American Dynamics SpeedDome RASEL Series Instrucciones de instalación y mantenimiento

SPEEDDOME OPTIMA LT INDOOR CAMERA DOME INSTALLATION AND SERVICE GUIDE (8200-0181-01, REV. C)

1 of 14

SpeedDome®

Optima LT Indoor

Camera Dome

RASEL Series

Installation and Service Guide

The SpeedDome Optima LT indoor camera dome

mounts either to a hard ceiling or to a 2x2 tile

ceiling using a mounting plate (instructions for the

plate are supplied separately).

CAUTION: Save the box and packing

materials. These materials are required

should you need to ship the dome to a

repair center.

Note: The dome accepts either cable or conduit. If

running cable through a plenum ceiling, either

plenum-rated cable or flexible conduit is required.

Contents

Warnings ............................................................2

Before You Begin ...............................................3

Installation ..........................................................6

Troubleshooting .................................................9

Parts List for Authorized Users ........................10

Specifications ...................................................12

Declarations .....................................................14

Customer Support

If you need assistance, contact your sales

representative.

SPEEDDOME OPTIMA LT INDOOR CAMERA DOME INSTALLATION AND SERVICE GUIDE (8200-0181-01, REV. C)

2 of 14

Warnings

Please review the following warnings before you

install or service the camera dome.

ALWAYS USE:

· Proper safety equipment for the location and

type of installation.

· Proper lift equipment to reach the installation.

· Safety features of the lift equipment.

BE SURE:

· Electrical power is not connected to the dome

when connecting wires. Camera will move when

power is applied.

· Electrical power is not connected to nearby

fixtures that you might touch during installation.

DO NOT install this dome in hazardous areas

where highly combustible or explosive products are

stored or used.

This dome runs on 24Vac. DO NOT connect line

voltage to this dome.

North America power requirements: In North

America, this device is intended to be supplied

from a Class 2 power supply.

This installation should be made by a qualified

service person and should conform to all local

codes.

EU power requirements: This product runs on

24Vac. In the EU, it is intended to be powered from

a Limited Power Source. A limited power source is

a certified source of SELV, and if inherently limited,

with 8 amps maximum output current, and a

maximum of 100VA available; or if not inherently

limited, fused with a maximum value of 3.3 Amps,

meeting section 2.11 of IEC950, and a maximum of

250VA available. The power supply can be

obtained through Sensormatic or through another

source where the provider can furnish the

verification. This is required to assure electrical

safety in the product.

Stromanforderungen in der EU: Dieses Produkt

wird mit 24 V Wechselstrom betrieben. In der EU

ist es für den Betrieb durch eine begrenzte

Stromquelle vorgesehen. Eine begrenzte

Stromquelle ist eine zertifizierte SELV-Quelle

(Schutzkleinspannung), bei inhärenter Begrenzung

mit einem maximalen Ausgangsstrom von 8 A und

100 VA maximaler Verfügbarkeit, bei nicht

inhärenter Begrenzung mit einer maximalen

Sicherung von 3,3 A gemäß Abschnitt 2.11 der

IEC950 und 250 VA maximaler Verfügbarkeit. Das

Netzteil kann über Sensormatic oder eine andere

Quelle bezogen werden, wobei der Anbieter den

Nachweis der Konformität bereitstellen sollte. Dies

ist zur Gewährleistung der elektrischen Sicherheit

des Produktes erforderlich.

SPEEDDOME OPTIMA LT INDOOR CAMERA DOME INSTALLATION AND SERVICE GUIDE (8200-0181-01, REV. C)

3 of 14

Before You Begin

To ensure a smooth and successful installation,

observe the following requirements.

General Requirements

· Have electrical work comply with latest national

electrical code, national fire code, and all

applicable local codes and ordinances.

· Coordinate work with other trades to avoid

interference.

· Verify existing site conditions and coordinate

with the owner’s representative and appropriate

utilities as required.

· Obtain copies of all related plans, specifications,

shop drawings and addenda to schedule and

coordinate related work.

· Thoroughly review the project to ensure that all

work meets or exceeds the above requirements.

Bring alleged discrepancies to the attention of

the CCTV Project Coordinator.

Mounting Requirements

Mounting space: Ensure there is the following

space above the ceiling to accommodate the

dome.

Height above ceiling: 170mm (6.7in)

Diameter: 192mm (7.5in)

Structural members: Verify that ceiling members

can support the camera dome and mounting

structure, if used.

Weight: 2.5kg (5.5 lbs)

Cable Requirements

Data cables: The following table shows cable

requirements for SensorNet and Manchester

networks. For more information about

communication protocols and cable networks, see

Communication Protocols and Cable Networks,

8000-2573-19.

Data cable requirements

SensorNet Manchester

Cable type 1

unshielded,

twisted

pair*

shielded

twisted

pair**

Wire gauge 22 AWG 18 AWG

Connection Non-

polarized

Polarized

Max.

devices per

cable run

32 3

* Power, data, and video cables can be ordered

separately or within a composite cable that can be

ordered in various lengths. Plenum-rated cables must

be used in indoor ceilings used for environmental air

return (called "other air space" in the National

Electrical Code). Order parts through your distribution

network.

Note: If you order cable from an outside source, wire

colors may be different.

** Belden 88760 (plenum), or Belden 8760 cable (non-

plenum) cable is recommended. Plenum-rated cables

must be used in indoor ceilings used for environmental

air return (called "other air space" in the National

Electrical Code). Order cable directly from

Belden by calling 1-800-235-3361.

Plenum ceilings: Cable must be rated for plenum

or routed through flexible conduit. A cover plate for

the dome accepts ½" conduit.

WARNING! Do not run cables adjacent

to or in the same conduit as line voltage

mains power.

Power cables. Make power cable lengths as short

as possible to minimize the affects of low line

voltages and outdoor cold temperature perform-

ance. Maximum cable length between a Class 2

LPS (low voltage) ac source, such as a J-box, and

the dome depends on the ac line voltage. See the

tables below for maximum cable lengths based on

the worst-case low line voltages.

The line voltage must not go below the voltage

shown for the dome to be able to power up and

operate at the corresponding distances shown.

Typically cable distances are used that provide a

15% margin between nominal and low line

conditions. For example, if the nominal voltage

measures 120Vac, restrict the cable length to the

distance for .85 x 120 or approximately 100Vac.

SPEEDDOME OPTIMA LT INDOOR CAMERA DOME INSTALLATION AND SERVICE GUIDE (8200-0181-01, REV. C)

4 of 14

Power cable requirements—Indoor Dome

The following table shows the maximum cable

distance for several worst-case low line voltages

between various indoor power sources and the

indoor SpeedDome Optima. These distances are

for Sensormatic composite cables, which use 18

AWG ac power wires.

This table applies to domes produced after October

of 2001; distances are much less for earlier domes.

Twisted Pair Adapter

The ADACTP01BNC Twisted Pair Adapter

(supplied) can be used to transmit video or video

with up-the-coax (UTC) dome control signals over

unshielded twisted pair (UTP) cables, point-to-

point, up to 300m (1000ft).

The adapter mounts directly to the video source or

receiver without additional cabling and uses

Category 2-6 twisted pair wires to transmit the

video and dome control signals. The adapter does

not require power.

One adapter is supplied. If used, another adapter

must be ordered to for the connection at the other

end of the cable. The figure below shows twisted

pair cable connections. See installation guide

8200-0298-01 for details.

Indoor Dome Worst-Case Meters

AC Power Source Low Line V (Feet)

28 VA 117 130 (425)

Transformer 100 80 (250)

5604-0006-01 90 60 (200)

50 VA 117 160 (525)

Transformer 100 100 (325)

5604-0044-01 90 60 (200)

1-position SensorNet 117 160 (525)

RJ1SNUD 100 100 (325)

90 80 (250)

1-position SensorNet 240 160 (525)

RJ1SNUD-1 200 100 (325)

180 80 (250)

117 210 (675)

6-position SensorNet 100 130 (425)

Indoor J-Box 90 80 (250)

RJ6SN 240 210 (675)

200 130 (425)

180 80 (250)

Universal Transformer 117 130 (425)

0300-0914-01 100 100 (325)

90 60 (200)

Universal Transformer 240 160 (525)

0300-0914-03 200 100 (325)

180 80 (250)

Video Switcher/

Controller

Cat 2-6 UTP Cable

Twisted Pair Adapter

(Switcher/Controller End)

American Dynamics

Dome O

Fixed Camera

Twisted Pair Adapter

(Fixed Camera End)

Twisted Pair Adapter

(Dome End)

SPEEDDOME OPTIMA LT INDOOR CAMERA DOME INSTALLATION AND SERVICE GUIDE (8200-0181-01, REV. C)

5 of 14

SensorNet/Manchester Line Termination

SensorNet and Manchester communication

protocols require that the dome furthest from the

video controller or junction box be terminated.

Looking through the hole in the top of the dome,

ensure switch S1 is set to “terminated” for the

dome furthest from the video controller or junction

box. All other domes should be “un-terminated”.

Setting the Camera Address

Accessed through the hole in the top of the dome

are rotary switches SW1, SW2, and SW3. The

address range for SensorNet is 001 to 255. The

address range for Manchester is 0 to 64.

For example, for address 107, set SW3 to 1, SW2

to 0 (black dot), and SW1 to 7.

Compatibility with the VM96 Controller

If using a VM96 controller, the controller must be

Version 5.2 or higher.

Power-Up Routine

After power is connected to the dome, the dome

performs a homing routine. During the homing

process, the camera will pan and then either:

· Go to the start point of the “apple peel” pattern,

· If powered up once before, to the last position in

memory.

Once the camera stops, the camera is online and

is ready to be controlled.

Synchronizing Domes

To prevent picture rolling when switching from

camera to camera, all domes can be synchronized

to the ac source. A V-phase adjustment at the

control console enables the dome to sync to any

line phase.

Save Packaging Material

Should the camera dome need to be sent to a

repair center, use the packaging that the dome was

shipped in.

Plastic Bag

Box for

Bubble

SPEEDDOME OPTIMA LT INDOOR CAMERA DOME INSTALLATION AND SERVICE GUIDE (8200-0181-01, REV. C)

6 of 14

Installation

Parts required

Note: For installation to a tile ceiling, also order the

UL-approved RH2x2 Metal Plate Mounting Kit.

Install Kit 0352-0020-01

Connector, 3-position (power) 1 2109-0254-02

Connector, 2-position (data) 1 2109-0756-01

Wire, hanging 3.6m (12ft) 2898-0007-01

Card, quick connect 1 2402-2055-02

Template, cutout, hard mount 1 2402-2054-01

Procedure

Use the following steps when attaching the dome

to a hard ceiling.

1. Using template supplied, cut a hole in the

ceiling. Run power and data cables and the

video cable to the hole.

2. For ease of installation, adjust the two “swing

out” mounting clips for ceiling thickness.

3. To expose connectors and settings at the top

of the dome, remove the cover plate by

removing one screw and loosening the other.

Set the camera address.

As an example, address

107 is shown.

Address Switches

Terminated

Un-Terminated

Line

Termination

Switch

(S1)

x100 x10 x1

SW3 SW2 SW1

SensorNet / Manchester – Switch 6 & 7 "On", all others "Off"

Off

7654321

Comm. Select (S2)

AC 1

SNet 1 - No Polarity

2 - No Polarity

Manch. 1 - WHT

2 - BLK

Comm. (P9)

Video

24Vac (P10)

4. Set address switches SW1, SW2, and SW3 for

the address (for example: 001–016 for VM16,

001–096 for VM96).

5. If daisy-chaining domes, the dome furthest

from the video controller requires that termina-

tion switch S1 remain in the “terminated”

position (resistor symbol). All other domes

along the chain must be set to “un-terminated”.

6. Inside the opening, check communications

DIP switch S2 for the correct settings. For

SensorNet and Manchester, ensure switches 6

and 7 are “On”. Other switches should be “Off”.

7. Determine if conduit or cables will be used. If

using conduit, remove the Romex clamp and

use 1/2in. flexible conduit and appropriate

fittings. If using cables, they must be plenum-

rated if running through a ceiling plenum and

they must be secured using the cover plate

and Romex clamp.

8. Leaving .6m (2ft) of service loop so the dome

can be dropped from the ceiling for servicing,

run the cable through the cover plate and

Romex clamp, if used.

9. Remove 2.5-3.8cm (1–1.5in) of jacket from the

cable end and install power and data

connectors supplied.

10. Plug connectors to the board according to the

figure above.

11. If using conduit, attach it to the cover plate

using the appropriate fittings and then reattach

the cover plate. If using cable, reattach the

cover plate to the dome using two screws and

then tighten the Romex clamp against the

cable (required to maintain the Plenum rating).

Mounting Clip

SPEEDDOME OPTIMA LT INDOOR CAMERA DOME INSTALLATION AND SERVICE GUIDE (8200-0181-01, REV. C)

7 of 14

12. Attach a BNC connector to the video cable (if

not using the Twisted Pair Adapter). Also

attach the orange 3-pin power plug to

connector P10 and the gray 2-pin data

communications plug to connector P9. Wire

colors in diagram refer to cables supplied by

Sensormatic.

Note: Use a small screwdriver to tighten the

connector screws. DO NOT over tighten the

connectors!

13. Plug video (or Twisted Pair Adapter), power,

and data communications cables into their

mating connectors in the top of the dome

housing.

WARNING! Ensure power is off at

the source when connecting cables.

Otherwise, the dome will operate

during installation.

14. Reattach the cover plate to the dome housing.

15. Using safety wire, attach the dome to a strong

structural ceiling member as follows:

a. Find a strong structural member capable of

supporting the dome. Wrap one end of the

wire around this member and twist the wire

around itself four times to secure.

b. Run the other end of the wire through one

of the holes above the swing out tabs.

Twist the wire around itself four times to

secure.

c. Ensure the wire is taut!

WARNING! Keep the wire as

taut as possible. Do not secure

to any component of a fire

control system.

SPEEDDOME OPTIMA LT INDOOR CAMERA DOME INSTALLATION AND SERVICE GUIDE (8200-0181-01, REV. C)

8 of 14

16. Insert the dome into the hole in the ceiling.

17. Turn each of the two locking screws clockwise

to fully extend the “swing out” mounting clips

and to seat them tightly against the top surface

of the ceiling.

18. Apply power to dome.

Note: When power is applied, the dome

checks its function by performing a homing

routine during which the camera pans and then

either goes to the start point of the “apple peel”

pattern or if powered up once before, to the

last position in memory. Once the camera

stops, the camera is online and is ready to be

controlled.

Also, green, red, and yellow LEDs will light in

various patterns to indicate status. Typically,

you do not need to view these LEDs unless a

failure occurs during or after the routine. See

“Troubleshooting” for an explanation of the

LED patterns.

19. Once the homing routine completes, affix the

bubble to the dome as follows:

a. Place the large hole at the end of the

lanyard over the screw head of the bubble

and pull its end to snap it in place. Loop

the lanyard to the inside of the housing.

b. Center the bubble over the dome housing

and align its tabs with the mating tabs in

the housing.

c. Turn the bubble clockwise until it catches

the tabs and stops.

SPEEDDOME OPTIMA LT INDOOR CAMERA DOME INSTALLATION AND SERVICE GUIDE (8200-0181-01, REV. C)

9 of 14

Troubleshooting

If a failure cannot be easily fixed, send the dome to

a repair center.

No power (no LEDs light).

Check for power coming in from J-box or controller.

Homing routine does not complete.

Green, red, and yellow LEDs are visible through

small holes in the dome housing that surround the

camera yoke. After power up, the LEDs light as

follows:

GREEN

(DS1)

RED

(DS2)

YELLOW

(DS3)

PLD Loading

(approx. 20 sec)

On Off Off

Homing Process Off Blink On

Looking for Network* On Off On

Online Waiting for 1st

Command**

Blink Blink On

* If the dome remains in this state, it cannot locate either the

SensorNet, RS422, or Manchester network.

** The yellow LED remains on until it receives a PTZ movement

command, then goes off. Further PTZ commands will cause

the LED to blink; otherwise, the LED is off.

No video.

1. Check the video cable and its connection to

the dome. If not OK, fix or replace the cable.

2. Check the iris setting. Open iris or set to auto

iris.

3. If the problem cannot be corrected, send the

dome to a repair center.

Video rolls when switching cameras.

Perform V-phase adjustment at the controller.

Contrast or color off.

1. Check the iris setting. Open iris or set to auto

iris.

2. If the problem cannot be corrected, send the

dome to a repair center.

Pan control absent or improper, but other

control OK.

Send the dome to a repair center.

Tilt control absent or improper, but other

control OK.

1. Check tilt belt operation. Fix the belt if

necessary.

2. If the problem cannot be corrected, send the

dome to a repair center.

Zoom, focus, and iris control is absent.

Check the flex cable connecting the camera the

housing. If you see damage, send the dome to a

repair center.

Only some camera control (for example, zoom

and focus works, iris doesn’t).

Send the dome to a repair center.

SPEEDDOME OPTIMA LT INDOOR CAMERA DOME INSTALLATION AND SERVICE GUIDE (8200-0181-01, REV. C)

10 of 14

Parts List for

Authorized Users

The following parts can only be ordered by

authorized users. To become authorized, contact

your sales representative.

General

1 Chassis Assembly, NTSC 0101-0013-01

2 Chassis Assembly, PAL 0101-0013-02

3 Housing Assembly 0404-0009-01

4 Install Kit 0352-0020-01

5 Bubble Assembly, Clear 0100-2458-01

6 Bubble Assembly, Smoked 0100-2458-02

Tilt Assy. 0400-1207-01 (NTSC), -02 (PAL)

7 Base, Tilt 0500-9110-01

8 Gear, Camera Base 0500-9112-01

9 Tilt Upright (2) 0500-9168-01

10 Camera, Hitachi VK-S144,

NTSC

2003-0037-11

11 Camera, Hitachi VK-S144,

PAL

2003-0037-12

12 Timing Belt 2500-0041-01

13 Tilt Motor with Pully 3501-0024-01

14 PCB, Tilt Sensor 0301-1524-01

15 Ribbon Cable, 20mm, Blk 6007-0039-03

Base Assy. 0404-0008-01

16 Base, Pan 0500-9109-01

17 Slip Ring 2100-0006-02

18 Bearing, Pan 2510-0040-01

19 Pan Motor Assy. 0400-1240-01

20 PCB, Dome System 0301-1620-01

1,2

5,6

Tabla de contenidos

Otros manuales de Cámara de seguridad de American Dynamics

American Dynamics

American Dynamics RT3300MC Manual de usuario

American Dynamics

American Dynamics Illustra Flex Series Manual de usuario

American Dynamics

American Dynamics SpeedDome Optima LT Manual de usuario

American Dynamics

American Dynamics SpeedDome Ultra VII Manual de usuario

American Dynamics

American Dynamics ADCI625-P221 Manual de usuario

American Dynamics

American Dynamics ADSDUHOC Manual de usuario

American Dynamics

American Dynamics ADC722WP Manual de usuario

American Dynamics

American Dynamics ADC780 Instrucciones de montaje

American Dynamics

American Dynamics ADC720D Manual de usuario

American Dynamics

American Dynamics SpeedDome Ultra 8 35x Manual de usuario

American Dynamics

American Dynamics SpeedDome Optima LT Manual de usuario

American Dynamics

American Dynamics ADC531 Manual de usuario

American Dynamics

American Dynamics SpeedDome RHODULP-01 Instrucciones de instalación y mantenimiento

American Dynamics

American Dynamics ADC521B Manual de usuario

American Dynamics

American Dynamics ADC 660N Manual de usuario

American Dynamics

American Dynamics Illustra 1MP Manual de usuario

American Dynamics

American Dynamics Discover 600 Series Manual de usuario

American Dynamics

American Dynamics SpeedDome Ultra VI Instrucciones de instalación y mantenimiento

American Dynamics

American Dynamics illustra 600 Instrucciones de funcionamiento originales

American Dynamics

American Dynamics ADCDH Manual de usuario

American Dynamics

American Dynamics ADCA Series Manual de usuario

American Dynamics

American Dynamics ADCA470CAFN Manual de usuario

American Dynamics

American Dynamics VideoEdge IP Indoor Mini-dome 8200-2646-02... Instrucciones de funcionamiento originales

American Dynamics

American Dynamics ADC523PIR Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario