AMIC A9280-A-000 Manual de usuario
AMIC A9280-A-000
13.56MHz Compact Flash
RFID Reader
User Manual
Rev 1.0
© AMIC 2004
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in
any form or by any means, electronic or mechanical, including photocopying and microfilm, without
permission in writing from AMIC.
AMIC Communication Co.
No.2, Li-Hsin 6th Road, SBIP, 300 Hsinchu, Taiwan, R.O.C
TEL: 886-3-5679966
FAX: 886-3-5679977
© AMIC Dec. 2004 – All rights reserved
Trademarks:
Philips, and I•Code SLI are registered trademarks of Philips Semiconductor.
TI, and Tag-It HF-I are registered trademarks of Texas Instruments.
HP and IPAQ are registered trademarks of Hewlett-Parker.
All other trademarks mentioned herein are properties of their respective companies.
© AMIC Dec. 2004 – All rights reserved
AMIC A9280-A-000 User Guide
1. Introduction
Thank you for purchasing AMIC A9280-A-000 Compact Flash RFID Reader.
AMIC’s A9280-A-000 is a user-friendly RFID operating at 13.56MHz frequency range.
This RFID reader is to be used with PDA or handheld devices equipped with
Compact Flash Type-1 or Type-2 slot. AMIC’s A9280-A-000 is a Compact Flash
RFID reader is compliant with the international recognized ISO-15693 standard. It
has built-in antenna for easy of use, and it is capable of 200mW RF power output.
AMIC’s A9280-A-000 CF RFID reader supports Microsoft Pocket PC 2003
(WinCE.NET4.2) operation system.
2. Product Contents
Before starting using the A9280-A-000 compact flash RFID reader, please check that
the package contains the following items:
− One AMIC A9280-A-000 CF RFID reader unit.
− One CD-ROM containing device driver, user manual, and GUI utility.
− Three ISO-15693 standard RFID ISO cards (RFID tags).
© AMIC Dec. 2004 – All rights reserved p1 of 20 Rev 1.0
AMIC A9280-A-000 User Guide
2.1.Installation Requirements
AMIC A9280-A-000 requires the following minimum system environment for proper PDA
device driver installation and reader operation:
Minimum System Requirement:
PDA
− Processor: Intel XScale ARM processor running at 400MHz or faster
− Memory: Minimum 2MB SDRAM
− PC interface: USB (supported via PDA cradle interface)
− One Type-I or Type-II Compact Flash slot
− PC synchronization utility software that was included with PDA
− Operation systems:
Microsoft Pocket PC 2003 (WinCE.NET 4.2) or
Microsoft Windows Mobile 2003 Second Edition Software for Pocket
PC
(WinCE.NET 4.2.1)
PC
− Processor: Pentium 133MHz or faster
− Memory: 32MB RAM
− Interface: One USB1.1 compliant port
− Hard Disk Space: 10MB of free disk space
− PDA synchronization utility installed (provided by PDA manufacturer)
− Operation system:
Windows 2000
Windows XP
© AMIC Dec. 2004 – All rights reserved p2 of 20 Rev 1.0
AMIC A9280-A-000 User Guide
3. Setup Your PC
Before installing AMIC 9280-A-000 device driver onto your PDA, make sure that the PC
used to connect to your PDA has the appropriate synchronization software installed.
PDA’s synchronization software will enable user to install the necessary device driver
and GUI utility for AMIC 9280-A-000 CF on to your PDA. For example, Microsoft’s
Active Sync should be used with PDA running Microsoft Pocket PC 2003 (WinCE.NET
4.2) or Microsoft Windows Mobile 2003 Second Edition Software for Pocket PC. Please
refer to your PDA’s operational manual for the actual synchronization software designed
for your PDA and respective details.
© AMIC Dec. 2004 – All rights reserved p3 of 20 Rev 1.0
AMIC A9280-A-000 User Guide
4. Install A9280-A-000 Pocket PC Device Driver
To install A9280-A-000 Pocket PC device driver on your PDA, please follow the following
procedures:
1. Make sure that the required PDA synchronization software has been installed
on your PC.
2. Turn on your PC and wait for it to boot up completely.
3. Connect your PDA to your PC through PDA manufacturer recommended
method. (either through cradle, USB cable, or etc)
4. Establish communication between your PC and your PDA.
5. Put the device driver / GUI utility CD in your PC’s CD-ROM drive.
6. Use Windows Explorer to go to the Drivers & Utility directory on the CD-ROM.
7. Double click on elserialsetup_pocketpc.exe.
8. The Pocket PC installation screen will pop up as in the figure – 1.
Figure - 1
9. Click on Next button
© AMIC Dec. 2004 – All rights reserved p4 of 20 Rev 1.0
AMIC A9280-A-000 User Guide
10. The License Agreement screen will be displayed as in Figure - 2
Figure - 2
11. Select “I accept the terms in the license agreement”
12. Click on the Finish button
The A9280-A-000 Pocket PC device driver is now installed on your PDA.
For detail operating instructions on how to establish communication link between PC and
PDA, please refer to PDA manufacturer’s operating manual.
© AMIC Dec. 2004 – All rights reserved p5 of 20 Rev 1.0
AMIC A9280-A-000 User Guide
5. Install AMIC A9280-A-000 GUI Utility on PDA
1. Make sure that the required PDA synchronization software has been installed
on your PC.
2. Turn on your PC and wait for it to boot up completely.
3. Connect your PDA to your PC through PDA manufacturer recommended
method. (either through cradle, USB cable, or etc)
4. Establish communication between your PC and your PDA.
5. Put the device driver / GUI utility CD in your PC’s CD-ROM drive.
6. Use Window’s Explorer on PC to go to the Demo Software directory on the
CD-ROM.
7. Copy Rfid15693Demo.exe from the Demo Software directory on the CD-ROM
to the Mobile Device directory.
8. After Rfid15693Demo.exe is copied from PC to the PDA, you should be able to
see the file, Rfid15693Demo.exe, listed on PDA’s File Explorer.
Figure – 3
© AMIC Dec. 2004 – All rights reserved p6 of 20 Rev 1.0
AMIC A9280-A-000 User Guide
6. AMIC A9280-A-000 GUI Utility Software
Introduction
The GUI Utility software is a user-friendly graphical-user-interface which enables its
users to have full access to their RFID tags. These functionalities include reading data
from tags, accessing specific memory location within tags’ memory space, and writing
data on to the tag. For detail tag memory structure, please see respective tag
manufacturer’s datasheet.
2 3
1
4
5
13
6
14
7
15
8
16 9
17 10
18 11
12
19
Figure - 4
1. COM Port Setting
2. Status Dialog Box
3. OK button
4. Close Program button
5. Block Number
6. Open Reader button
7. Block data
8. Exit button
9. Clear button
10. Auto Scan Counter
11. Auto Scan Status
12. Auto Off button
13. Read Card UID button
14. Read Data button
15. Write Data button
16. Auto Scan button
17. CARD UID Read history window
18. Response Information window
19. Operation OK / Fail Display
© AMIC Dec. 2004 – All rights reserved p7 of 20 Rev 1.0
AMIC A9280-A-000 User Guide
Launch the GUI Utility on PDA
1. Make sure that the AMIC A9280-A-000 RFID CF reader is inserted into PDA’s
CF slot securely
2. “New Hardware Found” window will be displayed as in figure – 5
3. Use PDA’s stylus and single tap on “OK” button
4. Use PDA’s File Explorer to list application files available
5. Use PDA’s stylus and single tap on Rfid15693Demo.exe
6. The following screen should be displayed
Figure - 5
7. AMIC A9280-A-000 RFID CF reader needs to be opened before any reader
functionality can be made available to its user. This can be done by single tap
on the “OPEN” button.
8. After applying single tap to the “OPEN” button, if the specified COM port is
initialized successfully, “Init OK” will be displayed to the box to the right of COM
port setting. At this time, the AM9280-A-000 CF reader is ready for user
access.
© AMIC Dec. 2004 – All rights reserved p8 of 20 Rev 1.0
Tabla de contenidos
