American Time SQA461RSxE Manual de usuario

Installation and Operation Manual

Part # H004789

Rev. 1

June 2014

Wireless Digital Clock/Elapsed

Time Indicator

with Code Blue

SQA461RSxE Owner's Manual

Electrical Shock Hazard

WARNING: Hazardous voltage in electrical equipment can cause severe personal injury or death. Inspection,

installation, and preventive maintenance should only be performed on equipment to which power has been turned

off, disconnected and electrically isolated so no accidental contact can be made with energized parts.

Electrostatic Sensitive Devices

CAUTION: This equipment contains electronic devices that are sensitive to static electric charges. To guarantee

protection for the circuitry of this unit, it is required that electrostatic handling precautions be observed

when installing or repairing this equipment. Any technician or other personnel working on this unit must

wear a static grounding wrist strap or similar device to provide protection of sensitive components.

ATTENTION

OBSERVE PRECAUTIONS

FOR HANDLING

ELECTROSTATIC

SENSITIVE

DEVICES

SQA461RSxE Owner's Manual Table of Contents

American Time

140 3rd Street South

PO Box 707

Dassel, MN 55325-0707

Phone: 800-328-8996

Fax: 800-789-1882

atsclock.com

Important Installation and Warranty Information ....................................................................................................4

Specications ............................................................................................................................................................5

Description.................................................................................................................................................................6

SQA461RSxE Digital Clock/Timer ....................................................................................................................6

ATSTCS Control Station ...................................................................................................................................7

Installation Instructions ...........................................................................................................................................8

SQA461RSxE Installation Instructions................................................................................................................8

ATSTCS Installation Instructions ........................................................................................................................9

Operation ................................................................................................................................................................10

Power Up .......................................................................................................................................................10

Setting Time ..................................................................................................................................................10

Setting the Up Counter Preset Time ................................................................................................................10

Up Counter Elapsed Time Operation................................................................................................................11

Setting the Down Counter Preset Time ...........................................................................................................11

Down Counter Elapsed Time Operation...........................................................................................................11

Code Blue.................................................................................................................................................................12

Operation .......................................................................................................................................................12

Wiring ............................................................................................................................................................12

Important Considerations ...............................................................................................................................13

Maintenance ............................................................................................................................................................14

Appendix 1: Operators Flowchart.............................................................................................................................15

SQA461RSxE Owner's Manual

IMPORTANT INSTALLATION AND WARRANTY INFORMATION

WARRANTY INFORMATION: American Time (the Manufacturer) provides a limited warranty to the Original Purchaser of this

product. The Original Purchaser is the party to whom the Manufacturer issued its Sales Order, generally the Manufacturer’s

distributor. In order to preserve this warranty, it is important that only persons who have been properly trained and authorized by

the Manufacturer service the product.

Other parties involved in the installation of this product may have also provided a warranty, which may be different than that of the

Manufacturer. The Manufacturer will only be responsible to the Original Purchaser and only for the

Manufacturer’s own warranty. For further information regarding the Manufacturer’s warranty, contact the Original

Purchaser.

OWNER’S MANUAL: The owner’s manual does not purport to cover all the details or variations in the equipment described,

nor does it provide for every possible contingency to be met in connection with installation, operation and maintenance. All

specications subject to change without notice. Should further information be desired or should particular problems arise which

are not covered sufciently, the matter should be referred to the Installer or Original Purchaser listed below.

INSTALLER INFORMATION

COMPANY: INSTALLER: PHONE:

ADDRESS: CITY: STATE: ZIP:

DATE INSTALLED: INSTALLER’S SIGNATURE:

ORIGINAL PURCHASER INFORMATION

COMPANY: PHONE:

ADDRESS: CITY: STATE: ZIP:

PURCHASER’S PURCHASE ORDER NO:

DATE PURCHASED:

ATS SALES ORDER ACKNOWLEDGMENT NO.:

ORIGINAL PURCHASER’S SIGNATURE:

NOTE: A copy of the above-completed information may be required by the Manufacturer for authorization of Warranty services.

SQA461RSxE Owner's Manual Specications

GENERAL

Weight: ..............................Digital Clock/Timer ............................... 8.80 lb.

...............................ATSTCS Control Station ........................... 0.27 lb.

External Dimensions:.........Digital Clock/Timer ............................... 6.1"h x 24"w x 3.5"deep

...............................ATSTCS Control Station ........................... 4.63"h X 4.56"w X 1.25"deep

SPECIFICATIONS

ELECTRICAL

Power Requirements (Digital Clock/Timer only):

Line Voltage: ..................................................................................... 120vac 50/60Hz -SQA461RSAE and SQA461RSPE

24vac 50/60Hz - SQA461RSBE

220vac 50/60Hz - SQA461RSKE

Note: Voltage is set at factory. See above part number sufx for reference.

Battery:............................................................................................... 9vdc Rechargeable Ni-Cad Battery

Battery Charger: ................................................................................ 9vdc Direct Current source with

current limiting resistor.

Maximum Current (Digital Clock/Timer only): .................................... 120vac - 130mA (max), 101mA (avg)

Memory Retention on Loss of Line Voltage: ..................................... 4 hours with fully charged battery

Distance of ATSTCS from Digital Clock/Timer:................................. 30-ft maximum with 22 AWG stranded wire

............................................................................................... with minimum 1/32" thick insulation

Clock Circuits: ................................................................................... 3.0mA. max. @ 24vac/120vac

Code Blue Circuits: ............................................................................ 3.0mA. max. @ 12vac/vdc-30vac/vdc

ENVIRONMENTAL

Ambient Operating Range: ................................................................ 10°C to 49°C (50°F to 120°F)

Recommended Storage Temperature: .............................................. -30°C to 45°C (-22°F to 113°F)

............................................................................................... for six months maximum

Humidity:............................................................................................ 85 %RH at 30°C (86°F)

OPERATION

Modes Available:................12 hour or 24-hour wireless synchronized

Incrementing timer with programmable preset value and start/stop capability

Decrementing timer with programmable preset value and start/stop capability

Code Blue incrementing timer

Accuracy: .............................................................................±1 second to SiteSync IQ system controller

Indications: ........................Digital Clock/Timer .....................hours and minutes - 4", bright red, seven segment LED’s

hours and minutes are separated by a colon

seconds - 2", bright red, seven segment LED’s

...............................ATSTCS Control Station ..............2 second audible alarm

Reception: ............................................................................Colons flash

SQA461RSxE Owner's Manual

Appendix Maintenance

Code Blue

Operation Installation Description

Clock/Timer Description

START/STOP RESET

INCREMENT ENTER

RUN

SET

DOWN

CLOCK

4 9/16”

4 1/2”

Control Station

”

6.1”

3.5”

ATSTCS Control Station

The SQA461RSxE is a six-digit digital multi-function synchronized clock/timer which can be used as an up or down

counting elapsed timer with an optional Code Blue trigger. The elapsed timers can be started, stopped, resumed, and reset.

Both timer modes have a programmable preset value. When the timer reaches the preset value, a two-second audible alarm

sounds from the ATSTCS control panel. The Code Blue up counting elapsed timer will override all other modes of operation

if used. The SQA461RSxE can function as a 12-hour or 24 hour clock which is synchronized by the SiteSync IQ wireless

clock system.

Digital Clock/Timer

SQA461RSxE Owner's Manual

AppendixMaintenance

Code Blue

OperationInstallationDescription

Control Station Switch Functions

START/STOP RESET

INCREMENT ENTER

RUN

SET

DOWN

CLOCK

RESET

ENTER

RUN

SET

DOWN

CLOCK

START/STOP

INCREMENT

Run/Set Switch -

Set Position: This position is used to set a preset up or down counting time (Timer). It is also used

to reset the Code Blue timer.

This position is not used for setting time. The controller will allow you to enter in a

12/24 hour mode and set a time. However, the time will be controlled and updated by

the SiteSync IQ system controller.

Run Position: This position is used to permit Clock/Timer to operate.

Up/Clock/Down Switch -

Up Position: This position is used to choose up counting elapsed timer mode.

Clock Position: This position is used to choose clock mode.

Down Position: This position is used to choose down counting elapsed timer mode.

Start/Stop/Increment Switch -

This button is used to start, stop, and resume timer count, when Run/Set Switch is in the Run

position (Code Blue timer can only be stopped).

This button is also used to increment/advance the number value being set when the Run/Set Switch

is in Set position.

Reset/Enter Switch -

This button is used to return a timer (excluding the Code Blue timer) to the beginning of its count, when

the Run/Set Switch is in Run position.

This button can also be used to select a eld (i.e. format, minute digits, hour digits) when the Run/

Set Switch is in Set position.

SQA461RSxE Owner's Manual

Appendix Maintenance

Code Blue

Operation Installation Description

Clock/Timer Installation

The Digital Clock/Timer can be mounted to a single or double gang box. To install the Digital Clock/Timer, follow the

instructions below. Ensure that installation conforms to the National Electrical Code and local wiring codes.

CAUTION: Electric Shock Hazard! Ensure that NO electrical power is present on any wire before installation.

uRemove the 6-32 black screw on the top of the clock which secures the back mounting plate. Mount the back plate to

a single or double gang box. See Figure 2 on page 9.

vMake electrical connections (hot, neutral, ground) to non-switched electrical circuit wiring using UL approved wire

nuts. Route eld wiring away from sharp projections, corners and internal components. For Molex, connect white to

neutral/common, black to positive/hot, green to ground and red to optional correction line if using a wired master.

Note: Voltage is set at the factory. See part number sufx reference.

120vac 50/60 Hz (SQA461RSAE and SQA461RSPE)

24vac 50/60 Hz (SQA461RSBE)

220vac 50/60Hz (SQA461RSKE)

wPull the ten wires from the clock to the control station. Keep these ten wires separate from the high voltage wires.

See Figure 1 on page 9. Note: there are two wires (white and green) in the bundle that are not used.

xJoin the two Molex connectors together, placing excess wiring and Molex connectors into the gang box.

ySlide the clock onto the metal mounting bracket installed in Step 1 and reinsert 6-32 screw from the top of the clock

into the mounting bracket hole. See Figure 2 on page 9.

zConnect eld wiring interconnecting the Clock/Timer with the ATSTCS Control Station to the appropriate

terminals of the Digital Clock/Timer See wiring detail on next page.

Chassis ground MUST be connected to conduit/Earth ground to provide proper protection from electric shock.

CAUTION: Electric Shock Hazard! When making installation, route eld wiring away from sharp projections, corners, and

internal components.

Make sure the SiteSync IQ system controller and other equipment is set up and operational. Note: Clocks should

be installed within 24 hours of installing the system controller. After 24 hours, the system controller will enter Quiet

Mode. If your system controller has a keypad, pressing 3-5-7 will disable Quiet Mode for 6 hours

Apply power to the circuit and conrm correct operation.

Upon startup, the clock will ash the version number and then correct on the rst valid signal. This should take less

than one minute. If the clock is not updating, review the steps listed above and consult the SiteSync IQ Installation and

Operation Manual for additional troubleshooting assistance.

SQA461RSxE Owner's Manual

AppendixMaintenance

Code Blue

OperationInstallationDescription

Control Station Installation

The ATSTCS Control Station can be mounted to a double gang box, 11/2inch deep or deeper. The Control Station can be

mounted up to 30 feet away from the Digital Clock/Timer. The recommended minimum interconnecting eld wire size is

#22.8 AWG stranded wire. Ensure that installation conforms to the National Electrical Code and local wiring codes.

CAUTION: Electric Shock Hazard! Ensure that no electrical power is present on any wire before installation.

uPull interconnecting eld wires into the double gang box.

vConnect eld wiring interconnecting the ATSTCS Control Station with the Digital Clock/Timer to the

appropriate wires of the Control Station. See wiring detail below.

wMount the Control Station to the double gang box using the machine screws provided.

K2+

K2–

K1+

K1–

12VAC

UNREG

GND

PIEZO

NOT USED

RED

BLACK

VIOLET

GREY

BROWN

BLUE

ORANGE

YELLOW

GREEN

WHITE

PIEZO

BUZZER

RESET

ENTER

START/STOP

INCREMENT

CLOCK

DOWN

SET

RUN

Green-Earth Gnd

White-Neutral line

Black-Hot line

Digital Clock/Timer

ATSTCS Control Station

20 ft. supplied cable. Can

be extended to 30 ft.

maximum using #22 AWG

wire (min.) with 1/32”

insulation (min.)

Figure 1

Figure 2

6-32 x 3/4black screw

secures device to the

mounting plate

Single or double gang

box (supplied by others)

must be securely mounted

Mounting plate

fastens to the

back box

Mounting plate detail

Typical wiring for the Digital Clock/Timer with Control Station

SQA461RSxE Owner's Manual

Appendix Maintenance

Code Blue

Operation Installation Description

Operation

Powering Up

Before applying power, place the SET/RUN switch to the RUN position and the UP/DOWN/CLOCK switch to the CLOCK position.

Apply power to the unit. The displays may rotate during the power on self test and then a version number will appear for a few

seconds. Once the receiver inside the clock receives a signal from the SiteSync IQ system controller, the clock will display and

begin keeping time. At rst startup the clock may display a time such as 1:00:00 until it receives the rst time update from the

SiteSync IQ system controller. This should only take a few seconds, after which the correct time from the SiteSync IQ system

controller should appear.

Setting Time

Setting of the time is not needed for the digital clock or timer control station. The time information is automatically updated

by the SiteSync IQ system controller. The 12- or 24-hour mode option is congured by the display settings of the system

controller.

The ATSTCS timer control station will allow the user to set a 12- or 24-hour mode and time when the SET/RUN switch is in the

SET position. However, as soon as the SiteSync IQ system controller updates the 12/24 hour mode chosen, the time will be

reset to the time sent by the SiteSync IQ system controller and the 12/24 hour mode congured in the system controller. Set

the SET/RUN switch to the RUN position and the UP/DOWN/CLOCK switch to the CLOCK position to return the clock display.

Setting the Up Counter Preset Time

If you want to use the alarm and hold feature with the UP timer, you will need to set a preset time for the UP timer.

Set the UP/DOWN/CLOCK switch to the UP position.

Set the SET/RUN switch to the SET position. The hours digits will be ashing.

Using the INCREMENT switch, set the desired hours for the preset time, then press ENTER. The minutes digits will now be

ashing.

Set the desired minutes the same way, then press ENTER. The seconds digits will then be ashing.

Set the desired seconds the same way, then press ENTER. The display will then ash donE.

Set the SET/RUN switch back to the RUN position.

Note: A preset of 00:00:00 allows the digital clock/timer to be used as a standard elapsed timer with a maximum elapsed time

of 30:59:59.

Tabla de contenidos

Otros manuales de Reloj de American Time

American Time

American Time WN261RSxE Manual de usuario

American Time

American Time SiteSync IQ Manual de instrucciones

American Time

American Time SiteSync IQ Manual de instrucciones

American Time

American Time SiteSync IQ Manual de usuario

American Time

American Time H004595 Guía de configuración

American Time

American Time H004817 Manual de usuario

American Time

American Time SSIQ Manual de instrucciones

American Time

American Time SiteSync IQ Manual de instrucciones

American Time

American Time ALLSYNC IQ Manual de instrucciones

American Time

American Time SiteSync IQ Manual de usuario

American Time

American Time SiteSync IQ Manual de instrucciones

American Time

American Time SiteSync IQ Instrucciones de funcionamiento

American Time

American Time PGE441RFE-W Manual de instrucciones

American Time

American Time ALLSYNC IQ MASTER Manual de instrucciones

American Time

American Time DSY261RSxE Manual de usuario

American Time

American Time SiteSynq IQ Manual de usuario

American Time

American Time Wi-Fi Battery Analog Clock Manual de instrucciones

American Time

American Time SiteSync IQ Manual de instrucciones

American Time

American Time Wi-Fi Clocks Manual de usuario

American Time

American Time SiteSync IQ Manual de instrucciones

American Time

American Time DSY261RSAE Manual de usuario

American Time

American Time AllSync Plus Manual de usuario

American Time

American Time SQA261RSAEA Manual de usuario

American Time

American Time AllSync IQ ASQMSTR-00X8E Manual de usuario

Manuales populares de Reloj de otras marcas

Silicon Laboratories

Silicon Laboratories SI5324 Manual de usuario

Heathkit

Heathkit GC-1005 Manual de usuario

Oregon Scientific

Oregon Scientific PRYSMA RMR221P Manual de usuario

Andrew O'Malley

Andrew O'Malley DOTKLOK Manual de usuario

ALGE-Timing

ALGE-Timing ASC3 Manual de usuario

Bodet

Bodet Profil 960 Manual de usuario

Nixie Clock

Nixie Clock Divergence Meter Manual de usuario

La Crosse Technology

La Crosse Technology WS-8256-AL Manual de usuario

Mini Gadgets

Mini Gadgets MCPro Manual de usuario

Casio

Casio TMR-200 Manual de usuario

Progetti

Progetti ILTEMPOSTRINGE Manual

BVItech

BVItech BV-101 Manual de usuario

Progetti

Progetti KALIMERO Manual

La Crosse Technology

La Crosse Technology WT-3141b Manual

La Crosse Technology

La Crosse Technology W86531 Manual de usuario

Sharp

Sharp SPC900 Manual de usuario

La Crosse Technology

La Crosse Technology 404-50447 Manual de usuario

Datexx

Datexx DF0063 Manual de usuario