AMI Kit-CJE B75B Manual de usuario

Page 1 of 5

22166958

REV. A

Kit-CJE Core Upgrade B75B Motherboard

Kit #22166908

This kit contains the parts and instruction to install the B75B Motherboard into your CJE

Computer Core. Notice: This kit does not provide support for Modem dialup connections.

Tools Required

#2 Phillips Screwdriver, ¼ Nut Driver.

Parts Included with this Kit

Item # Part Number Description Quantity

1 40924220 B75B Motherboard 1

2 22350001 Hard Drive SSD Win10 (US) 1

3 34052405 CBA – Power On/Reset 1

4 22132269 Cable Assembly COM To I/O 1

5 22132270 Cable Assembly Power On/Reset 1

6 22157606 License – Windows 10 1

7 22167738 Label – (61197014) 1

8 22188403 Card – Trigger Code (Not Shown) 1

These Instructions

Figure 1

Installation Instructions

Page 2 of 5

22166958

REV. A

Removal Instructions

Caution: When installing this B75B motherboard, care should be taken to avoid static discharges

which could damage the motherboard. The motherboard installation should be done on a static

dissipative mat along with a grounding wrist strap. Retain all the screws while installing this kit.

1. Turn the jukebox power off and unplug the power cord from the wall outlet.

2. Open the jukebox door and disconnect all the harnessing to the computer core. Note where the

cables plug into the Computer Core Assembly for later reinstallation. Remove the Computer

Core from the jukebox.

3. Remove all necessary covers to access the motherboard. Unplug and remove all of the ATX power

supply and I/O board connections from the motherboard. Remove the Power and SATA DATA cable

from the hard drive. Remove the modem card and its PCI cover from the motherboard if present. It

will not be reused. Remove the three screws securing the power supply to the computer core chassis.

Carefully rotate the power supply out of the computer core chassis as shown in Figure 2.

4. Remove the POWER ON/OFF reset board and its ribbon cable connected to the motherboard they

will no longer be used.

5. Remove the Ribbon cable connected to the I/O and motherboard it also will not be reused.

6. Remove the four screws that secure the motherboard to the core chassis. The motherboard and the

front I/O panel will not be reused.

Figure 2

Power Supply

Power ON/OFF

Reset board

Motherboard

Page 3 of 5

22166958

REV. A

Installation Instructions

7. Insert the motherboard I/O shield into position and carefully align the new B75B motherboard (Item

#1) to the four existing studs of the computer core chassis. Secure the motherboard with four screws

removed in step #6.

8. Connect the POWER ON/RESET cable 22132270 (Item #5) into the keyed 10 pin header of the

POWER ON/RESET circuit board assembly 34052405 (Item #3) and reinstall into your computer

Core using the same two screws. Connect the other end of the cable to the “F Panel” header of the

B75B Motherboard. See Figure 3.

9. Connect the COM TO I/O Cable Assembly 22132269 (Item #4) to the keyed 10 pin header of the I/O

board still mounted in the computer core chassis. Connect the other end of the cable to the “COM 1”

header of the B75B motherboard. See Figure 3.

10. Connect the computer core chassis fan harness to the “SYS FAN” header of the B75B motherboard.

Figure 3

COM TO I/O

Cable

POWER ON/RESET

Board and connected

22132269 cable.

“F-Panel” header

“SYS FAN”

Header I/O Board

I/O Shield

Chassis Fan

Page 4 of 5

22166958

REV. A

11. Carefully rotate the ATX Power Supply back into position and secure with three screws previously

removed in step #3. Reconnect the ATX 20 pin, and 4-pin power connections to the B75B

motherboard. Reconnect the 4-pin power connection to the I/O board. See Figure 4.

12. Install the new 22350001 Hard Drive (Item #2) into the holder and connect the SATA power and the

SATA DATA cables to the B75B Motherboard as shown in Figure 4.

13. Reattach the covers and apply the new core computer part number label (Item #7) over the top of the

original core computer part number.

14. Reinstall the modified Computer Core into the jukebox. Reconnect all cables removed in step #2.

Take a moment to visually inspect the jukebox to ensure proper connections before powering up the

jukebox.

15. Attach the Windows 10 License (Item #6) label to the jukebox cabinet somewhere near, or over the

top of the original Windows license label.

Figure 4

SATA DATA

Cable

I/O Board power

connection

4 pin power

connection

Hard Drive power

connection

20 pin power

connection

Hard Drive

Page 5 of 5

22166958

REV. A

Power up Testing

1. Plug the jukebox back into the wall then power up the jukebox and ensure the jukebox UI comes up.

This will take some time and may include one or more reboots.

2. In order for the jukebox to connect to the AMI network, the MAC address of the computer core must

be entered into the AMI database. This will require a phone call to the AMI Tech Support line, 1-877-

ROC-N-ROL (1-877-762-6765).

a. The MAC address is found on a Service Mode screen.

b. If the jukebox is not in the Service Mode, push the Service button on the core computer.

c. Push the Calibrate button on the core computer and calibrate the touch screen.

d. Touch Diagnostics then touch System Information. The MAC address will be displayed in the third

block down from the top right.

e. To help the AMI Tech Support technician configure your jukebox in the AMI system, please have

the jukebox model and serial number along with the MAC address when you call. Inform the

technician you are installing the new motherboard upgrade kit.

3. After Tech Support has entered the MAC address of the jukebox, you will need to enter the Trigger

Code for the hard drive.

a. From the main menu in the Service Mode, touch System Setup then touch Enable/Extend

Features.

b. Using the on-screen keyboard, enter the trigger code found on the Trigger Code Card (Item #8)

then touch the Send Code button.

AMI Entertainment Network LL – 4147 Eastern Ave SE – Grand Rapids, MI 49508

Tabla de contenidos

Otros manuales de Placa madre de AMI

AMI

AMI EMB-B75B Manual de usuario

AMI

AMI MI890 Manual de usuario

AMI

AMI MB941 Manual de usuario

AMI

AMI ATX-H310A Manual de usuario

AMI

AMI IMBM-Q87A Manual de usuario

AMI

AMI MB960 Manual de usuario

AMI

AMI Mark IV Screamer Manual de usuario

AMI

AMI Ecast View B75B Manual de usuario

AMI

AMI MI956 Manual de usuario

AMI

AMI MI946F Manual de usuario

AMI

AMI MI982 Manual de usuario

AMI

AMI EMB-Q87A Manual de usuario

AMI

AMI M920 Series Manual de usuario

AMI

AMI MI987 Manual de usuario

AMI

AMI 410 Manual

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario