American Dynamics AD2096A Manual de usuario

Installation and Operating Instructions

This manual describes the installation and operating procedures for the American Dynamics AD2096A Alarm Interface Unit.

The AD2096A Alarm Interface Unit, when used with American Dynamics Matrix Switching Systems, automatically calls

specified cameras and preset scenes to specified monitors when contacts are activated external to the system.

Model AD2096A

Alarm Interface Unit

The software/firmware furnished with this equipment is confidential to and is copyrighted by SENSORMATIC ELECTRONICS

CORPORATION. It is not to be copied or disclosed in any manner without the express written consent of SENSORMATIC. The

software/firmware is furnished to the purchaser under a license for use on a single system.

Information furnished by SENSORMATIC is believed to be accurate and reliable. However, no responsibility is assumed by

SENSORMATIC for its use; nor for any infringements of other rights of third parties which may result from its use. No license is

granted by implications or otherwise under any patent or patent rights of SENSORMATIC.

The installation of this product should be made by qualified

service personnel and should conform to all local codes.

QA301D

WWAA

AARR

RRNN

NNIIIINN

NNGG

To reduce the risk of fire or shock hazard, do

not expose this product to rain or moisture.

AMERICAN

DYNAMICS

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVERS (OR BACK) .

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION !

The lightning flash with arrowhead

symbol, within an equilateral

triangle, is intended to alert the

user to the presence of uninsulated

"dangerous voltage" within the

product's enclosure that may be of

sufficient magnitude to constitute a

risk of electric shock to persons.

The exclamation point within an

equilateral triangle is intended to

alert the user to the presence of

important operating and maintenance

(servicing) instructions in the

literature accompanying the product.

UUNN

NNPP

PPAA

AACC

CCKK

KKIIIINN

NNGG

AANN

NNDD

IIIINN

NNSS

SSPP

PPEE

EECC

CCTT

TTIIIIOO

OONN

Unpack carefully. This is an electronic product and should

be handled as such. Compare the items received with the

packing list with your order.

Be sure to save:

1. The shipping cartons and insert pieces. They are the )

safest material in which to make future shipments of

the product.

2. The IMPORTANT SAFEGUARDS sheet.

3. These Installation and Operating Instructions.

MMAA

AAIIIINN

NNTT

TTEE

EENN

NNAA

AANN

NNCC

CCEE

User maintenance of this unit is limited to external cleaning

and inspection. For specific recommendations refer to the

IMPORTANT SAFEGUARDS sheet packaged with this product.

IIIINN

NNSS

SSTT

TTAA

AALL

LLLL

LLAA

AATT

TTIIIIOO

OONN

AANN

NNDD

SSEE

EERR

RRVV

VVIIIICC

CCEE

If you require information during installation of this

product or if service seems necessary, contact the

Sensormatic Repair and Service Department at (800)

442-2225. You must obtain a Return Authorization Number

and shipping instructions before returning any product for

service.

Do not attempt to service this product yourself. Opening or

removing covers may expose you to dangerous voltages or

other hazards. Refer all servicing to qualified personnel.

This equipment has been tested and

found to comply with Part 15 of the

FCC Rules.

Operation is subject to the

following two conditions: 1. This

device may not cause harmful

interference, and 2. This device

must accept any interference

received, including interference

that may cause undesired operation.

CONTENTS

Page

DESCRIPTION.............................................................................. 1

FEATURES .................................................................................... 1

INSTALLATION............................................................................ 1

Mounting.................................................................................... 1

SETUP............................................................................................ 2

Block (Alarm Contact) Setup .................................................... 2

Input Type Setup........................................................................ 2

Baud Rate Setup ........................................................................ 2

CONNECTIONS............................................................................ 3

Alarm Inputs.............................................................................. 3

Alarm Relay Output................................................................... 3

RS-232 Connection.................................................................... 3

Cascading Multiple Units .......................................................... 3

OPERATION.................................................................................. 4

Power Sources ........................................................................... 4

Powering Up.............................................................................. 4

Alarm Response Operation........................................................ 4

Programming Alarm Contacts................................................... 4

TYPICAL SYSTEM CONNECTIONS

AD2096A to AD1650 Series................................................. C-2

AD2096A to AD1995............................................................ C-3

AD2096A to AD1996............................................................ C-4

AD2096A to AD2150/2350................................................... C-5

Cascading AD2096A units .................................................... C-6

AD2010DBVL to AD2096A................................................. C-7

INDEX

SPECIFICATIONS......................................................... Rear Cover

DESCRIPTION

The AD2096A Alarm Interface Unit (AIU) is used with

American Dynamics Matrix Switching Systems to provide

automatic callup of a camera to a monitor when a specific

alarm switch/contact input is activated. Each AD2096A AIU

is set up to identify the matrix system video input and preset

scenes with which it will be associated. The AD2096A has the

capability to respond to 64 alarm inputs. The number of alarm

inputs can be increased by cascading multiple AD2096A units.

FEATURES

•UNIVERSAL MOUNT CABINET

•LED POWER INDICATOR ON REAR PANEL

•LED ALARM INDICATOR ON REAR PANEL

•DIP SWITCH SELECTION TO SET BAUD RATE

•DIP SWITCH SELECTION FOR CAMERA GROUP

•DIP SWITCH SELECTION TO ACCEPT NORMALLY

OPEN OR NORMALLY CLOSED INPUTS

•SCREW TERMINAL WIRE CONNECTORS

•TERMINALS AVAILABLE TO ACTIVATE VCR OR

OTHER DEVICES

INSTALLATION

This installation should be made by qualified service personnel

and should conform to all local codes. Safeguards must be

taken to avoid unintentional operation by employees and

maintenance personnel working about the premises, by falling

objects, by customers, by building vibration, and by similar

causes.

Mounting

The AD2096A cabinet may be surface or rack mounted in any

convenient location with adequate ventilation. See Figure 2

for illustration of the mounting options.

• The AD2096A is shipped with mounting ears installed flush

with the front panel, and can be mounted to the front of a

standard 19" rack.

• The ears of the AD2096A can be removed and placed such

that they are flush with the rear panel. This allows the

AD2096A to be mounted to the rear of a rack that is

equipped with mounting channels.

• The AD2096A can be mounted to the wall by installing the

ears perpendicular the sides of the unit. The bottom or top

covers can face toward the wall and the front or rear panel

face upwards.

The AD2096A AIU is two rack units in height (3.5") and one

unit wide (19"). For proper ventilation allow at least three feet

(1m) from the rear of the racks to any wall and one EIA rack

height (1 3/4"/4.5cm) between units.

AD2096A ALARM INTERFACE UNIT

ALARM

POWER

120V

60Hz

AAAAAA

AAA AA A

AAAAAA

AAA AA A

AAAAAA

SELECT

ABCDEFGH

N N C

O C M

AAA A

INPUT OUTPUT

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48

49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64

Figure 1 - AD2096A Alarm Interface Unit Rear Panel

FRONT OR REAR PANEL

RACKCHANNEL

TOP OR BOTTOM COVER

WALL

FRONT OR REAR PANEL

TOP COVER

MOUNTING EARS

Figure 2 - Mounting Options

SETUP

Three 8-position DIP switches are used for AD2096A setup.

The first two switches, S1 and S2, are located on the rear panel

(see Figure 1, page 1). The top switch, S1, identifies the block

of 64 alarm contacts (out of a possible 1024) which are

connected to the AD2096A. The lower switch, S2, configures

the AD2096A for either Normally Open (NO) or Normally

Closed (NC) alarm contacts within each group of eight inputs

of the selected block. Each group may be set to a different

input type. The third switch, S3, is located internally on the

AD2096A PC board (see Figure 3), and is used to select the

RS-232 COM ports baud rates.

Tables 1, 2, and 3 show the switch settings which correspond

to each DIP switch. A user fill-in block is provided under each

table for the installer to record the switch settings.

Table 1 - S1, Block Setup

0 = OFF, 1 = ON

ALARM INPUT SWITCH POSITIONS

BLOCK CAMERAS A B C D E F G H

1 1-64 00000000

2 65-128 00000001

3 129 - 192 0 0 0 0 0010

4 193 - 256 0 0 0 0 0011

5 257 - 320 0 0 0 0 0100

6 321 - 384 0 0 0 0 0101

7 385 - 448 0 0 0 0 0110

8 449 - 512 0 0 0 0 0111

9 513 - 576 0 0 0 0 1000

10 577 - 640 0 0 0 0 1001

11 641 - 704 0 0 0 0 1010

12 705 - 768 0 0 0 0 1011

13 769 - 832 0 0 0 0 1100

14 833 - 896 0 0 0 0 1101

15 897 - 960 0 0 0 0 1110

16 961 - 1024 0 0 0 0 1111

Table 2 - S2, Input Type Setup

0 = OFF (Normally Open, NO)

1 = ON (Normally Closed, NC)

ALARM SWITCH ALARM INPUT STATE

INPUT #s POSITION NO NC

1 - 8 H 0 1

9 - 16 G 0 1

17 - 24 F 0 1

25 - 32 E 0 1

33 - 40 D 0 1

41 - 48 C 0 1

49 - 56 B 0 1

57 - 64 A 0 1

The baud rate of the two COM ports (INPUT and OUTPUT) is

factory set at 1200. Verify the baud rate of the system being

connected to the AD2096A by referring to the applicable

system installation and operation manual. To change the baud

rate of either port, select the correct DIP switch position by

referring to Table 3 below. The two COM ports may be set to

different baud rates, as indicated in the table.

Table 3 - S3, Baud Rate Setup

0 = OFF, 1 = ON

SWITCH POSITIONS

BAUD COM INPUT COM OUTPUT

RATE 1 2 3 4 5 6 7 8

300 0000 0000

600 0001 0001

1200 0010 0010

2400 0011 0011

4800 0100 0100

9600 0101 0101

19200 0110 0110

ALARM INTERFACE UNIT AD2096A

CAMERA BLOCK

INSTALLERS NOTES - TABLE 1

INSTALLER'S NOTES - TABLE 3

BAUD RATE

IN OUT

INSTALLERS NOTES - TABLE 2

ALARM INPUT

CONFIGURATION

FEDCBAGH

Dip Sw it ch

Power Cord

1OFFON

Figure 3 - AD2096A PCB Layout

CAUTION - Due to the presence of non-

insulated components with hazardous

voltages, the following internal adjustments

should be performed by qualified service

personnel only.

CONNECTIONS

Alarm Inputs

Eleven 12-pin connectors are provided on the rear panel of the

AD2096A for alarm inputs. A mating screw-terminal

connector, below, is supplied for each rear panel connector.

Each connector is labeled with an alarm number (1 - 64), an

"A", and a ground symbol. The "A" stands for alarm contact

and the ground symbol for ground. Each alarm input connector

contact open circuit voltage is 5.0 VDC. Closed circuit current

is 0.2 mA, and a normally closed condition requires less than

15K ohms between “A” and ground.

Connections are made by inserting alarm contact and ground

wires into the slots of the mating connectors and tightening the

hold down screws. When all wires have been connected, insert

the 12-pin connectors into the rear panel connectors.

Alarm Relay Output

The lower right connector on the rear of the AD2096A is a 12-

pin connector which provides access to both Normally-Open

(NO) and Normally-Closed (NC) contacts of an internal alarm

relay. This relay is active when any alarm input is received

(see page 4). The maximum relay contact ratings are: 0.25

amps current @ 30 Volts DC or RMS, and 10 VA power. A

mating screw-terminal connector is provided.

RS-232 Connectors

The two RS-232 COM connectors on the rear panel of the

AD2096A are 8-pin, modular type RJ-45 connectors. One (1)

8-pin terminal box 2113-0019-01 and one (1) 7-foot modular

cable 6003-0047-02 are supplied with each AD096A for

connections to these ports.

The RS-232 port labeled COM OUTPUT is connected to a

switching system input port or to another AD2096A AIU (see

Cascading, below) using the supplied modular cable when

distances between the units are no further than 7' apart.

For connection where distances exceed 7', or for connection to

an AD1995 MegaPower CPU, the terminal box is used. Table

4 gives the pinouts for the terminal box. The maximum

distance between terminal boxes shall not exceed 1000' (330m)

using 18 AWG shielded cable, Belden 8770 or equivalent.

Table 4 - RS-232 Terminal Box Pinouts

Pin Function

1 No Connection

2 Shield

3 No Connection

4 RCD

5 XMIT

6 No Connection

7 GND

8 No Connection

Cascading Multiple Units

If more than 64 alarm contacts are required, multiple

AD2096A units can be cascaded. If the units are within 7' of

the other, connect a modular cable from the COM OUTPUT

port of the last AD2096A unit to the COM INPUT port of the

next unit. If the AD2096A units are greater than 7' apart,

terminal boxes must be used for port connections. Refer to the

Typical System Connection for illustration of cascading.

AD2096A ALARM INTERFACE UNIT

AAAAAA

HOLD DOWN SCREWS

INSERT CONNECTOR

THIS DIRECTION

Figure 4 - Alarm Input Terminal Connector

HOLD DOWN SCREWS

INSERT CONNECTOR

THIS DIRECTION

Figure 5 - Alarm Relay Terminal Connector

Figure 6 - Terminal Box 2113-0019-01

Use NEC Class 2 wiring only for all external

connector pin connections. The wiring should also

conform to all local codes.

OPERATION

Power Sources

Power is supplied via the appended 3-wire power cord. Power

consumption is approximately eight watts.

The AD2096A is configured for 120VAC, 50/60Hz,

primary power source. Operating power voltages must be

held within the 105V and 125V range.

The AD2096-1 is configured for a 230VAC, 50/60 Hz

primary power source. Operating power voltages must be

held within the 198V and 250V range.

Powering Up

The AD2096A AIU does not contain a power On/Off switch.

A green POWER LED indicator, located on the rear panel,

illuminates when power is applied. If an alarm input is

activated, the green ALARM LED on the rear panel will

illuminate.

The 120 VAC units are supplied with a pendant 3-wire cord

and plug for mating to the primary source outlet. The 230 VAC

units are supplied with a Euro-style IEC 320 type inlet. A

suitable, detachable cord should be connected between the IEC

320 inlet and power source. The cord should conform to all

national and local use code requirements.

Note: DO NOT CONNECT THE EQUIPMENT TO THE

POWER SOURCE UNTIL READY TO POWER UP.

THE SOCKET OUTLET SHALL BE LOCATED

NEAR THE EQUIPMENT, AND SHALL BE

READILY ACCESSIBLE.

Make all connections to the AD2096A Alarm Inputs and

Output Relay connections and set the DIP switches as

indicated on page 2 before applying power to the AD2096A.

Alarm Response Operation

Each alarm input signal is assigned an alarm contact number

(ACN) by the AD2096A. The setting of DIP switch S1 (see

page 2) determines the range of ACN’s for each AD2096A.

Depending on the Matrix Switching System capabilities, a

maximum of 1024 alarm contacts (ACN’s) can be programmed

for alarm event response by that system.

When an alarm condition exists, the AD2096A AIU detects the

closure (or opening) of the contact, depending on the DIP

switch configuration (S2, page 2). The AD2096A AIU then

issues an alarm message containing the corresponding alarm

contact number (ACN), via the RS-232 COM OUTPUT Port,

to the Matrix Switching System for camera callup to monitors.

When an alarm contact is detected, the AD2096A AIU also

activates an internal relay, providing both an output closure

(NO pin) and an opening (NC pin); this relay output can be

used to turn on/off lights, VCRs, etc. The alarm relay output

continues to be active until the alarm condition is removed.

Once the alarm condition is deactivated (contact is cleared),

the alarm relay is held for 10 seconds, then is deactivated.

Programming Alarm Contacts

Each alarm contact (ACN) input to an AD Matrix Switching

System is armed for camera callup on a specific monitor.

Individual camera inputs and camera salvos, each with preset

scenes and auxiliary actions, may be programmed for

automatic callup to monitors in response to alarm inputs.

When the switching system is armed for alarm contact (ACN)

inputs, the video input associated with the ACN is

automatically displayed when that alarm input is detected by

the AD2096A AIU and sent to the switching system. Refer to

the Alarm Programming sections in the appropriate Matrix

Switching System Installation Manual for the commands to

arm alarm contacts, monitors, and cameras.

ALARM INTERFACE UNIT AD2096A

IF YOU ENCOUNTER ANY PROBLEMS

OPERATING THIS UNIT, OR NEED ASSISTANCE,

CALL OUR TECHNICAL SUPPORT CENTER:

within the United States 1-800-442-2225

outside the United States (845) 624-7640

Tabla de contenidos

Otros manuales de Sistema de seguridad de American Dynamics

American Dynamics

American Dynamics MegaPower 3200 Manual de servicio

American Dynamics

American Dynamics Intellex 2.0 Manual de instalación y operación

American Dynamics

American Dynamics AD2052 Guía del usuario

American Dynamics

American Dynamics Intellex DV16000 Manual de instalación y operación

American Dynamics

American Dynamics DigiMux DG4004 Manual de usuario

American Dynamics

American Dynamics AD2032 Manual de usuario

American Dynamics

American Dynamics AD1273 CobraDome Manual de usuario

American Dynamics

American Dynamics Intellex Digital Recorder Manual de usuario

American Dynamics

American Dynamics Intellex DV16000 Instrucciones de instalación y funcionamiento

American Dynamics

American Dynamics Intellex DV16000 Manual de usuario

American Dynamics

American Dynamics Intellex DV8000 Manual de usuario

American Dynamics

American Dynamics Intellex Ultra Manual de usuario

American Dynamics

American Dynamics AD2010N Manual

American Dynamics

American Dynamics MegaPower 3200 Manual de usuario

American Dynamics

American Dynamics VideoEdge Guía

American Dynamics

American Dynamics RABW4QUAD Instrucciones de montaje

American Dynamics

American Dynamics MegaPower 3200 Manual

American Dynamics

American Dynamics Intellex Ultra Manual de usuario

American Dynamics

American Dynamics AD2032 Manual de usuario

Manuales populares de Sistema de seguridad de otras marcas

Inner Range

Inner Range Concept 2000 Manual de usuario

Climax

Climax Mobile Lite R32 Instrucciones de montaje

CADDX

CADDX NX-6 Manual de usuario

FBII

FBII XL-31 Series Manual de usuario

Johnson Controls

Johnson Controls PENN Connected PC10 Manual de usuario

Aeotec

Aeotec Siren Gen5 Manual de usuario

Blaupunkt

Blaupunkt SA 2700 Manual de usuario

IDEAL

IDEAL Accenta Manual del propietario

AJAX

AJAX DoubleButton Manual de usuario

Swann

Swann SW-P-MC2 Manual de usuario

Ecolink

Ecolink Siren+Chime Manual de usuario

Digital Monitoring Products

Digital Monitoring Products XR150 Manual de usuario

EDM

EDM Solution 6+6 Wireless-AE Manual de usuario

Highway Safety Group

Highway Safety Group EA401 Manual de usuario

Siren

Siren LED GSM Manual de usuario

Detection Systems

Detection Systems 7090i Instrucciones de montaje

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manual de usuario

Siemens

Siemens FDM273 Manual de usuario