Amibot Everybot Swip AS50 Manual de usuario
EN
Floor cleaning robot
User Manual
AS50
EN
User Manual
Thank you for choosing AMIBOT! We hope you are fully satised
using your robot as part of your cleaning routine.
If you should encounter situations that have not been properly
addressed in this User Manual or were to have any queries, do not
hesitate to contact us and a member of our Technical Customer
Service Department will be more than happy to answer your
questions.
For more information, you can visit the ocial AMIBOT website:
www.amibot.tech
We reserve the right to make technical alterations to the appliance
without prior notice with the objective of continually improving our
products and customer satisfaction.
Please carefully read all instructions in this manual before using this
appliance. AMIBOT will not be liable for damage due to incorrect use.
1
Contents
EN
Recommendations ............................................................. 2
Product overview................................................................ 3
Product contents..................................................................................... 3
Product diagram ..................................................................................... 4
Operating the robot........................................................... 6
Charging the robot ................................................................................. 6
Cleaning ................................................................................................... 7
Starting the robot ................................................................................... 8
Cleaning routes................................................................................10
Putting the robot in standby ............................................................... 13
Stopping the robot................................................................................ 13
Maintenance...................................................................... 14
Water tanks............................................................................................ 14
Gap sensors........................................................................................... 14
Obstacle sensors and light sensor...................................................... 15
Thick microbre cleaning pads ........................................................... 15
Indicator lights and sounds............................................16
Troubleshooting................................................................17
Table: Malfunctions and possible causes .......................................... 17
Warranty and after-sales service.................................. 19
Technical specications ..................................................20
Safety instructions and precautions............................21
Operating conditions............................................................................ 21
Recycling instructions .....................................................23
2
Recommendations
EN
• AMIBOT Swip is designed to be used inside.
• AMIBOT Swip is designed for routine oor cleaning. It is not in-
tended to replace heavy-duty cleaning.
• AMIBOT Swip needs a headway of at least 12 cm so that it can go
under furniture.
• AMIBOT Swip cannot go over obstacles, such as thresholds, oth-
erwise it automatically stops or reverses.
• AMIBOT Swip is designed to clean hard oors only.
• AMIBOT Swip must be used on at surfaces or slopes of no more
than 10%.
• Remove all objects located on the oor before starting the clean-
ing cycle.
• If the robot could come across a gap while cleaning, please check
that the gap sensors are clean.
• AMIBOT Swip is not designed to clean water or other liquids.
• Do not use the appliance on damp oors.
• Please switch o the appliance before handling it (manually mov-
ing it, maintenance, cleaning).
• The remote control requires 2 x LR03-type batteries (AAA), which
are included.
3
Product overview
EN
Product contents
1
4
1. AMIBOT Swip robot
2. Power adapter
3. 2 x water tanks
4. 4 x thick microbre cleaning
pads
5. Remote control (batteries
included)
6. User manual
2 3
5 6
4
Product overview
EN
Product diagram
Robot top view
1. Start/Stop button
2. Carry handle
3. Bumper
4. Light sensor
5. Obstacle sensors
6. Power plug
Robot bottom view
1. Gap sensors
2. Water tank compartment
3. Power button
1
2
3
5
4
6
1
2 3
Water tanks
1. Notches to attach the water
tanks to the robot
2. Rell nozzle
3. Velcros to attach thick
microbre cleaning pads
4. Drip nozzles
1 2 3 4
5
Product overview
EN
Remote control
1. Directional arrows
2. Start/Stop button
3. Y Mode button
4. DRY Mode button
5. Wall Mode button
6. SPOT Mode button
7. TURBO Mode button
1
2
3
4
5
6
7
6
Operating the robot
EN
Charging the robot
Plug the robot in using the power adapter provided. The Start/Stop
buttons on the appliance and the remote control do not work when
the robot is charging.
NOTES:
• Before using the robot for the rst time, you are recommended to fully charge
the battery (for 150 minutes).
• You do not need to switch the robot on while it is charging.
• The average charge time is around 100 minutes. When the robot's battery is
fully empty, the charge time can be up to 150 minutes.
• Unplug the robot before starting it.
• If the robot is not used for a long period of time, you are recommended to fully
charge the battery, switch o the robot and store it in a cool, dry place.
7
Operating the robot
EN
NOTES:
• Each water tank has a maximum capacity of 60ml.
• For optimum cleaning, check the dilution ratio indicated on the detergent bottle.
• Only use oor cleaner.
Cleaning
Attaching the cleaning pads
NOTE: If the microbre cleaning pads are too damp, the robot may not work
correctly. Wring them out well before attaching them to the underside of the robot.
Preparing the water tanks
Open the water tanks' rell
nozzle in the direction of the
arrow on the cap. Carefully pour
clean water with oor cleaner
into the tanks. Close the tanks.
Dampen the thick microbre
cleaning pads with clean water,
then wring them out. Attach
them to the water tanks using the
Velcros. Make sure the cleaning
pads are correctly positioned in
the centre of the water tanks.
8
Operating the robot
EN
Inserting the water tanks
Insert the two water tanks into the compartments on the underside
of the robot. Once inserted, the water tanks must be able to rotate
freely. The robot is ready to start its cleaning cycle.
NOTES:
• Check that the water tanks are attached to the robot correctly. For optimum
performance, never cover the edge detectors.
• Do not use the robot on rugs or carpets.
• The water tanks must be removed from the robot before it is charged.
Starting the robot
Once the water tanks are inserted,
switch the robot on using the
power button on the underside
of the appliance (Figure 1). The
robot beeps several times and
the Start/Stop button turns blue.
Turn the robot over and place it
on the oor.
Figure 1
Tabla de contenidos
Idiomas:
Manuales populares de Robótica de otras marcas
STEMCenter USA
STEMCenter USA Pi-Bot v2.00 Manual de usuario
SunFounder
SunFounder PiDog Manual de usuario
Universal Robots
Universal Robots UR5 Manual de usuario
Universal Robots
Universal Robots E Series Manual de usuario
YASKAWA
YASKAWA MOTOMAN-MPL80 II Manual de usuario
EFORT
EFORT ECR5 Manual de instrucciones
