet

TRENDnet TEG-PCITX Manual de usuario

Cisco

Cisco MC16E Manual de usuario

Delta Electronics

Delta Electronics Braking Modules VFDB Series Manual de usuario

TwinMOS

TwinMOS Booming Manual de usuario

Dialogic

Dialogic Media Board DM/V1200BTEPEQ Manual de usuario

Buffalo

Buffalo AirStation WLI-PCM-L11GP Manual de usuario

National Instruments

National Instruments NI 9234 Manual de usuario

Hama

Hama 49276 Manual de usuario

Linksys

Linksys WCF54G - Wireless-G Compact Flash Card Manual de operación

Compaq

Compaq Wireless LAN 100 Manual de usuario

Bose

Bose PowerMatch Dante Manual de usuario