American DJ ScanTron Manual de usuario

American DJ

4295 Charter Street

Los Angeles CA. 90058

www.americandj.com

Revised 8/02

User Instructions

Unpacking:

Thank you for purchasing the ScanTron™ by American

. Every ScanTron™ has been thoroughly tested and has been

shipped in perfect operating condition. Carefully check the shipping

carton for damage that may have occurred during shipping. If the

carton appears to be damaged, carefully inspect your  xture for any

damage and be sure all equipment necessary to operate the unit has

arrived intact. In the event damage has been found or parts are miss-

ing, please contact our toll free customer support number for further

instructions. Please do not return this unit to your dealer without  rst

contacting customer support.

Introduction:

This unit is five channel DMX intelligent scanner that

may be easily converted to an intelligent color changer by removing

the mirror unit. This unit can also run as a stand alone, sound-active

unit, or in a Master/Slave configuration as either a scanner or color

changer. The ScanTron

™

comes with several build in programs and is

best used in multiples of four. When used as a stand alone unit or when

used in multiples linked in a master/slave configuration the optional

IRC/1 controller may be used. The optional controller will access dif-

ferent programs and control a blackout function.

For best results use

fog or special effects smoke to enhance the beams projections.

Customer Support:

American DJ

provides a toll free customer

support line, to provide set up help and to answer any question should

you encounter problems during your set up or initial operation. You

may also visit us on the web at www.americandj.com for any com-

ments or suggestions. Service Hours are Monday through Friday 9:00

a.m. to 5:00 p.m. Paci c Standard Time.

Voice:

(800) 322-6337

Fax:

(323) 582-2610

E-mail:

[email protected]

Warning!

To prevent or reduce the risk of electrical shock or  re, do

not expose this unit to rain or moisture.

Caution!

There are no user serviceable parts inside this unit. Do not

Caution! There are no user serviceable parts inside this unit. Do not Caution!

attempt any repairs yourself, doing so will void your manufactures

warranty. In the unlikely event your unit may require service please

contact your nearest American DJ

dealer.

ScanTron™ General Information

American DJ

- www.americandj.com - ScanTron™ Instruction Manual Page 2

American DJ

- www.americandj.com - ScanTron™ Instruction Manual Page 3

ScanTron™ Halogen Lamp Warning

This fixture is fitted with halogen lamps which are

highly susceptible to damage if improperly han-

dled. Never touch the lamps with your bare fin-

gers as the oil from your hands will shorten lamp

life. Also, never move the fixture until the lamps

have had ample time to cool. Remember, lamps

are not covered under warranty conditions.

•

Micro-Stepping Motors for Smooth Color and Gobo Transitions

•

DMX-512 Protocol Compatible (Uses Five DMX Channels)

•

14 Gobo Patterns Plus Spot/11 Colors Plus White

•

Master/Slave Operation

•

Internal Microphone with Volume Sensitivity Knob

•

Removable Head for Color Changer Operation

•

Variable Speed Strobe Function

•

Optional IRC/1 Remote Controller

ScanTron™ Features

The ScanTron™ carries a one year limited warranty. Please fill out the

enclosed warranty card to validate your purchase. All returned service

items whether under warranty or not, must be freight pre-paid and

accompany a return authorization (R.A.) number. The R.A. number

must be clearly written on the outside of the return package. A brief

description of the problem as well as the R.A. number must also be

written down on a piece of paper included in the shipping carton. If

the unit is under warranty, you must provide a copy of your proof of

purchase invoice. You may obtain a R.A. number by contacting our

customer support team on our toll free customer support number. All

packages returned to the service department not displaying a R.A.

number on the outside of the package will be returned to the shipper.

ScanTron™ Product Registration

•

To reduce the risk of electrical shock or  re, do not expose this unit

rain or moisture

•

Do not spill water or other liquids into or on to your unit.

•

Be sure that the local power outlet match that of the required volt-

age for your unit.

•

Do not attempt to operate this unit if the power cord has been

frayed or broken.

•

Do not attempt to remove or break off the ground prong from

the electrical cord. This prong is used to reduce the risk of electrical

shock and  re in case of an internal short.

•

Disconnect from main power before making any type of connection.

•

Do not remove the cover under any conditions. There are no user

serviceable parts inside.

•

Never operate this unit when it’s cover is removed.

•

Never plug this unit in to a dimmer pack

•

Always be sure to mount this unit in an area that will allow proper

ventilation. Allow about 6” (15cm) between this device and a wall.

•

Do not attempt to operate this unit, if it becomes damaged.

•

This unit is intended for indoor use only, use of this product out-

doors voids all warranties.

•

During long periods of non-use, disconnect the unit’s main power.

•

Always mount this unit in safe and stable matter.

•

Power-supply cords should be routed so that they are not likely to

be walked on or pinched by items placed upon or against them,

paying particular attention to cords at plugs, convenience recep-

tacles, and the point where they exit from the appliance.

• Cleaning -The fixture should be cleaned only as recommended by

the manufacturer. See page 7 for cleaning details.

•

Heat -The appliance should be situated away from heat sources

such as radiators, heat registers, stoves, or other appliances

(including amplifiers) that produce heat.

•

The fixture should be serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the appliance.

C. The appliance has been exposed to rain or water.

D. The appliance does not appear to operate normally or exhibits a

marked change in performance.

ScanTron™ Safety Precautions

American DJ

- www.americandj.com - ScanTron™ Instruction Manual Page 4

To optimize the performance of this product, please read these operating

instructions carefully to familiarize yourself with the basic operations of

this unit. These instructions contain important safety information regard-

ing the use and maintenance of this unit. Please keep this manual with

the unit, for future reference.

ScanTron™ General Instructions

American DJ

- www.americandj.com - ScanTron™ Instruction Manual Page 6

American DJ

- www.americandj.com - ScanTron™ Instruction Manual Page 5

ScanTron™ Controls and Functions

REAR

FRONT

Thumb Screw -

This thumb screw holds the lamp socket assem-

bly cover (16) into place.

Audio Sensitivity Knob -

This adjust audio sensitivity of the

INTERNAL MICROPHONE (3)

. Turning the sensitivity knob in the

clockwise direction will increase the sensitivity to sound. Turning the

knob in the counter clockwise direction will decrease the  xture’s sen-

sitivity to sound.

Dip Switches -

These switches serve two functions. In DMX mode

each switch corresponds to a speci c value based on binary code.

See page 7 for a detailed explanation of DMX binary code. When the

unit is operating in master/slave mode the pan and tilt movements may

ScanTron™ Controls and Functions

be inverted by moving dip switch 10 to the “on” position. All other dip

switches have no function in master/slave mode.

Microphone -

This microphone receives external low frequencies

to trigger the unit in Sound-Active and Master/Slave mode.

IRC/1 Controller Jack -

This jack is for use with the optional IRC/1

controller only.

Do not attempt to connect an audio signal to this jack,

this will damage the PC board and void your manufactures warranty!

XLR Output Jack -

This jack is used to transmit the incoming

DMX

signal to another DMX  xture, or transmit a Master/Slave signal

to the nest ScanTron™ in the chain. For best results in DMX or Master/

Slave mode terminate this jack if it is the last unit in the chain. See

“Terminator” on page 7.

XLR Input Jack -

This jack is used to accept an incoming DMX

signal or Master/Slave signal.

Fuse Holder -

This housing stores the 5 amp (3 amp 220v) protec-

tive fuse.

Power Cord -

Connect only to a matching power outlet. Never

use

this  xture is the ground prong has been removed or broken off.

10. Mirror -

This is a highly re ective surface mirror speci cally

designed to optimize and enhance beam output. Never use glass

cleaner that contain ammonia to clean the surface of the mirror (such

as Windex).

11.

Lens -

This is a fully focusing high quality lens. Focus the lens by

manually turning the lens in a clockwise or counter-clockwise direc-

tion.

12. Mirror Interface -

This connection is used to create an interface

between the mirror head and the unit body. Disconnect this interface

when the unit is going to be used as a color changer with the mirror

piece removed.

13.

Lamp Socket Assembly -

This assembly holds a LL-ELC (24v/

250w) lamp.

14.

Lamp Socket Assembly Plate -

This plate is used to protect and

accesses the lamp socket assembly.

Operating Modes:

•

Stand alone mode -

The unit will react to sound, chasing through

the built-in programs. You can also use the optional IRC/1 Remote

Control to blackout and other functions.

• Master/Slave mode -

You can daisy chain up to 16 units together

to get a synchronized light show that will react to sound chasing

through several built in programs.You can also use the optional IRC/1

Remote Control to blackout and other functions.

•

DMX control mode -

This function will allow you to control each

individual fixtures traits with a standard DMX--512 controller such as

the American DJ Show Designer.

™

•

Color Changer -

By removing the mirrored head this unit will func-

tion as a color change in all the preeceding modes. See page 14.

Universal DMX Control:

This function allows you to use a univer-

sal DMX-

512

controller such

as the American DJ

DMX Operator™

or Show Designer™ to control mirror movement, the color wheel, the

gobo wheel, and the shutter (strobe). A DMX controller allows you to

create unique programs tailored to your individual needs.

Special

Note:

Because these units are designed to automatically go in to

sound-active mode when they do not sense a DMX signal, these units

may activate when your DMX controller is turned off. To avoid this

problem leave your DMX controller on when the lights are powered on

and be sure the sound

sensitivity knob is always turned down

(coun-

ter-clockwise) when running these units in DMX mode.

The ScanTron™ uses five DMX channels. Channel 1 controls pan,

channel 2 controls tilt, channel 3 controls color channel 4 controls

gobo wheel, and channel 5 controls the strobe function. See page

14 for detailed description of the DMX traits.

To control your fixture in DMX mode, follow the set-up procedures

on pages 5 - 7 as well as the set-up specifications that are includ-

ed with your DMX controller.

Use the controller’s faders to control the various DMX fixture traits.

This will allow you to create your own programs.

When using a DMX controller and setting up for DMX operation

follow the dip switch settings on page 15.

For longer cable runs (more than a 100 feet) use a terminator on

the last fixture.

ScanTron™ Operation

American DJ

- www.americandj.com - ScanTron™ Instruction Manual Page 8

American DJ

- www.americandj.com - ScanTron™ Instruction Manual Page 7

ScanTron™ Operation

For help operating in DMX mode consult the manual included

with your DMX controller.

Stand-Alone Operation (Sound Active):

This mode allows a

single unit to run to the beat of the music. Only use this mode when

running a single unit, or when running several units as individuals.

This unit is automatically designed to go into sound-active mode

when it does not sense a DMX signal. The unit will react to the

low frequencies of music via the internal microphone. You may

invert the pan and tilt functions by  ipping dip switch 10 to the

“on” position.

Adjust the audio sensitivity knob on the bottom of the unit to make

the unit more or less sensitive to sound.

Turning the sensitivity knob

in the clockwise direction will increase the sensitivity, turning the

knob in the counter-clockwise direction will decrease the  xture’s

sensitivity to sound.

The optional

IRC/1 Controller

may be used with this mode to

control blackout, slow scan, and strobe functions.

Master-Slave Operation (Sound Active):

This function will allow

you to link up to 4 units together and operate without a controller. The

units will be sound activated. In Master-Slave operation one unit will

act as the controlling unit and the others will react to the controlling

units programs. Any unit can act as a Master or as a Slave.

Using standard XLR microphone cables, daisy chain your units

together via the XLR connector on the rear of the units. Remem-

ber the Male XLR connector is the input and the Female XLR

connector is the output. The  rst unit in the chain (master) will use

the female XLR connector only - The last unit in the chain will use

the male XLR connector only. For longer cable runs we suggest a

terminator at the last fixture.

Follow the chart on page 14 for proper unit dip switch settings.

The optional

IRC/1 Controller

may be used with in this opera-

tion for blackout, slow scan, and strobe function.

After all the units settings have been set and are plugged in,

adjust the sensitivity knob on the rear of the master unit to make

them react to sound.

Note: In Stand-Alone and Master-Slave operation the units will black-

out to conserve lamp life when a sound source is not received.

sound activation or in this case pan/tilt inversion.

Each dip switch has a preset value. A specific DMX address is set by

combining the dip switches that sum your desired value. For exam-

ple: To achieve a DMX address of 21, combine dip switches 1, 3, and

5. Sense dip switch 1 has a value of 1, dip switch 3 has a value of 4,

and dip switch 5 has a value of 16, the combination of the create a

DMX value of 21.

Set DMX address 21:

Set DMX address 201:

Dip-switches #

1 = 1

Dip-switches #

1 = 1

3 = 4

4 = 8

5 = 16

7 = 64

= 21

8 = 128

= 201

Data Cable (DMX Cable) Requirements (For DMX and Master/Slave

Operation):

The ScanTron™ can be controlled via DMX-512 protocol.

The ScanTron™ is a  ve channel DMX unit. The DMX address is set

on the bottom panel of the ScanTron.™ Your unit and your DMX con-

troller require a standard 3-pin XLR connector for

data input and data output (Figure 1). If you are

making your own cables, be sure to use standard

two conductor shielded cable (This cable may be

purchased at almost all pro sound and lighting

stores). Your cables should be made with a male

and female XLR connector on either end of the

cable. Also remember that DMX cable must be

daisy chained and can not be split.

Figure 1

American DJ

- www.americandj.com - ScanTron™ Instruction Manual Page 10

American DJ

- www.americandj.com - ScanTron™ Instruction Manual Page 9

Power Supply:

Before plugging your unit in, be sure the source volt-

age in your area matches the required voltage for your American DJ

ScanTron.™ The American DJ

ScanTron

™

is available in a 120v and

220v version. Because line voltage may vary from venue to venue,

you should be sure your unit voltages matches the wall outlet voltage

before attempting to operate you  xture.

DMX-512:

DMX is short for Digital Multiplex. This is a universal pro-

tocol used as a form of communication between intelligent fixtures

and controllers.

A DMX controller sends DMX data instructions from

the controller to the fixture. DMX data is sent as serial data that trav-

els from fixture to fixture via the DATA “IN” and DATA “OUT” XLR ter-

minals located on all DMX fixtures (most controllers only have a DATA

“OUT” terminal).

DMX Linking:

DMX is a language allowing all makes and models of

different manufactures to be linked together and operate from a sin-

gle controller, as long as all  xtures and the controller are DMX com-

pliant.

To ensure proper DMX data transmission, when using several

DMX fixtures try to use the shortest cable path possible. The order

in which fixtures are connected in a DMX line does not influence the

DMX addressing. For example; a fixture assigned a DMX address of 1

may be placed anywhere in a DMX line, at the beginning, at the end,

or anywhere in the middle. When a fixture is assigned a DMX address

of 1, the DMX controller knows to send DATA assigned to address 1

to that unit, no matter where it is located in the DMX chain.

Dip-switches in DMX mode:

This unit uses dip switches to assign a

DMX address. Each dip switch represents a binary value.

Dip Switch 1 address equals 1

Dip Switch 2 address equals 2

Dip Switch 3 address equals 4

Dip Switch 4 address equals 8

Dip Switch 5 address equals 16

Dip Switch 6 address equals 32

Dip Switch 7 address equals 64

Dip Switch 8 address equals 128

Dip Switch 9 address equals 256

Dip Switch 10 - Some unit omit dip switch 10, when a unit does

included dip switch 10 it is usually used for special functions such as

ScanTron™ Set Up ScanTron™ Set Up

128

256

DMX CHANNEL

Notice:

Be sure to follow  gures two and three when making your own

cables. Do not use the ground lug on the XLR connector. Do not con-

nect the cable’s shield conductor to the ground lug or allow the shield

conductor to come in contact with the XLR’s outer casing. Grounding

the shield could cause a short circuit and erratic behavior.

DMX512 IN

3-PIN XLR

DMX +

DMX -

COMMO

DMX512 OUT

3-PIN XLR

Figure 2

ScanTron™ Fuse & Lamp Replacement

American DJ

- www.americandj.com - ScanTron™ Instruction Manual Page 11

American DJ

- www.americandj.com - ScanTron™ Instruction Manual Page 12

Caution:

Always replace with the exact same type lamp and fuse,

unless otherwise specified by an authorized American

service

technician. Replacing with anything other than the specified part can

damage your unit and will void your manufactures warranty.

Warning:

If you continue to blow lamps or fuses, STOP using the

unit. Contact customer support for further instructions, you may have

to return the unit for servicing. Continuing to use the unit may cause

serious damage.

Lamp Replacement:

Caution! Never attempt to change the lamp

while the fixture is plugged in. Always disconnect the main power

and allow the unit ample time to cool before attempting to replace the

lamp. Lamp replacement has been made simple by incorporating the

use of a flip-up front cover that is retained by thumb screws.

Be sure to follow the proper handling procedures that deal with

halogen lamps.

Remove the thumb screw on the rear of the unit that holds the

lamp socket assembly cover in place.

After removing the thumb screw, slide out the cove from the rear

of the unit to expose the lamp socket assembly.

Carefully remove the old lamp and discard it in the trash.

Replace the lamp with an exact match and reassemble in reverse

order.

Fuse Replacement:

Disconnect the unit from the main power supply.

Insert a standard flat head screw driver in to the fuse holder housing.

Turn the screwdriver in counter-clockwise direction to remove the fuse

holder. Remove the old fuse and discard it, replace the fuse with the

same type. Insert the fuse back into it’s housing.

ScanTron™ Set Up

Figure 3

1 Ground

XLR Male Socket

XLR Pin Con guration

3 Hot

2 Cold

3 Hot

XLR Female Socket

Pin 3 = Data True (positive)

Pin 2 = Data Compliment (negative)

Pin 1 = Ground

Special Note: Line Termination.

When longer runs of cable are

used, you may need to use a terminator on the last unit to avoid erratic

behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is con-

nected between pins 2 and 3 of a male XLR connector (DATA + and

DATA -). This unit is inserted in the female XLR connector of the last

unit in your daisy chain to terminate the line. Using a cable terminator

(ADJ part number Z-DMX/T) will decrease the possibilities of erratic

behavior.

rmination

educes

signal

rrors

and

avoids

signal

transmission

problem

and

interference.

always

advisable

connect

DMX

terminal,

(Resistance

120

Ohm

1/4

between

(DMX-)

and

(DMX

the

last

fixture.

Figure 4

5-Pin XLR DMX Connectors.

Some manufactures use 5-pin XLR

connectors for DATA transmission in place of 3-pin. 5-pin XLR  xtures

may be implemented in a 3-pin XLR DMX line. When inserting stan-

dard 5-pin XLR connectors in to a 3-pin line a cable adaptor must be

used, these adaptors are readily available at most electric stores. The

chart below details a proper cable conversion.

Conductor

5-Pin XLR Male (In)

3-Pin XLR Female (Out)

Pin 1

Pin 5 - Do Not Use

Pin 4 - Do Not Use

Pin 3

Pin 2

Pin 1

Pin 3

Pin 2

Not Used

Data True (+ signal)

Data Compliment (- signal)

Ground/Shield

3-Pin XLR to 5-Pin XLR Conversion

Thumb Screws

Lamp Cover

Lamp Socket

Assembly

American DJ

- www.americandj.com - ScanTron™ Instruction Manual Page 14

ScanTron™ Cleaning

ScanTron™ Trouble Shooting

Fixture Cleaning:

Due to fog residue, smoke, and dust cleaning the

internal and external optical lenses and mirror should be carried out

periodically to optimize light output. Cleaning frequency depends on

the environment in which the fixture operates (I.e. smoke, fog residue,

dust, dew). In heavy club use we recommend cleaning on a monthly

basis. Periodic cleaning will ensure longevity, and crisp output.

Use normal glass cleaner and a soft cloth to wipe down the out-

side casing.

Use a brush to wipe down the cooling vents and fan grill.

Clean the external optics and mirror with glass cleaner and a soft

cloth every 20 days.

Clean the internal optics with glass cleaner and a soft cloth every

30-60 days.

Always be sure to dry all parts completely before plugging the unit

back in.

Trouble Shooting:

Listed below are a few common problems that

you may encounter, with solutions.

No light output from the unit;

Be sure you have connected your unit into a standard 120v wall

outlet.

Be sure the external fuse has not blown. The fuse is located on

the bottom panel of the unit.

Remove the lamp cover and be sure the lamp is seated in its

socket properly. Occasionally lamps become loose during ship-

ping be sure the lamp is push in to its socket all the way.

Be sure the fuse holder is completely and properly seated.

Unit does not respond to sound;

Low frequencies (bass) should cause the unit to react to sound.

Tapping on the microphone, quiet or high pitched sounds may

not activate the unit.

Be sure the

SENSITIVITY KNOB (5)

is not set to the minimum

position (full counter-clockwise).

American DJ

- www.americandj.com - ScanTron™ Instruction Manual Page 13

ScanTron™ Color Changer Conversion

ScanTron™ DMX Traits

This chart below details the DMX traits. The individual trait can only

be accessed an universal DMX controller.

The icons below detail the gobo pattern as well as their placement on

the gobo wheel, starting with 1 on the left and 15 on the right.

DMX512 CONFIGURATION

CHANNEL 2

TILTPAN

FLAT FLATBARREL BARREL

Stopped

CHANNEL 1 CHANNEL 3

White

255

110

121

Red

Blue

Green

Yellow

Amber

Pink

Lt. Blue

Purple

Lt. Green

Orange

Magenta

COLOR

128

Slow

Fast

Gobo 9

Gobo 7

Gobo 5

Gobo 3

Blackout

Gobo 1

Gobo 11

Gobo 13

Gobo 14

Gobo 12

Gobo 10

Gobo 2

Gobo 4

Gobo 6

Gobo 8

Open

CHANNEL 4

GOBO

104

112

120

255 Fast

128

Slow

CHANNEL 5

SHUTTER

255

Stopped

Gobo+Color

Color

Gobo

174

The ScanTron™ is designed with a remov-

able mirror head. When the head is removed

the unit can be used as a color changer with

gobo patterns. The unit will function normally

in all opperating modes with the exception

of mirror movements. To remove the head;

1 Disconnect the mirror interface cable, 2

Unscrew the three large thumb-screws sur-

rounding the output lenses that secure the

head assembly to the body. 3 Gently pull the

up and away from the output lens.

Mirror

Interface

Thumb-

Screws

American DJ

- www.americandj.com - ScanTron™ Instruction Manual Page 15

X = OFF

O = ON

#1 #2 #3 #4 #5

3 64 96 128 160 192 224 256 288 320 352 384 416 448 480

1 33 65 97 129 161 193 225 257 289 321 353 385 417 449 481

2 34 66 98 130 162 194 226 258 290 322 354 386 418 450 482

3 35 67 99 131 163 195 227 259 291 323 355 387 419 451 483

4 36 68 100 132 164 196 228 260 292 324 356 388 420 452 484

5 37 69 101 133 165 197 229 261 293 325 357 389 421 453 485

6 38 70 102 134 166 198 230 262 294 326 358 390 422 454 486

7 39 71 103 135 167 199 231 263 295 327 359 391 423 455 487

8 40 72 104 136 168 200 232 264 296 328 360 392 424 456 488

9 41 73 105 137 169 201 233 265 297 329 361 393 425 457 489

10 42 74 106 138 170 202 234 266 298 330 362 394 426 458 490

11 43 75 107 139 171 203 235 267 299 331 363 395 427 459 491

12 44 76 108 140 172 204 236 268 300 332 364 396 428 460 492

13 45 77 109 141 173 205 237 269 301 333 365 397 429 461 493

14 46 78 110 142 174 206 238 270 302 334 366 398 430 462 494

15 47 79 111 143 175 207 239 271 303 335 367 399 431 463 495

16 48 80 112 144 176 208 240 272 304 336 368 400 432 464 496

17 49 81 113 145 177 209 241 273 305 337 369 401 433 465 497

18 50 82 114 146 178 210 242 274 306 338 370 402 434 466 498

19 51 83 115 147 179 211 243 275 307 339 371 403 435 467 499

20 52 84 116 148 180 212 244 276 308 340 372 404 436 468 500

21 53 85 117 149 181 213 245 277 309 341 373 405 437 469 501

22 54 86 118 150 182 214 246 278 310 342 374 406 438 470 502

23 55 87 119 151 183 215 247 279 311 343 375 407 439 471 503

24 56 88 120 152 184 216 248 280 312 344 376 408 440 472 504

25 57 89 121 153 185 217 249 281 313 345 377 409 441 473 505

26 58 90 122 154 186 218 250 282 314 346 378 410 442 474 506

27 59 91 123 155 187 219 251 283 315 347 379 411 443 475 507

28 60 92 124 156 188 220 252 284 316 348 380 412 444 476 508

29 61 93 125 157 189 221 253 285 317 349 381 413 445 477 509

30 62 94 126 158 190 222 254 286 318 350 382 414 446 478 510

31 63 95 127 159 191 223 255 287 319 351 383 415 447 479 511

DMX DIP Switch Settings

DIP SWITCHES

OOO OOX OO OXX X X X X X

OOO OOOO OX X XXX X X X

OXO XOO XX OOX X X XOO

XOX XOO OX OXX O X O X O

OXXXX

X O X O X

O X X O X

XXXOX

OOOX X

X O O X X

XXOXX

O O X X X

XOXXX

O X O X X

X OOOX

O O X X O

XOXXO

OXXXO

XXXXO

OOOOX

OX OOX

X X O O X

OOX OX

XXXOO

OOOOO

X OOOO

OX OOO

X X O O O

OOX OO

X O X O O

O X X O O

OOOX O

X O O X O

O X O X O

XXOXO

XXXXX

DMX Address

DMX Address Quick Reference Chart

Dip Switch Position

The center numbers of this chart (1-511) represent a DMX address. The "X"'s

and "O"'s along the top and side of the chart represent dip switch poistion ("X"

for off and "O" for on). Find your desired DMX address from the center chart.

Identify the position for dip switches 1-5 from the chart on the left and dip

switches 6-9 from the chart on the top. Adjust the dip switches on your fixture

to match the position settings of the chart. For fixtures with 10 dip switches;

dip switch 10 is reserved for special functions.

This chart list the DMX dip switch setting for DMX address 1 through

511. Follow the instructions below to configure fixture dip switches

with your desired DMX address.

ScanTron™ DMX Dip Switch Chart

©American DJ®

A Division of the American DJ® Group of Companies

World Headquarters:

4295 Charter Street Los Angeles, CA 90058 USA

Tel: 323-582-2650 Fax: 323-582-2610

Web: www.americandj.com E-mail: [email protected]

Model:

ScanTron™

Voltage*:

120v/60Hz or 220v/50Hz

Lamp:

LL-ELC, 24v/250w

Dimensions:

19.75”(H) x 7.5”(W) x 6”(D)

500mm x 200mm x 155mm

Colors:

11 Plus White

Gobos:

14, Plus Spot

Weight:

25 Lbs.

Fuse:

5A (120v) / 3A (220v)

Duty Cycle:

None

DMX:

5 Channels

Sound Active:

Yes

Working Position:

Any Safe, Secure Position

Warranty:

1 Year (365 days)

*Voltage is preset at the factory and is not user selectable

Please Note:

Speci cations and improvements in the design

of this unit and this manual are subject to change without any

prior written notice.

ScanTron™ DMX Dip Switch Chart

Tabla de contenidos

Otros manuales de Luminaria de American DJ

American DJ

American DJ Profile Panel RGB Manual de usuario

American DJ

American DJ Jelly GO Par64 Manual de usuario

American DJ

American DJ Vizi Wash LED 108 Manual de usuario

American DJ

American DJ Double Roller Manual de usuario

American DJ

American DJ Accu Scan 250 Manual de usuario

American DJ

American DJ INNO COLOR BEAM QUAD 7 Manual de usuario

American DJ

American DJ Flat Par QWH12X Manual de usuario

American DJ

American DJ Mega Pixel Arch Manual de usuario

American DJ

American DJ Arcbeam 150 Manual de usuario

American DJ

American DJ ActivePod Manual de usuario

American DJ

American DJ WIFLY BAR RGBA Manual de usuario

American DJ

American DJ ColorPod Manual de usuario

American DJ

American DJ XP3 Manual de usuario

American DJ

American DJ Colorbar 39 Manual de usuario

American DJ

American DJ Accu UFO PRO Manual de usuario

American DJ

American DJ Globe Color Manual de usuario

American DJ

American DJ VORTEX/G Manual de usuario

American DJ

American DJ Mini Starball II Manual de usuario

American DJ

American DJ X-Move LED 25R Manual de usuario

American DJ

American DJ X-Treme Manual de usuario

American DJ

American DJ Flash Duo VS Manual de usuario

American DJ

American DJ Reflex 300 Manual de usuario

American DJ

American DJ Vizi Spot LED PRO Manual de usuario

American DJ

American DJ Fantasy 250 Manual de usuario

Manuales populares de Luminaria de otras marcas

Emos

Emos CLASSIC ZY1431T Manual de usuario

Westinghouse

Westinghouse Outdoor Lighting Fixture Manual de usuario

Hedler

Hedler C 12 silent Manual de usuario

Blizzard Lighting

Blizzard Lighting Puck: CSI Manual de usuario

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Manual de usuario

Lightmaxx

Lightmaxx Shaft 5R Manual de usuario

Triarch

Triarch 31083 Manual de usuario

Philips

Philips 32614 Series Manual de usuario

IKEA

IKEA TIVED Manual de usuario

Lightolier

Lightolier LP200 Manual de usuario

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Manual de usuario

Martin

Martin MAC 250 Krypton Manual de usuario

Cooper Lighting

Cooper Lighting Halo L3232E Manual de usuario

Stageline

Stageline ODW-2410RGBW Manual de usuario

Light Sky

Light Sky Tornado Series Manual de usuario

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Manual de usuario

Lightolier

Lightolier Lytespan 83ED17S Manual de usuario

Lightolier

Lightolier Calculite CS8226 Manual de usuario