American Audio V3000/V2000 Manual de usuario

PROFESSIONAL

POWER AMPLIFIERS

User Instructions

channel 1 channel 2

V3000

American DJ SIG20 1010 20

SIG 55CLIP

CLIP PROTECT PROTECT

POWER

LIMITER LIMITER

ON ON

PROformer Series Professional Stereo Amplifier

professional products designed for

installations and the working dj.

V3000 / V2000 MK II Power Amplifier Instructions

©American AUDIO Los Angeles, CA 90058 USA

channel 1 channel 2

American DJ SIG20 1010 20

SIG 55CLIP

CLIP PROTECT PROTECT

POWER

LIMITER LIMITER

ON ON

PROformer Series Professional Stereo Amplifier

For optimum performance and reliability DO

NOT PRESENT THE AMPLIFIER WITH A

SPEAKER LOAD OF LESS THAN 2 OHMS.

OR ANY COMBINATION OF SPEAKERS THAT

TOGETHER ARE LESS THAN 2 OHMS PER SIDE!

• Using one speaker, it must be rated at

2 ohms minimum.

• Using two speakers, they must be rated

each at 4 ohms minimum.

• Using three speakers, they must be rated

each at 8 ohms minimum.

Pour assurer la Fiabilte et obtenit une per-

formance optimale, ne soumette jamais

l’amplificateur a une charge d’impedance

totale inferieure a 2 ohms, ni avec un H.P. ni en com

binasion des H.P.

AVEC un H.P., il Faut une charge d’impedance

minimum de 2 ohms.

AVEC deux H.P., il Faut pour chaoun une charge

d’impedance minimum de 4 ohms.

AVEC trois H.P. il Faut pour chaon une churge

d’impedance minimum de 8 ohms.

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE THE COVER RACK.

THERE ARE NO USER SERVICEABLE PARTS

INSIDE. REFER SERVICE TO YOUR

AUTHORIZED AMERICAN DJ AUDIO DEALER.

The lightning flash with an arrow triangular

symbol is intended to alert the user to the

presence of uninsulated “dangerous volt-

age” within the products enclosure, and may

be of sufficient magnitude to constitute a

risk of electric shock.

The exclamation point triangular symbol is

intended to alert the user to the presence of

important operating and maintenance (ser-

vicing) instructions in the user manual

accompanying the CD player.

CAUTION

Do not open -

risk of electric shock

Front Panel...............................................3

Rear Panel................................................3

Application Diagrams...........................3,4,5

Operating Voltage.....................................5

Inputs........................................................6

Outputs.....................................................6

Limiter.......................................................6

Low-Cut Filter............................................6

Gain Controls............................................7

LED Indicators..........................................7

Protect Indicators.......................................7

Protection..................................................7

Specifications............................................8

Contents:

Page 2 • American AUDIO V3000 / V2000 MK II Power Amplifier Instructions

1: Power Switch

2: Channel 1 gain controls

3: Channel 2 gain controls

4: Power ON indicator

5: Channel 1 indicators

6: Channel 2 indicators

7: Channel 1 protect indicators

8: Channel 2 protect indicators

9: Channel 1 clip indicator

10: Channel 2 clip indicator

11: Channel 1 limiter switch

12: Channel 2 limiter switch

channel 1 channel 2

V3000

American DJ SIG20 1010 20

SIG 55CLIP

CLIP PROTECT PROTECT

POWER

LIMITER LIMITER

ON ON

PROformer Series Professional Stereo Amplifier

410

11 12

95 8

1234

FUSE

STEREO BRIDGE

AMP MODE

FREQUENCY

SUB

WOOF SUB

WOOF

INPUT

THRU CAUTION

MINIMUM LOAD IMPEDANCE

2 OHM PER CHANNEL

4 OHM BRIDGE

LIFT

GROUND

NORMAL NORMAL

INPUT

BAL.

1500

WATTS

HOT

COLD

GND

13: Channel 1 XLR input

14: Channel 1 TRS input

15: Channel 2 TRS input

16: Channel 2 XLR input

17: Channel 1 subwoof on/off switch (V3000 ONLY)

18: Channel 1 subwoof frequency adj. (V3000 ONLY)

19: Channel 1 subwoof on/off switch (V3000 ONLY)

20: Channel 1 subwoof frequency adj. (V3000 ONLY)

21: Channel 1 input THRU jack

22: Channel 2 input THRU jack

23: Fuse holder

24: AC cord outlet

25: Amplifier mode switch

26: Ground lift switch

27: Channel 1 output jack

28: Channel 2 output jack

29: Function settings dip switch

1516

262728

1234

+++

FUSE

STEREO BRIDGE

AMP MODE

FREQUENCY

SUB

WOOF SUB

WOOF

INPUT

THRU CAUTION

MINIMUM LOAD IMPEDANCE

2 OHM PER CHANNEL

4 OHM BRIDGE

LIFT

GROUND

NORMAL NORMAL

INPUT

BAL.

1500

WATTS

HOT

COLD

GND

STEREO (Typical Settings) IN IN

KEEP FAN

GATES CLEAN!

KEEP FAN

GATES CLEAN!

DO NOT EXCEED

2 OHM MINIMUM

PER CHANNEL

DO NOT EXCEED

2 OHM MINIMUM

PER CHANNEL

Page 3 • American AUDIO V3000 / V2000 MK II Power Amplifier Instructions

BRIDGE MONO (Typical Settings)

STEREO SUBWOOF

ONE NORMAL / ONE SUBWOOF (BI-AMP)

1234

+++

FUSE

STEREO BRIDGE

AMP MODE

FREQUENCY

SUB

WOOF SUB

WOOF

INPUT

THRU CAUTION

MINIMUM LOAD IMPEDANCE

2 OHM PER CHANNEL

4 OHM BRIDGE

LIFT

GROUND

NORMAL NORMAL

INPUT

BAL.

1500

WATTS

HOT

COLD

GND

1234

+++

FUSE

STEREO BRIDGE

AMP MODE

FREQUENCY

SUB

WOOF SUB

WOOF

INPUT

THRU CAUTION

MINIMUM LOAD IMPEDANCE

2 OHM PER CHANNEL

4 OHM BRIDGE

LIFT

GROUND

NORMAL NORMAL

INPUT

BAL.

1500

WATTS

HOT

COLD

GND

1234

+++

FUSE

STEREO BRIDGE

AMP MODE

FREQUENCY

SUB

WOOF SUB

WOOF

INPUT

THRU CAUTION

MINIMUM LOAD IMPEDANCE

2 OHM PER CHANNEL

4 OHM BRIDGE

LIFT

GROUND

NORMAL NORMAL

INPUT

BAL.

1500

WATTS

HOT

COLD

GND

TO NORMAL TO BRIDGE

IN IN

SUBWOOF SUBWOOF

TO STEREO

TO SUBWOOF TO SUBWOOF

SUBWOOF

TO STEREO

TO NORMAL

TO SUBWOOF IN IN

DO NOT EXCEED

4 OHM MINIMUM

2 OHM

MINIMUM 2 OHM

MINIMUM

2 OHM

MINIMUM

2 OHM

MINIMUM

Page 4 • American AUDIO V3000 / V2000 MK II Power Amplifier Instructions

SUBWOOFER (V3000 ONLY)

The subwoofer can be operated in stereo or bridge mono, set the switch to subwoofer position

depending on your application, select the frequency from 20 Hz to 200 Hz via variable frequency

selector.

AMP MODE (STEREO/BRIDGE)

The Amplifier mode should be configured before operation, if you want to change it during perfor-

mance, you must decrease the gain controls to protect the speakers from any popping noise.

THRU

Thru will allow the user to daisy-chain one amplifiers signal input into another amplifier. Plug the

signal source outputs into the first amplifier’s input, patch from the amplifier’s THRU jacks to the

next amplifier’s input, and so on, daisy-chaining as many amplifiers as there is no excessive level

loss. Is not affected by crossover setting.

GROUND LIFT SWITCH

Applying or lifting the ground switch will change level for background noise and hum, if the noise

level remains the same in either position, better to keep the ground lift switch in the ground position.

This will eliminate 60Hz cycle Hum that is sometimes induced when mounting several units in the

same rack.

BRIDGE SUBWOOF (V3000 ONLY)

1234

+++

FUSE

STEREO BRIDGE

AMP MODE

FREQUENCY

SUB

WOOF SUB

WOOF

INPUT

THRU CAUTION

MINIMUM LOAD IMPEDANCE

2 OHM PER CHANNEL

4 OHM BRIDGE

LIFT

GROUND

NORMAL NORMAL

INPUT

BAL.

1500

WATTS

HOT

COLD

GND

SUBWOOF

XTO SUBWOOF TO BRIDGE

OPERATING VOLTAGE (AC mains)

The serial number label indicates the correct AC main voltage. Connecting to the wrong voltage is

dangerous and may damage the amplifier.

4 OHM

MINIMUM

Page 5 • American AUDIO V3000 / V2000 MK II Power Amplifier Instructions

•BALANCED

•SYMETRIQUE

•SYMMETRISCHE

•BALANCEADO

GROUND

INVERTING INPUT - •UNBALANCED

•ASYMETRIQUE

•UNSYMMETRISCHE

•UNBALANCEADO

NON-INVERTING INPUT +

GROUND

NON-INVERTING INPUT +

INPUTS

OUTPUTS (Banana Jack Connection)

Strip back insulation 13-mm. Insert wire fully, tighten barrel.

13mm

1/2”

LIMITER

The limiter has a fixed threshold and will prevent continuous clipping. Below clipping, and during

short clips on peaks, the limiter does not act on the audio signal. The limiter for either channel can

be disabled independently using the slide switch on the front panel.

LOW CUT FILTER

The low-cut filter removes ultra-low frequency information from the audio signal

that could damage or cause distortion in a loud speaker system. The dip switch

on the rear panel allows you to enable or disable the filter independently for

either Channel, as well as set it for either a 50Hz or 30 Hz cut-off. Always use

the 50 Hz filter setting if you are using the amplifier to drive a distributed line system (also known as

a constant-voltage line, 70 volt line, etc.)

12 3 4

CH. 1 CH.2

1 Low 3ON=30Hz

Cut Filter OFF=50Hz

2ON=30Hz 4 Low Cut

OFF=50Hz Filter

OFF

Two input connector, XLR jack for balance and 6.3mm (1/4”) TRS jack for unbalance.

Page 6 • American AUDIO V3000 / V2000 MK II Power Amplifier Instructions

OPERATION

CONFIGURING THE AMPLIFIER

A 4-position dip switch on the rear panel allows you to configure certain amplifier characteristics.

A diagram on the rear panel shows the individual switch functions and settings..

LOW-CUT FILTER: Setting position 1 to “ON” enables the low-cut

filter on channel 1 and “OFF” disables it. Position 4 does the same

for channel 2.

LOW-CUT FILTER FREQUENCY SELECTOR: When

setting position 1 or 4 to “ON” then position 2 or 3 up to cut-off of 30 Hz and down is for 50 Hz.

BUILT IN PROTECTION

LIMITER: During signal overload, the limiter will reduce the input audio signal enough to minimize

the amount of clipping. During normal operation, the limiter does not affect the audio signal. It will

allow brief clipping of peaks and will only activate when continuous, hard clipping occurs. When the

signal amplitude decreases enough that clipping ends, the limiter will deactivate and cease its gain

reduction. When the input signal overloads, the “CLIP LED’s” indicate a signal overload. At this

time, the “LIMITER” switch on the front panel should be in the “ON” position or the master volume

should be lowered to reduce distortion.

INPUT/OUTPUT PROTECTION: The input circuits are isolated by 10k resistors. An ultrasonic net-

work decouples RF (radio frequency) from the output and helps keep the amplifier stable with reac-

tive loads.

THERMAL PROTECTION: Variable-speed fans provides cooling airflow. During low level output

the fan runs at normal speeds. During high output and as heat raises, (exceeding 90°C), the fan will

run at high speed to aid the cooling process. The amplifier will mute until it cools down.

SHORT CIRCUIT PROTECTION: The Output Short Circuit Protection protects the output devices

from short circuits and stressful loads. During short circuit protection, the “CLIP LED” and “PRO-

TECT LED” will light simultaneously indicating amp fault. All channel output will be interrupted (i.e.

no sound output), during the “SHORT CIRCUIT PROTECTION.” SHORT CIRCUIT PROTECTION

can usually be traced back to the signal output line (i.e. Speaker Line). Check the line from the out-

put terminal to the speaker. If this line is good, check the internal speaker connections and compo-

nents. A short circuit will usually be traced to a bad cable or a bad speaker and is rarely traced to

the amplifier itself.

30 50

LOW CUT FREQUENCY

GAIN CONTROLS

The gain controls are located on the front panel and are calibrated in DB of attenuation from full

gain. It is best to adjust the amplifier so no “hissing” is heard from speakers with no music being

played.

LED INDICATORS

Each channel has 6 LEDS. 2 green LED and 2 yellow LED for level indication, 1 red LED for power

clips, 1 red LED for short / overload, and the green LED at center for power indicator.

Page 7 • American AUDIO V3000 / V2000 MK II Power Amplifier Instructions

SPECIFICATIONS

Output Power:

2 ohms, 1 khz 1% THD

4 ohms, 1khz, 1% THD

8 ohms, 1khz 1% THD

(Bridge Mode, mono)

4 ohms, 1khz, 1% THD

8 ohms, 1khz, 1% THD

Total Harmonic Distortion:

20Hz-20khz, @ rated output

power, 8 ohms

Input Sensitivity &

Impedance:

@ rated output power, 8 ohms

Dimensions & Weight:

Height:

Width:

Depth:

Weight:

Frequency Response:

+/- 1db, 1w RMS. 8 ohms

+/- 0.2 db, @ rated output, 8

ohms

Hum & Noise:

Below rated output, 8 ohms

Power Consumption:

@rated output power,8 ohms

Cooling System:

MODEL NO: V-3000

800W RMS PER CHANNEL

630W RMS PER CHANNEL

400W RMS PER CHANNEL

1500 WATTS RMS

1100 WATTS RMS

Less than 0.1%

1.0 RMS (0 dBv)

3.5” (8.8cm)

19” (48.3cm)

15.9” (40.5cm)

35 lbs. (14 kg.)

10 Hz- 40 kHz

20 Hz- 40 kHz

100 dB, unweighted

12A @ 120v AC

Dual 2 speed fans

and heatsink

Page 8 • American AUDIO V3000 / V2000 MK II Power Amplifier Instructions

American DJ® World Headquarters:

4295 Charter Street Los Angeles, CA 90058 USA

Tel: 323-582-2650 • Fax: 323-582-2610

web: www.americandj.com • e-mail: [email protected]

V-2000 MK II

540W RMS PER CHANNEL

400W RMS PER CHANNEL

250W RMS PER CHANNEL

1050 WATTS RMS

820 WATTS RMS

Less than 0.1%

1.0 RMS (0 dBv)

3.5” (8.8cm)

19” (48.3cm)

15.9” (40.5cm)

31 lbs. (14 kg.)

10 Hz- 40 kHz

20 Hz- 40 kHz

100 dB, unweighted

10A @ 120v AC

Dual 2 speed fans

and heatsink

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Amplificador de American Audio

American Audio

American Audio Power Amplifier V5000plus Manual de usuario

American Audio

American Audio V-01 Plus Series Manual de usuario

American Audio

American Audio V4002 Manual de usuario

American Audio

American Audio VLP - REV 9-10 Manual de usuario

American Audio

American Audio V4000 plus Manual de usuario

American Audio

American Audio V3001 Plus Manual de usuario

American Audio

American Audio VLP Manual de usuario

American Audio

American Audio ELX Series Manual de usuario

American Audio

American Audio VLP 2500 Manual de usuario

American Audio

American Audio Professional Power Amplifier Manual de usuario

American Audio

American Audio GX-300 Manual de usuario

American Audio

American Audio VLP1500 Manual de usuario

American Audio

American Audio VLP 2500 - REV 9-10 Manual de usuario

American Audio

American Audio Model V 5000 Manual de usuario

American Audio

American Audio Vplus Series Manual de usuario

American Audio

American Audio V1500 Manual de usuario

American Audio

American Audio ELX Series Manual de usuario

American Audio

American Audio XLT Series Manual de usuario

American Audio

American Audio VX Manual de usuario

Manuales populares de Amplificador de otras marcas

ASTRO

ASTRO HVO V40 P Manual de usuario

Marantz

Marantz SUPERSCOPE BLA-545 Instrucciones de montaje

NAD

NAD CI980 Manual de usuario

Technics

Technics SE-CH770 Manual de usuario

Harman Kardon

Harman Kardon HK6300 Manual de usuario

NAD

NAD T975 Manual de usuario

McIntosh

McIntosh MA6850 Manual de usuario

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manual de usuario

Viatron

Viatron Autrix Manual de usuario

GME

GME GA9800 Manual de usuario

Atlas

Atlas CP700 Manual de usuario

Roland

Roland KC-1000 Manual de usuario

Pyle

Pyle PFMRA350BW Manual de usuario

Advantage

Advantage S-250 Manual de usuario

IRT Electronics

IRT Electronics DVA-3007 Manual de usuario

Dimavery

Dimavery BA-100 Series Manual de usuario

Sony

Sony XM-S400D Manual de usuario

Schertler

Schertler ROY X Manual de usuario