Amprobe AM91RS Manual de usuario

USER'SUSER'S

MANUALMANUAL

AM91RS

AMPROBE

A United Dominion Company

1) SAFETY

This manual contains information and warnings that must be followed for operating the

meter safely and maintaining the meter in a safe operating condition. If the meter is used

in a manner not specified by the manufacturer, the protection provided by the meter may

be impaired. The meter is intended only for indoor use.

The meter meets the requirements for double insulation to IEC61010-1(1995), EN61010-

1(1995), UL3111-1(6.1994), CSA C22.2 NO. 1010-1-92 to terminals:

V/R : Category IV 600V ac and dc, and Category III 1000V dc and 750V ac.

mA/µA : Category III 500V ac, and Category II 300V dc.

A : Category III 600V ac, and Category II 300V dc.

PER IEC61010 OVERVOLTAGE INSTALLATION CATEGORY

OVERVOLTAGE CATEGORY I

Equipment of OVERVOLTAGE CATEGORY I is equipment for connection to circuits in

which measures are taken to limit the transient overvoltages to an appropriate low level.

Note – Examples include protected electronic circuits.

OVERVOLTAGE CATEGORY II

Equipment of OVERVOLTAGE CATEGORY II is energy-consuming equipment to be

supplied from the fixed installation.

Note – Examples include household, office, and laboratory appliances.

OVERVOLTAGE CATEGORY III

Equipment of OVERVOLTAGE CATEGORY III is equipment in fixed installations.

Note – Examples include switches in the fixed installation and some equipment for

industrial use with permanent connection to the fixed installation.

OVERVOLTAGE CATEGORY IV

Equipment of OVERVOLTAGE CATEGORY IV is for use at the origin of the installation.

Note – Examples include electricity meters and primary over-current protection

equipment.

TERMS IN THIS MANUAL

WARNING identifies conditions and actions that could result in serious injury or even

death to the user.

CAUTION identifies conditions and actions that could cause damage or malfunction in

the instrument.

WARNING

To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.

To avoid electrical shock hazard, observe the proper safety precautions when working

with voltages above 60 VDC or 30 VAC rms. These voltage levels pose a potential shock

hazard to the user. Do not touch test lead tips or the circuit being tested while power is

applied to the circuit being measured. Keep your fingers behind the finger guards of the

test leads during measurement. Inspect test leads, connectors, and probes for damaged

insulation or exposed metal before using the instrument. If any defects are found, replace

them immediately. Do not measure any circuit that draws more than the current rating of

the protection fuse. Do not attempt a current measurement where the open circuit voltage

is above the protection fuse voltage rating. Suspected open circuit voltage can be

checked with voltage functions. Never attempt a voltage measurement with the test lead

inserted into the µA/mA or A input jack. Only replace the blown fuse with the proper

rating as specified in this manual.

CAUTION

Disconnect the test leads from the test points before changing functions. Always set the

instrument to the highest range and work downward for an unknown value if you are

using manual ranging mode.

INTERNATIONAL ELECTRICAL SYMBOLS

!! Caution ! Refer to the explanation in this Manual

Caution ! Risk of electric shock

Earth (Ground)

Double Insulation or Reinforced insulation

Fuse

2) ELECTROMAGNETIC COMPATIBILITY (EMC)

The instrument meets EN55022(1994/A1; 1995/Class B) and EN50082-1(1992)

3) PRODUCT DESCRIPTION

Panel Illustration

1) 4-3/4 digits 40000 counts LCD

display

2) Push-buttons for special

functions & features

3) Selector to turn the Power On

or Off and Select a function

4) Input Jack for 10A (20A for

30sec) current function

5) Input Jack for all functions

EXCEPT current (µA, mA, A)

functions

6) Common (Ground reference)

Input Jack for all functions

7) Input Jack for milli-amp and

micro-amp current functions

Analog bar-graph

The analog bar graph provides a visual indication of measurement like a traditional analog

meter needle. It is excellent in detecting faulty contacts, identifying potentiometer clicks,

and indicating signal spikes during adjustments.

DC+AC True RMS

DC+AC True RMS is a term which identifies a DMM that responds accurately to the

total effective RMS value regardless of the waveforms such as: square, sawtooth,

triangle, pulse trains, spikes, as well as distorted waveforms with the presence of

harmonics and DC components. Harmonics and DC components may cause :

1)Overheated transformers, generators and motors to burn out faster than normal

2)Circuit breakers to trip prematurely

3)Fuses to blow

4)Neutrals to overheat due to the triplen harmonics present on the neutral

5)Bus bars and electrical panels to vibrate

Crest Factor

Crest Factor is the ratio of the Crest (instantaneous peak) value to the True RMS value,

and is commonly used to define the dynamic range of a True RMS DMM. A pure

sinusoidal waveform has a Crest Factor of 1.4. A badly distorted sinusoidal waveform

normally has a much higher Crest Factor.

NMRR (Normal Mode Rejection Ratio)

NMRR is the DMM's ability to reject unwanted AC noise effect which can cause

inaccurate DC measurements. NMRR is typically specified in terms of dB (decibel). This

product has a NMRR specification of 60dB at 50 and 60Hz, which means a good

ability to reject the effect of AC noise in DC measurements.

CMRR (Common Mode Rejection Ratio)

Common mode voltage is voltage present on both the COM and VOLTAGE input

terminals of a DMM, with respect to ground. CMRR is the DMM's ability to reject

common mode voltage effect which can cause digit rattle or offset in voltage

measurements. This series has a CMRR specifications of 60dB at DC to 60Hz in

ACV function; and 120dB at DC, 50 and 60Hz in DCV function. If neither NMRR nor

CMRR specification is specified, a DMM's performance will be uncertain.

4) OPERATION

ACV, ACV + Hz, & dBm + Hz functions

Defaults at ACV. Press SELECT button momentarily to select ACV + Hz. Press

SELECT button momentarily again to select dBm + Hz. Input sensitivity for Hz varies

automatically with voltage range selected in ACV + Hz function. It is designed especially

for measuring the frequency of high voltage noisy electrical signals.

Note: Default Reference impedance 600Ωwill be displayed for 2 seconds before

displaying the dBm + Hz readings. Press dBm-ΩΩ (RANGE) button momentary to select

different reference impedance from 4, 8, 16, 32, 50, 75, 93, 110, 125, 135, 150, 200, 250,

300, 500, 600, 800, 900, 1000, up to 1200Ω. Impedance values will again be displayed for

2 seconds before displaying the dBm + Hz readings.

DCV, DC + AC V functions

Defaults at DC. Press SELECT button momentarily to select DC + AC. Analog bar-

graph will be disabled in the DC + AC mode.

Hold

The hold function freezes the display for later view. Press the HOLD button momentarily

to activate and to exit the hold function

DC, AC, AC + Hz mV functions

Defaults at DC. Press SELECT button momentarily to select AC. Press SELECT button

momentarily again to select AC + Hz.

DC, AC, AC + Hz Adapter functions

The operation of Adapter function is similar to the mV function. Defaults at DC. Press

SELECT button momentarily to select AC. Press SELECT button momentarily again to

select AC + Hz. Adapter function is of extra high input impedance up to 1000MΩ, and

there is no decimal point on the digital display. It can cope with most voltage output

sensors/ transducers with the highest sensitivity and the least current drain.

Hz, % + Hz functions

Defaults at Hz. Press SELECT button momentarily to select % + Hz.

Note: Unlike the AC + Hz function, this high resolution Hz function is set at the highest

input sensitivity to measure digital type electronic signals.

Backlighted display

Press the SELECT button for 1 second or more to turn on and off the display backlight

function. The backlight will also be turned off automatically after 42 seconds to extend

battery life.

Tabla de contenidos

Otros manuales de Instrumento de medición de Amprobe

Amprobe

Amprobe AMP-25 Manual de usuario

Amprobe

Amprobe AM-33 Manual de usuario

Amprobe

Amprobe LH41 Manual de usuario

Amprobe

Amprobe MAN15 Manual de usuario

Amprobe

Amprobe ACD - 50NAV Manual de usuario

Amprobe

Amprobe AC50A Manual de usuario

Amprobe

Amprobe TMA40 Manual de usuario

Amprobe

Amprobe ECB50A Manual de usuario

Amprobe

Amprobe WT-40 Manual de usuario

Amprobe

Amprobe SOLAR-500 Manual de usuario

Amprobe

Amprobe THWD-10 Manual de usuario

Amprobe

Amprobe WT-50 Manual de usuario

Amprobe

Amprobe BT-AFT1 Manual de usuario

Amprobe

Amprobe AD40B Manual de usuario

Amprobe

Amprobe CO2-100 Manual de usuario

Amprobe

Amprobe FS-3 Manual de usuario

Amprobe

Amprobe WT-70 Manual de usuario

Amprobe

Amprobe AT-7020 Manual de usuario

Amprobe

Amprobe 3730217 Manual de usuario

Amprobe

Amprobe SM70 Manual de usuario

Amprobe

Amprobe THWD-3 Manual de usuario

Amprobe

Amprobe SOLAR-600 Manual de usuario

Amprobe

Amprobe TH-1 Manual de usuario

Amprobe

Amprobe NCV-1020 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario