Amprobe TMA10A Manual de usuario

TMA10A

Anemometer

User Manual

ENG FRE SPA

GER ITA

TMA10A

Anemometer

User Manual

6/2018, 6011186 Rev B

English

Limited Warranty and Limitation of Liability

Your Amprobe product will be free from defects in material and

workmanship for one year from the date of purchase unless local

laws require otherwise. This warranty does not cover fuses, disposable

batteries or damage from accident, neglect, misuse, alteration,

contamination, or abnormal conditions of operation or handling.

Resellers are not authorized to extend any other warranty on the

behalf of Amprobe. To obtain service during the warranty period,

return the product with proof of purchase to an authorized Amprobe

Service Center or to an Amprobe dealer or distributor. See Repair

Section for details. THIS WARRANTY IS YOUR ONLY REMEDY. ALL

OTHER WARRANTIES - WHETHER EXPRESS, IMPLIED OR STATUTORY

- INCLUDING IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR

PURPOSE OR MERCHANTABILITY, ARE HEREBY DISCLAIMED.

MANUFACTURER SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT,

INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES, ARISING

FROM ANY CAUSE OR THEORY. Since some states or countries do

not allow the exclusion or limitation of an implied warranty or of

incidental or consequential damages, this limitation of liability may not

apply to you.

Repair

All Amprobe returned for warranty or non-warranty repair or for

calibration should be accompanied by the following: your name,

company’s name, address, telephone number, and proof of purchase.

Additionally, please include a brief description of the problem or the

service requested and include the test leads with the meter. Non-

warranty repair or replacement charges should be remitted in the

form of a check, a money order, credit card with expiration date, or a

purchase order made payable to Amprobe.

In-warranty Repairs and Replacement – All Countries

Please read the warranty statement and check your battery before

requesting repair. During the warranty period, any defective test tool

can be returned to your Amprobe distributor for an exchange for the

same or like product. Please check the “Where to Buy” section on

amprobe.com for a list of distributors near you. Additionally, in the

United States and Canada, in-warranty repair and replacement units

can also be sent to an Amprobe Service Center (see address below).

Non-warranty Repairs and Replacement

– United States and Canada

Non-warranty repairs in the United States and Canada should be sent

to an Amprobe Service Center. Call Amprobe or inquire at your point

of purchase for current repair and replacement rates.

USA: Canada:

Amprobe Amprobe

Everett, WA 98203 Mississauga, ON L4Z 1X9

Tel: 877-AMPROBE (267-7623) Tel: 905-890-7600

Non-warranty Repairs and Replacement – Europe

European non-warranty units can be replaced by your Beha-Amprobe

distributor for a nominal charge. Please check the “Where to Buy”

section on beha-amprobe.com for a list of distributors near you.

Beha-Amprobe

Division and reg. trademark of Fluke Corp. (USA)

Germany* United Kingdom

In den Engematten 14 52 Hurricane Way

79286 Glottertal Norwich, Norfolk

Germany NR6 6JB United Kingdom

Phone: +49 (0) 7684 8009 - 0 Phone: +44 (0) 1603 25 6662

beha-amprobe.de beha-amprobe.com

The Netherlands - Headquarters**

Science Park Eindhoven 5110

5692 EC Son

The Netherlands

Phone: +31 (0) 40 267 51 00

beha-amprobe.com

*(Correspondence only – no repair or replacement available from this

address. European customers please contact your distributor.)

**single contact address in EEA Fluke Europe BV

TMA10A Anemometer/Thermometer

Contents

USING THE PUSHBUTTONS..................................................... 2

DISPLAY INDICATORS.............................................................. 3

MAKING MEASUREMENTS ..................................................... 4

Air Velocity Measurements ................................................ 4

Air Flow Measurements ..................................................... 4

Single Point MIN/MAX/AVG Recording ............................. 5

Multi Point Average Recording ......................................... 5

Data Hold Feature .............................................................. 6

Changing the Units of Measure......................................... 6

AUTO POWER OFF .................................................................. 7

ERROR MESSAGE DISPLAY...................................................... 7

USEFUL EQUATIONS AND CONVERSIONS ............................. 7

Cubic Equations .................................................................. 7

Units Conversion Table....................................................... 7

REPLACING THE BATTERY....................................................... 7

SPECIFICATIONS....................................................................... 8

USING THE PUSHBUTTONS

VELOCITY

FREE AREA

VOLUMES

Please See Manual

For Operation

ON /OFF MODEHOLD

MIN MAX AVERAGE

SINGLE

POINT

MULTI-

POINT

ANEMOMETER THERMOMETER

Button Description

ON/OFF Turns the meter on and off.

MODE Toggle between velocity, free area, and volume.

HOLD Captures a reading. Sets digit to the desired value.

MIN MAX View the minimum or maximum. Average or record

value.

AVERAGE Display the average of all the measurements. Select

the next digit for editing.

DISPLAY INDICATORS

Vel Air velocity measurement.

FLOW Air flow/air volumen.

AREA Free area default setting.

Hold Freezes the reading.

knots 1850 meters per hour.

ft/m Feet per minute.

ft2 Square feet.

m/s Meters per second.

m2 Square meters.

mil/h Miles per hour.

cfm Cubic feet per minute.

km/h Kilometers per hour.

cms Cubic meters per second.

Primary display Numerical display for air velocity, air volume, and

free area digit.

°C Celsius units.

°F Fahrenheit units.

Secondary display Temperature display or record number.

MIN Minimum data.

MAX Maximum data.

REC Record and saved.

AVG Average data.

- Polarity indicator for negative temperature.

MAKING MEASUREMENTS

Air Velocity Measurements

Air velocity and temperature measurements can be displayed on this

meter in the following units of measure: ft/m (feet per minute) or m/s

(meters per second) for air velocity and °F or °C for temperature.

1. Connect the sensor to the sensor input jack on top of the meter.

2. Turn on the meter using the ON/OFF button.

3. The 'Vel' indicator should appear on the upper left on the LCD. If

not, press and hold the MODE button until a beep is heard. Repeat

this procedure until 'Vel' appears on the display.

4. Place the sensor in the air current to be measured.

5. View the air velocity and temperature readings on the LCD Display.

The upper display shows the air velocity reading. The lower display

shows the temperature.

Air Flow Measurements

In order to take air flow measurements, the area of the duct under test (in

ft2 or m2) must first be determined (check with the duct manufacturer if

necessary). Once the area is known, enter the value as follows:

1. Turn on the meter with the ON/OFF button.

2. Press and hold the MODE button until a beep is heard. “AREA”

appears on the display and one digit will be blinking indicating that

value can be changed.

3. Press the HOLD button to adjust the digit to the value needed.

4. Press the AVERAGE button to select the next digit for editing.

5. When the area is correctly entered, press the MIN MAX button

once. A beep will sound and the digits will stop blinking.

6. Press the HOLD button once to store the area value.

7. The meter is now ready to measure air flow. Place the sensor in the air

current and view the air flow and temperature readings on the LCD.

Otros manuales para TMA10A

Tabla de contenidos

Idiomas:

Otros manuales de Instrumento de medición de Amprobe

Amprobe

Amprobe TMA40-A Manual de usuario

Amprobe

Amprobe TH-1 Manual de usuario

Amprobe

Amprobe TH-1 Manual de usuario

Amprobe

Amprobe ACD-400 Manual de usuario

Amprobe

Amprobe VPC-10 Manual de usuario

Amprobe

Amprobe SOLAR-500 Manual de usuario

Amprobe

Amprobe TMA-20HW Manual de usuario

Amprobe

Amprobe AMB-45 Manual de usuario

Amprobe

Amprobe TMA-21HW Manual de usuario

Amprobe

Amprobe SM-10 Manual de usuario

Amprobe

Amprobe THWD-3 Manual de usuario

Amprobe

Amprobe WT-50 Manual de usuario

Amprobe

Amprobe MAN02-A Manual de usuario

Amprobe

Amprobe THWD-5 Manual de usuario

Amprobe

Amprobe TMD-10 Manual de usuario

Amprobe

Amprobe LM-120 Manual de usuario

Amprobe

Amprobe AT-6000 Manual de usuario

Amprobe

Amprobe AT-7020 Manual de usuario

Amprobe

Amprobe LM-100 Manual de usuario

Amprobe

Amprobe ACD-15 Pro Manual de usuario

Amprobe

Amprobe NCV-1020 Manual de usuario

Amprobe

Amprobe ACDC-3400 IND Manual de usuario

Amprobe

Amprobe MANO2-A Manual de usuario

Amprobe

Amprobe VPC-20 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario