Lex 6KW Manual de usuario

6KW,12KW and 24KW

Portable Dimmers

User Guide

REV009

www.lexproducts.com

[email protected]

800.643.4460

Lex Products Corporation

15 Progress Drive

Shelton, CT 06484

203.363.3738

203.363.3742 Fax

Lex West

11847 Sheldon Street

Sun Valley, CA 91352

818.768.4474

818.768.4040 Fax

Table of Contents

Introduction .............................................................................................................................................................. 3

Safety Notice............................................................................................................................................................. 3

Installation ................................................................................................................................................................. 4

Set-Up and Operation............................................................................................................................................ 5

Maintenance ............................................................................................................................................................. 6

Troubleshooting ...................................................................................................................................................... 6

Technical Support ................................................................................................................................................... 6

Additional Resources ............................................................................................................................................. 7

Extra Notes................................................................................................................................................................. 7

This user guide is furnished exclusively to support installation and operation of the Lex 6KW, 12KW and 24KW

portable dimmers. All concepts and ideas are the sole property of Lex Products and are not to be duplicated or utilized in

any manner without written permission.

LEX User Guide

6KW, 12KW and 24KW Portable Dimmers

www.lexproducts.com 3

Introduction

The 6KW, 12KW and 24KW portable dimmers comprise a unique portable dimming solution that can be used

individually or as part of a dimming system. This product range is ideally suited for:

• MotionPicturesets

• TelevisionProduction

• Studios

• On-location

Features and Beneﬁts of the 6KW, 12KW and 24KW portable dimmers

• Worksasadimmeroron-offrelay

• Fullydigital,pushbuttonlevelsettingcontrolaswellastraditionalslider

for setting control level

• DMX512-Acontrolthrough5-pinXLRinputandoutput

• Digitaldisplayshowstheselecteddimmerlevelfrom0-100%,lamppre-heatlevelfrom0-25%,

 relayassignment/functionandDMX512-Aaddressfrom001-512

• SeparateLEDsindicateoperatingmodesandpresenceofDMX512controlsignal

• LEDindicatorsshowstatusofcircuitbreakerandoutputvoltage

• Powerfailmemory–retainsdimmerlevel,pre-heatlevel,operatingmodeandDMX512address

• Modularpanelincorporatingmicroprocessor-basedcontrolelectronicsforprecision

• 100%solidstatedesignforreliability

• 8-bitresolutionallowsfull256-stepdimmingcontroltoensureexactlevelrepeatability

• Circuitbreakerprotected

• Voltageregulationmaintainsdimmeroutputwithin2%despiteuctuationsininputvoltage

• Panelmountstagepinconnectorsforinputandoutput

Safety Notice

EquipmentmanufacturedbyLexProductsisbuiltandtestedwithsafetyasaprimaryconsideration,howeverelectrical

equipmentmustbeusedwithcareandinstalledbyqualiedpersonnel.Observeallnormalprecautionswhenoperating

this unit.

• Reviewallinstructionsbeforeuseandsaveforfuturereference

• Thisproductmustbeproperlygrounded

• Thisproductisforuseindrylocationsonly

• Ifoperatingthisunitlyingonit’sside,ensuretheheatsinksidefacesup

• Unplugunitfrompowerbeforeservicing

• Donotmodifydimmerorhousinginanymanner

• Do not drop dimmer

Lex Products hereby disclaims any and all liability for any injury or damage caused by the faulty installation or improper

operation of this product, including damage from mishandling.

Note: Canadian versions of the Lex FD1 ﬁlm series dimmers are also available. These products differ only in the use of

CanadianindustrystandardJoyandSeries18Cam-typepowerconnectors.

Installation

Location

Place the 6KW, 12KW and 24KW portable dimmers in a ventilated area free of excessive humidity or condensation and accessible

only to authorized personnel. Typical ambient temperature should be between 0° and 32° C.

Connecting Power and Control Wiring

TheFD1-6Kdimmerisratedfor6,000Wattsat120VAC.Itequippedwitha60AmpStagePin

plug for power input (60 Amp Joy pigtail in Canada) and is protected by a 50 Amp magnetic

circuitbreaker.TheFD1-12Kisratedfor12,000Wattsat120VAC.Itisequippedwitha100

AmpStagePinplugforpowerinput(Series18Cam-typepigtailinCanada)andisprotected

bya100Ampmagneticcircuitbreaker.

TheFD1-24Kdimmerisratedfor24,000Wattsat240VAC.Itisequippedwitha100AmpStagePin

plugforpowerinput(Series18Cam-typepigtailinCanada)andisprotectedbya2-pole,

100Ampmagneticcircuitbreaker.

Turn the circuit breaker labeled “Mains Power” off

before making any connections to the dimmer.

Line:ConnecttheFD1-6KorFD1-12Kpanelmountedpowerinputplugtoabranchcircuitprotected120VAC,60Hz

power source using a cable that is properly grounded and appropriately rated.

Theacceptableinputvoltagerangeforthisunitis95-130VAC.

ConnecttheFD1-24Kpanelmountedpowerinputplugtoabranchcircuitprotected240VAC,

60Hzpowersourceusingacablethatisproperlygroundedandappropriatelyrated.Theac-

ceptableinputvoltagerangeforthisunitis190-240VAC,soa208VAC,60Hzpowersource

may be used.

When the power connections are secure, the dimmer may be energized by turning on the

MainsPowerbreaker.Shouldthebreakertrip,checkthepowersourceandcablesbeingused

before resetting. Do not power any of the units from a dimmed circuit.

Load: The 6KW, 12KW and 24KW portable dimmers can control incandescent and inductive

loadsincludinglamps,fansandmagnetictransformersinthedimmode.Intherelaymode,

itprovidesafullsine-waveoutputandcancontroladditionalloadtypes,howevercaremust

betakentoassurethatnondimmableloadsareonlyoperatedintherelaymode.Besureto

include transformers in load calculations.

Forsafety,andtoavoidthewearandtearassociatedwithhotpatching,theMainsPowercircuit

breakershouldbeswitchedoffbeforeconnectingtheload.Toprolonglamplife,setthecontrol

outputtozeroorapre-heatlevelbeforeenergizingtheload.Plugload(s),uptothecapacityofthedimmer,intothepower

output receptacle using properly grounded and appropriately rated cables.

Control:ForcontrolusingUSITTDMX512-Adataprotocol,plugcontrolcablesconstructedforthisuseintothe5-pin

XLRconnectorslabeled“DMX512In”and“DMX512Thru”(ifcableruncontinuesbeyondthisunit).DMX512rules

requiretheuseofaplug-interminatoronthelastunitinaDMXdaisychain.Theterminationplugshouldbepluggedinto

the“DMX512Thru”receptacle.

Note:FD1unitsarenotself-terminating.

TheLEDonthecontrolpanellabeled“DMXData”willIlluminatewhencontroldataispresent.

LEX User Guide

6KW, 12KW and 24KW Portable Dimmers

MAINS POWER INPUT

MAINS POWER

OFF ON

DIMMER OUTPUT

Set-Up and Operation

The control panel will be operational once main power is present to the dimmer, regardless of the position of the main

circuitbreaker.Thisfeatureenablesoperatorstosetappropriatecontroloutputparameterspriortoenergizingthedimmed

load.

The6KW,12KWand24KWportabledimmersoperatorinterfaceconsistsofathree-digitLEDdisplay,threemomentary

pushbuttonsandfourLEDindicatorstoreporttheset-up/operatingmodeselected.Modesare:Manual,Relay,DMXand

Pre-heat.Eachmodeisexplainedbelow.

Mode selection:Toselectamodepressthecenterpushbuttonlabeled“Function.”TheLEDindicatorsabovethedisplay

will incrementally illuminate to indicate the mode selected. Press the button again to step to another function.

Manual: The manual mode allows the unit to be used as a

selfcontrolleddimmer.Whenthe“Man”LEDisilluminated,usethe“Inc”and

“Dec”pushbuttonstoraiseandlowerthelightingtothedesiredlevelfrom0to

100%outputvoltage.A60mmsliderisalsoprovidedtosetadesiredoutput

level.The%outputlevelwillbereportedonthedisplayover-ridinganypre-set

(pushbutton)level,toincrementby1%usepushbuttons(highesttakesprior-

ity).

DMX:TheDMXfunctionallowstheunittobeoperatedremotelyusingUSITT

DMX512-Adataprotocol.Whenthe“DMX”LEDisilluminated,usethe“Inc”

and“Dec”pushbuttonstoassignaDMX512address(001to512).Theaddress

willbedisplayedandheldinmemoryuntilchanged.Thedimmer’soutputwillbeasquare-lawdimmingcurvepropor-

tionaltotheDMX512controlsignalbeingreceivedatanymoment.Ifthecontrolsignalisremovedorinterrupted,theunit

willholdthelastlevelreceiveduntilthecontrolsignalisrestoredoruntilpowerisreset.TheGreenDMXDATALEDwill

illuminate with the precence of data at the input connectors.

Relay: Therelaymodeallowstheusertoswitchany120VAC(FD1-6KandFD1-12K)or240VAC(FD1-24K)xture

or device (up to the capacity of the unit) on and off. The relay function may be controlled locally by the pushbuttons or

remotelyviaDMX512.Toactivatetherelaymode,whenthe“Relay”LEDisilluminated,pressthe“Inc”pushbuttononceto

turnthefunctiononandenableremotecontrol.ThedisplaywillindicatetheDMX512addresstowhichtheunitis

assignedtorespond.Toswitchtherelaylocally,pressthe“Inc”pushbuttonagain.Thedisplaywillindicate“ON”andthe

loadwillimmediatelyturnon.Toswitchtheloadoff,pressthe“Dec”pushbuttononce,returningtotheDMX512address.

Pressthe“Dec”pushbuttonagaintoturnofftherelayfunctionentirely.Whenturnedoff,thedisplaywillbeblank.

Pre-heat:Thepre-heatfunctionallowstheusertowarmthelamentofalargeincandescentlampby

providingasmallACvoltagefromthedimmeroutput.Thelevelforthisfunctionmaybesettoavalueof0-25%ofthe

inputlinevoltage.Whenthe“Pre-heat”LEDisilluminatedusethe“Inc”and“Dec”pushbuttonsto

assignthepreferredpre-heatlevel.Thenreturntheunittomanual,DMXorrelaymodeforoperation.The

Pre-heatlevelwillremainattheprogrammedlevelunlesschangedbytheoperator.ThePre-heatLEDwillremainillumi-

natedtoremindtheuserthatthereisaPre-heatlevelisassignedinmemory.Toremovethislevel,

visitPre-heatmodeonceagainandusethedecreasebuttontosetto0.

Operating:Beforeoperatingthedimmer,checktoseethattheMainsPowercircuitbreakerison.Whenthedimmerisin

manualmodeitwillignoreanyDMX512signalthatmaybepresent.Forremoteoperation,besuretheunitisinRelayor

DMXmodeandthatavalidDMX512controlsignalispresent.Thedimmerisdesignedwithpower-failmemory.Whenthe

unit is powered up, it will return to the last mode of operation and will retain previously programmed information.

www.lexproducts.com 5

Maintenance

The 6KW, 12KW and 24KW portable dimmers are designed to be low maintenance; however, several precautionary steps will

prolongthelifeoftheelectroniccomponents.Wheneverpossible,limittheunit’sexposuretohighambienttemperatures.Take

carenottodropthedeviceandalwaysprotectthecontrolsandconnectorsfromdamage.Donotallowliquidofanykindtoenter

the unit.

Allscrewsandconnectionsshouldbechecked,andtightenedifnecessary,onaregularbasis,especiallyinrentalandlocation

applications.Iftheunitaccumulatesdust,disconnectitfrompowerandcleanitusingcompressedair.Alwaysdisconnectdimmer

from power before performing any maintenance operation.

Troubleshooting

Iftheportabledimmerdoesnotoperateasexpected,checkthepowersourceandcheckallcablesandconnectors.Besurethe

MainsPowercircuitbreakerison.Conrmthatthecontrolledloadoperatesfromaconstantpower

supplyandconrmthatanyremoteconsoleissendingvalidDMX512-Adata.

Control indicators do not illuminate: Conﬁrm that power is present to the unit.

Inc and Dec buttons do not raise and lower the lighting level:MakesurethedimmerisinManualmode

(pressandholdFunctionbuttonuntilManualLEDilluminates).

Unit does not respond to remote DMX512 input:CheckallcontrolcablingandcheckthatDMXDataLEDis

illuminatedtoindicatepresenceofcontrolsignal.MakesurethatdimmerisinDMXorRelaymode(pressandholdFunction

buttonuntiloneoftheseLEDsilluminates).

Connected load switches on and off instead of dimming:ConrmthatRelaymodeisactivated.PressandholdFunction

buttonuntilRelayLEDilluminates.IfaDMX512addressisdisplayed,Relayfunctionisactive.TodeactivateRelayfunction,press

Decpushbutton.Displayshouldgoblanktoindicateareturntodimmingoperation.

The dimmer does not respond to the user controls – Inc, Function, Dec:ResettheelectronicsbypressingtheReset

button on the rear of the unit.

Connected load is ghosting and will not shut off:Apre-heatlevelhasbeensetandisretainedinmemory.

CycletheFunctionbuttonuntilthepre-heatLEDilluminatesandusetheDecbuttontoresetthepre-heatleveltozero.Usethe

FunctionbuttontoreturntoManualorDMXmode.

Load is stuck on and does not dim or switch off:ChecktoseeifRelaymodeisactivatedandtherelayhasbeenturned

onmanually.PressandholdFunctionbuttonuntilRelayLEDilluminates.Ifthedisplayshows“ON”therelayhasbeenturnedon

manually.PresstheDecbuttontoturntherelayOFF.Iftheloadremainson,thepowerdevicemayhavefailed.ContactTechnical

Servicesat1.855.LEX.1002

Technical Support

ThestaffatLexProductsiswillingandavailabletohelpinanywaypossible.Ifyouhavequestionsorneed

technicaladviceorsuggestionsregardingthisproduct,pleasecontactLexat1.855.LEX.1002ore-mailLexat

[email protected].BusinesshoursareMondaythroughFriday,8:30am–5pm.Inaddition,TechnicalServices

is available 24/7 via phone.

LEX User Guide

6KW, 12KW and 24KW Portable Dimmers

www.lexproducts.com 7

Additional Resources

ForadditionalinformationregardingtheDMX512controlprotocol,properlyknownas“ANSIE1.11-

2004EntertainmentTechnology-USITTDMX512-A-AsynchronousSerialDigitalDataTransmission

StandardforControllingLightingEquipmentandAccessories”visitthefollowingsites:

• ANSI(AmericanNationalStandardsInstitute),www.ansi.org

• USITT(UnitedStatesInstituteforTheatreTechnology),www.usitt.org

• ESTA(EntertainmentServicesandTechnologyAssociation),www.plasa.org

Extra Notes

1-800-643-4460 • www.LexProducts.com • info@LexProducts.com 8

Lex Products Corporation

15 Progress Drive

Shelton, CT 06484

203.363.3738

203.363.3742 Fax

Lex West

11847 Sheldon Street

Sun Valley, CA 91352

818.768.4474

818.768.4040 Fax

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Regulador de intensidad de Lex

Lex

Lex Slim Dimmer Manual de usuario

Manuales populares de Regulador de intensidad de otras marcas

ZooZ

ZooZ ZEN54 LR Manual de usuario

DIODE LED

DIODE LED TOUCHDIAL Mini Manual de usuario

Viessmann

Viessmann 5590 Manual de usuario

American DJ

American DJ DP-8A Manual de usuario

Teleco

Teleco TVSTICK868RGB29 Manual de usuario

INSTEON

INSTEON LampLinc 2457D2 Manual de usuario

LEGRAND

LEGRAND WattStopper RH703PTU Manual de usuario

ADB

ADB EURODIM TWIN TECH Manual de usuario

Sinope

Sinope DM2550ZB-C4 Manual de usuario

SkyLink

SkyLink SK7 Manual de usuario

Makel

Makel RC Manual de usuario

Lightronics

Lightronics XC-62 Manual de usuario

Triton Blue

Triton Blue DM-1225 Manual de usuario

ETC

ETC ES750 Instrucciones de funcionamiento

NA OMEGA + Manual de usuario

GE ZB3001 Manual de usuario

LSC

LSC DP-1210 Manual de usuario

Leviton

Leviton DDS8800 Instrucciones de funcionamiento