American Standard 2390 Manual de usuario

AMERICAST®LIMITED LIFETIME WARRANTY

If an American-Standard Americast® brand product is found to be defective in

materials or workmanship, after inspection by an authorized American-Standard

representative, American-Standard will repair or, at its option, exchange the product for

a similar model. This warranty extends for the lifetime of the product, so long as it

remains in use in its original place of installation, except that the warranty applies to a

bathing vessel’s slip-resisting surface only for the first year after the product’s initial

installation.

This warranty applies only to the original purchaser and installation of these

products.

This warranty does not apply to whirlpool components or to faucets, drains,

mounting rims, grab bars or other accessories. If manufactured or supplied by

American-Standard, such whirlpool components and accessories are covered under

separate limited warranties.

This warranty does not apply to local building code compliance. Since local building

codes vary considerably, the purchaser of this product should check with a local

building or plumbing contractor to assure local code compliance before installation.

This warranty shall be void if the Americast® brand product has been moved from

its initial place of installation; if it has been subjected to faulty maintenance, abuse,

misuse, accident or other damage; if it was not installed in accordance with American-

Standard’s instructions; or if it was modified in a manner inconsistent with the product

as shipped by American-Standard.

American-Standard's option to repair or exchange the product under this warranty

does not cover any labor or other costs of removal or installation, nor shall American-

Standard be responsible for any other incidental or consequential damages

attributable to a product defect or to the repair or exchange of a defective

product, all of which are expressly excluded from this warranty. (Some states or

provinces do not allow the exclusion or limitation of implied warranties, so this exclusion

may not apply to you.)

This warranty gives you specific legal rights. You may have other statutory rights that

vary from state to state or from province to province, in which case this warranty does

not affect such statutory rights.

For service under these warranties, it is suggested that a claim be made through the

contractor or dealer from or through whom the product was purchased, or that a service

request (including a description of the product model and of the defect) be sent to the

following address:

In the United States: AMERICAN STANDARD, INC.

P.O. Box 6820

Piscataway, New Jersey 08855

Attn: Director of Consumer Affairs

For residents of the United States, warranty information may also be obtained by

calling the following toll free number: (800)442-1902

In Canada: AMERICAN STANDARD, INC.

2480 Stanfield Road

Mississauga, Ontario Canada L4Y 1S2

Toll Free: (800) 387-0369

In Mexico: IDEAL STANDARD, S.A. de C.V

Customer Service Manager

Planta Santa Clara,Via Morelos #330

Santa Clara Coatitla

Ecatepec de Morelos 55540,

Estado de Mexico, Mexico

Princeton™Bath

Installation Instructions

1527mm

(60-1/8)

762mm

(30)

TUB WIDTH

LEVELING SUPPORT

STRINGER 51 x 102mm

(2 X 4)

FRAMING INSTRUCTIONS

Note recess is 1527 x 813mm (60-1/8 x 32). Cut a 229 x 305mm (9 x 12) hole in sub

floor for drain, centered 362mm (14-1/4) as shown for below floor rough. Locate studs

as required, then ensure rough opening dimensions are proper and supports are plumb

and square.

*Install stringer as shown (346mm [13-5/8] for through the floor drain or

435mm [17-1/8] for above the floor drain.)

362mm

(14-1/4)

Introduction: Thank you for selecting American-Standard...products which

have been the benchmarks of fine quality for over 100 years. To help insure

that the installation process will proceed smoothly, please read these instructions

carefully before you begin. Also carefully unpack and examine your new plumbing

fixture.

2390.202

2392.202 2391.202

2393.202

Observe Local Plumbing and Building Codes

790043-400 (Rev. G )

229 x 305mm

(9 x 12) FLOOR

CUTOUT

FOR DRAIN

813mm

(32)

790043-400 (Rev. G)

STUD

SHIM

DRY WALL

TILE

SEALANT

TUB

ROOFING NAIL

51 x 102mm (2 x 4) WOOD

STRINGER FULL LENGTH

STEEL

STUD

SHIM

DRY WALL WASHER

TILE

SEALANT

TUB

4" (102mm)

DRYWALL

SCREW

Below is shown typical cross sections of the tub rim showing

typical wall constructions.

AMERICAN

STANDARD

FINISHED TILE FLOOR

UNDERLAYMENT

SUB FLOOR

NAIL

DRYWALL

SCREW

EVERY STUD

Position bathtub within the recess, check level, front to back, side to side. Also

check drain clearance hole in sub floor. To secure the tub to wood studs, use

roofing nails immediately above the flange of the tub.

To secure the tub to steel studs, use drywall screws and flat washers. (See Step 4)

Caution: Take Extra Care When Driving Nails or Screws To Avoid Damaging

The Tub.

The tile or similar finished floor will be butted against the bottom of the

tub apron also holding the tub in place.

WOOD STUDS STEEL STUDS

AMERICAN

STANDARD

Install the overflow and

drain assembly onto the

tub per manufacturer's

instructions.

DRAIN

229 x 305mm

9" X 12" HOLE IN SUB FLOOR

FOR BELOW FLOOR ROUGH

762mm

30"

1524mm

60"

19mm

3/4"

362mm

14-1/4"

ROUGH

FLOOR

*PLUMBER NOTE: PROVIDE FULL

LENGTH SUPPORT STRINGER

AT THIS POINT

FINISHED

WALL

48mm

1-7/8"

FINISHED

WALL

197mm

7-3/4"

445mm

17-1/2"

349mm

13-3/4"

ROUGH

FLOOR

356mm

14"

BELOW FLOOR ROUGH

2390.202 2391.202

ABOVE FLOOR ROUGH

2392.202 2393.202

64mm

2-1/2"

DIA.

23mm

15/16" 64mm

2-1/2"

64mm

2-1/2"

DIA.

23mm

15/16" 64mm

2-1/2"

FINISHED

WALL

89mm

3-1/2"

FULL LENGTH

SUPPORT STRINGER

LEFT HAND TUB ILLUSTRATED

RIGHT HAND TUB IS REVERSED

STD. 1-1/2

DRAIN OUTLET

19mm

3/4"

60mm

2-3/8"

1527mm

(60-1/8)

762mm

(30)

TUB WIDTH

LEVELING SUPPORT

STRINGER 51 x 102mm

(2 X 4)

Note recess is 1527 x 813mm (60-1/8 x 32). Cut a 229 x 305mm (9 x 12) hole in sub

floor for drain, centered 362mm (14-1/4) as shown for below floor rough. Locate studs

as required, then ensure rough opening dimensions are proper and supports are plumb

and square.

*Install stringer as shown (346mm [13-5/8] for through the floor drain or

435mm [17-1/8] for above the floor drain.)

362mm

(14-1/4)

229 x 305mm

(9 x 12) FLOOR

CUTOUT

FOR DRAIN

813mm

(32)

Princeton™ Bath

w/Integral Overflow

Installation Instructions

Introduction:

FRAMING INSTRUCTIONS

Thank you for selecting American-Standard...products which

have been the benchmarks of fine quality for over 100 years. To help insure

that the installation process will proceed smoothly, please read these

instructions carefully before you begin. Also carefully unpack and examine your

new plumbing fixture.

2390.202.ICH

2392.202.ICH 2391.202.ICH

2393.202.ICH

2390.202.IPB

2392.202.IPB 2391.202.IPB

2393.202.IPB

Observe Local Plumbing and Building Codes

LEFT HAND TUB ILLUSTRATED

RIGHT TUB IS REVERSED

791174-100 Rev. G

The Drain Assembly is enclosed with tub models

listed above-locate and retain for tub installation

before discarding tub carton

IMPORTANT

1524mm

(60)

762mm

(30)

FINISHED

WALL

19mm

(3/4)

FINISHED

WALL

FULL LENGTH

SUPPORT STRINGER

OUTLINE OF

SKID PATTERN

197mm

(7-3/4)

9 x 12

HOLE IN SUB-FLOOR

PROVIDE FULL

LENGTH SUPPORT

STRINGER

AT THIS POINT

362mm

(14-1/4)

48mm

(1-7/8)

346mm

(13-5/8)

60mm

(2-3/8)

89mm

(3-1/2)

ROUGHING-IN

1-1/2 N.P.S.M.

THREADS

1-1/2 TUBING

THREAD INSIDE

ROUGH

FLOOR

445mm

(17-1/2)

PROVIDE FULL

LENGTH SUPPORT

STRINGER

AT THIS POINT

435mm

(17-1/8)

DRAIN

SHOE

FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.

BELOW FLOOR ROUGH

2390.202 ICH

2391.202 ICH

ABOVE FLOOR ROUGH

2392.202 ICH

2393.202 ICH

356mm

(14) ROUGH

FLOOR

791174-100 Rev. G

INSTALLATION

AMERICAN

STANDARD

FINISHED TILE FLOOR

UNDERLAYMENT

SUB FLOOR

NAIL

DRYWALL

SCREW

EVERY STUD

Remove Lift and Turn Stopper and Tailpiece Assembly from box and check that all

parts are included. Remove Lift and Turn Stopper Assembly from Tailpiece by setting

Stopper to closed position, and turning Stopper Knob counter-clockwise.

(Re-install Stopper after Drain installation is completed.)

Apply plumbers putty around drain hole and pipe thread compound on threaded

end of tailpiece.

Set Tailpiece in drain hole. (Lift and Turn Stopper Assembly should be removed,

and reinstalled after tub installation is completed.)

From underside of tub: Place Rubber Wedge Seal on Tailpiece, small end toward tub,

and center in hole, place Brass Washer on Tailpiece, and thread on Locking Nut, flange

side first. Tighten Locking Nut to obtain a uniform seal between Wedge Seal

and hole in tub.

DO NOT OVERTIGHTEN!

Final hook up to tub waste can be made using either internal threads in Tailpiece

(1-1/2 tubing 1-1/2—28 thd.), or external threads on Tailpiece (1-1/2—11-1/2 NPSM)

for appropriate tub fittings.

DRAIN INSTALLATION

TAILPIECE

RUBBER

DRAIN SEAL

BRASS DRAIN

WASHER

BRASS

DRAIN NUT

STOPPER

ASSEMBLY

STOPPER

KNOB

LIFT AND TURN

STOPPER ASSEMBLY

SET

TAILPIECE APPLY PIPE JOINT

COMPOUND TO

THREADS

APPLY PLUMBERS

PUTTY

ASSEMBLE AND

TIGHTEN

TURN TO

REMOVE

STOPPER IN

CLOSED POSITION

(UNSCREW STOPPER ONCE IN

CLOSED POSITION TO REMOVE)

STOPPER IN

OPEN POSITION

STUD

SHIM

DRY WALL

TILE

SEALANT

TUB

2 x 4 WOOD

STRINGER

FULL LENGTH

ROOFING NAIL

2 x 4 WOOD

STRINGER

FULL LENGTH

STEEL

STUD

SHIM

DRY WALL WASHER

TILE

SEALANT

TUB

DRYWALL

SCREW

Below is shown typical cross sections of the tub rim

showing typical wall constructions.

WOOD STUDS STEEL STUDS

Position bathtub within the recess, check level, front to back, side to side. Also

check drain clearance hole in sub floor. To secure the tub to wood studs, use

roofing nails immediately above the flange of the tub.

To secure the tub to steel studs, use drywall screws and flat washers. (See Step 4)

Caution: Take Extra Care When Driving Nails or Screws To Avoid Damaging

The Tub.

The tile or similar finished floor will be butted against the bottom of the

tub apron also holding the tub in place.

NOTE: Warranty will be voided if the drain is installed after the tub has been

set in place.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Jacuzzi de American Standard

American Standard

American Standard Colony Whirlpool/Bathing Pool 1748 Series Manual de usuario

American Standard

American Standard Cadet Corner Whirlpool and Bathing Pool... Manual de usuario

American Standard

American Standard Cadenza Elite 6060E Manual de usuario

American Standard

American Standard 3260.210.AXX Manual de usuario

American Standard

American Standard 047186-0070A Manual de usuario

American Standard

American Standard WALK-IN BATH Guía de inicio rápido

American Standard

American Standard Cadet 2770.018 Manual de usuario

American Standard

American Standard WILLIAMSBURG ELITE 2806E Manual de usuario

American Standard

American Standard ELLISSE OVAL 2709 Manual de usuario

American Standard

American Standard Cadet Corner Whirlpool 2775.018H Manual de usuario

American Standard

American Standard Virtuoso 7236.028WC Manual de usuario

American Standard

American Standard SAVONA 2901.028 SERIES Manual de usuario

American Standard

American Standard Cadet 6'x42 2774.018 Manual de usuario

American Standard

American Standard Cadet 2773E Manual de usuario

American Standard

American Standard Cadet Whirlpool with Integral Apron... Manual de usuario

American Standard

American Standard Cadet 2773.018H Manual de usuario

American Standard

American Standard Cadet 2772.018H Manual de usuario

American Standard

American Standard 1748 Manual de usuario

American Standard

American Standard Acrylux Builder Series 6030Y2A.102.XXX Manual de usuario

American Standard

American Standard Renaissance 2771VA Manual de usuario

American Standard

American Standard Cadet 2776.XXXW Series Manual de usuario

American Standard

American Standard Cadet Elite 2773EC Instrucciones de funcionamiento y seguridad

American Standard

American Standard Cadet 2770.XXXW Series Manual de usuario

American Standard

American Standard 2651.110.AXX Manual de usuario

Manuales populares de Jacuzzi de otras marcas

Bestway

Bestway Lay-Z-Spa 54189 Manual de usuario

Jacuzzi

Jacuzzi ARGA ARG101C0110 Manual de lista de piezas

Morphy Richards

Morphy Richards Essentials PC4006 Manual de usuario

Softub

Softub PRESTIGE Manual de usuario

JNJ SPAS

JNJ SPAS SPA-318 Manual de instalación

KIRAMI

KIRAMI Comfort Family Manual de usuario

QCA Spa

QCA Spa VS501 PAK (VL260 TOPSIDE) Manual de usuario

HoMedics

HoMedics FB-655HJ-GB Manual de usuario

Everyday Hot Tubs

Everyday Hot Tubs 530 Manual de usuario

anko

anko SS-601A Manual de usuario

Jacuzzi

Jacuzzi Duetta 6042 Manual de usuario

Pooli

Pooli OS030979B Manual de usuario

Jacuzzi

Jacuzzi alimia Manual de usuario

ab Solares Smart Spa Manual de usuario

CalderaSpas

CalderaSpas CalderaSpas Utopia Series Manual de usuario

Outsunny

Outsunny 848-047V70 Manual de usuario

Aquatic

Aquatic INFINITY 1 Manual de usuario

Master Spas

Master Spas MP Force Manual de usuario