AMX Phast PLL-SD10 Manual de usuario
Page 1of 3 08/07/00 Rev. C
User Guide
Model PLL-SD10 Smart Dimmer
Description
The PLL-SD10 is a solid state, microprocessor-controlled
dimmer. Before the network is applied, the PLL-SD10 can control
the load with a default feature set.
If the button is pressed and released, the PLL-SD10 will
automatically ramp to its full on or off state. If the button receives
another push and release before the final state has been reached,
the PLL-SD10 will halt at that point in the load curve.
When the button is pressed and held, the PLL-SD10 will begin to
ramp slowly to its full on or off state. When released, it will halt at
that point in the load curve.
By default, the LED on the button of the PLL-SD10 is off when
the load is off, and is on when the load is on.
When the PLL-SD10 is connected to the PHASTLink network, the
following features are available for programming:
•LED Brightness and On/Off State
•Ramp Rate Adjust
•Network-Controlled Lighting Scenes
•Maximum On Level
•Push and Hold Delay
•Detachable Button (push/hold/release)
Electrical Specifications
•Max Load 600 Watts
••Supply 120 VAC, 60 Hz
•Interface PHASTLink
Junction Box Requirements
Maximum Number of Conductors
Box Dimensions (inches) Min. Cu. In.
Capacity No. 18 No. 16 No. 14 No. 12 No. 10 No. 8 No. 6
3 x 2 x 2 1/2 12.5 8765542
3 x 2 x 3 1/4 14.8 9876542
3 x 2 x 3 1/2 18.0 12 10 98763
Installation
WARNING! DANGEROUS VOLTAGE!
To reduce the risk of serious injury or death, turn all power off before installing this equipment.
WARNING!
PHAST lighting products generate heat. They should only be installed in room-temperature
(approx. 77°F, 25°C) indoor environments. Installing these products in attics, closets, or other
confined areas with inadequate ventilation or heat dissipation ability has the potential to cause
overheating and a possible fire hazard, and will void the warranty.
1. Connect the black (hot) wire to the line voltage (see Figures 2 and 3).
2. Connect the white (common) wire to neutral.
3. Connect the red wire to the load (incandescent lights, up to 600 watts).
Figure 1 -PLL-SD10
Page 2of 3 08/07/00 Rev. C
4. Connect the green wire to ground.
5. The blue wire is a low-voltage tap to connect up to seven PHAST PLL-3WAY switches (see
Figures 2 and 3).
6. Make sure the RJ-45 connectors have been correctly installed on the PHASTLink cables and
insert the RJ-45 connectors in the RJ-45 jacks on the back of the PLL-SD10 (see Figure 3).
Make sure the connectors are fully seated in the jacks.
Note: The PLL-3WAY switch also has RJ-45 jacks, but these have no connection to any
internal circuitry in the PLL-3WAY. The RJ-45 jacks on the PLL-3WAY are only
provided as a convenient means of continuing a PHASTLink line through a junction
box that contains a PLL-3WAY. Refer to the PLL-3WAY documentation for details.
7. For optimum performance, we recommend the installation of a double 120-ohm terminator in
one of the RJ-45 jacks of the last device (or the only device) in a chain of PHASTLink
devices.
To build a double 120-ohm terminator:
a. Install a 120-ohm resistor between pins 1 and 2 of an RJ-45 connector. See Figure 4 for
RJ-45 pin numbers.
b. Install a 120-ohm resistor between pins 7 and 8 of the same RJ-45 connector.
Note: Use ¼-watt or larger resistors.
8. Make sure there is a minimum 0.25-inch gap between all high-and low-voltage components.
9. Remove the plastic face plate and mount the PLL-SD10 in the junction box.
10. Screw the PLL-SD10 to the junction box through the mounting slots.
Note: For multi-gang installations, break off the metal corner tabs on the metal heat sink.
The outer tabs on the end devices may be left intact. Up to five PLL-SD10 units can
be mounted in a single multi-gang junction box without de-rating the load capacity.
CAUTION!
To avoid damaging this device and voiding the warranty:
•DO NOT connect the ground wire (green) or the 3-way control wire (blue) to the hot, load,
or neutral wires.
•DO NOT short the load wire (red) to the ground, common, or 3-way control wires.
Figure 2 -Wiring Diagram
RJ-45
PHASTLink
Neutral
Page 3of 3 08/07/00 Rev. C
Troubleshooting
Problem: LED does not come on at power-up.
1. Check the voltage across the Hot and Common wires to make sure the device is getting
power (should be 120VAC).
2. Make sure the 3-way Control wire is not shorted to Ground. If this wire is shorted, the device
may appear in Landmark Designer, but it will not operate via the button.
Problem: Dimmer works, but does not appear in Landmark Designer.
1. Check the PHASTLink cable.
2. Make sure the device's Ground wire is properly grounded and NOT shorted to Common,
Load, or Hot wires.
Technical Support
Note: There are no user-serviceable parts inside the device. Opening the device will
void your warranty and may expose you to dangerous voltages.
If you experience problems with your PHAST products, double check all external connections,
settings. If the problem persists, call your PHAST dealer or PHAST Technical Support.
•Write your PHAST dealer's number here for easy
reference:___________________________
•You can contact PHAST Technical Support at 800-979-9637 or 801-264-8090.
•Support is also available at the PHAST web site at http://phast.com
PHAST Corporation
79 West 4500 South, Building 14
Salt Lake City, Utah 84107
801-264-8090
800-979-9637
801-264-8271 FAX
http://phast.com
Figure 3 -Rear View of PLL-SD10
1
2
3
4
5
6
7
8
Figure 4 -RJ-45 Plug
(neutral)
Tabla de contenidos
Otros manuales de Regulador de intensidad de AMX
AMX
AMX Dual Incandescent Dimmer Module RDM-2INC Instrucciones de montaje
AMX
AMX Triple DC Dimmer Module RDM-3DC Manual de usuario
AMX
AMX Radia Eclipse RE-DM4 Manual de usuario
AMX
AMX Incandescent Dimmer Module RDM-INC50 Instrucciones de montaje
AMX
AMX ALD-D48 Instrucciones de uso
AMX
AMX RDM-INC Guía de inicio rápido
AMX
AMX RDD-DM4 4-CHANNEL INTEGRATED DIMMER MODULE Manual de usuario
AMX
AMX RDD-DM6 6-CHANNEL INTEGRATED DIMMER MODULE Manual de usuario
AMX
AMX RDM-2INC Guía de inicio rápido
AMX
AMX RDM-3DC Manual de usuario
AMX
AMX RDM-2DC Manual de usuario
AMX
AMX RDM-2INC Instrucciones de montaje
AMX
AMX RDM-DC DC MODULE Instrucciones de montaje
AMX
AMX ALD-1000D Manual de usuario
AMX
AMX RDM-3DC TRIPLE DC MODULE, 1,920 W (X3), 0-12... Instrucciones de montaje
AMX
AMX RDM-3FDB TRIPLE FDB MODULE Instrucciones de montaje
AMX
AMX Radia Eclipse RE-DM4 Manual de usuario
AMX
AMX RDM-MDM Manual
AMX
AMX PRO-2400 Manual de usuario
AMX
AMX RDM-2FDB DUAL FDB MODULE, 1,920 W (X2) Instrucciones de montaje
