AMC ICOM 2x20 Manual de usuario

Tabla de contenidos

Manuales populares de Amplificador de otras marcas

ASTRO

ASTRO HVO V40 P Manual de usuario

Marantz

Marantz SUPERSCOPE BLA-545 Instrucciones de montaje

NAD

NAD CI980 Manual de usuario

Technics

Technics SE-CH770 Manual de usuario

Harman Kardon

Harman Kardon HK6300 Manual de usuario

NAD

NAD T975 Manual de usuario

McIntosh

McIntosh MA6850 Manual de usuario

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manual de usuario

Viatron

Viatron Autrix Manual de usuario

GME

GME GA9800 Manual de usuario

Atlas

Atlas CP700 Manual de usuario

Roland

Roland KC-1000 Manual de usuario

Pyle

Pyle PFMRA350BW Manual de usuario

Advantage

Advantage S-250 Manual de usuario

IRT Electronics

IRT Electronics DVA-3007 Manual de usuario

Dimavery

Dimavery BA-100 Series Manual de usuario

Sony

Sony XM-S400D Manual de usuario

Schertler

Schertler ROY X Manual de usuario

Important

Do not install this equipment in a

confined space such as a book case or

similar unit.

The apparatus should not be dripped or

splashed and no objects filled with

liquids, such as vases, should not be

placed on the apparatus.

This unit should not be used near water

(e.g. near bathtub, washbowl, kitchen

sink, laundry tub, in a wet basement, or

near a swimming pool, etc.) Care should

be taken so than objects do not fall and

liquids are not spilled into enclosure

through openings.

Thank you for purchasing the iCOM 2x20 communication amplifier. This unit is designed for

powering speakers in small environments.

CONTENTS:

Before you start

System components 4

Introduction 4

Important 4

Features 4

Controls and connections

Front panel 5

Rear panel 5

Operation

Limiter 6

Installation 6

Troubleshooting 6

Specifications 7

System components

All system includes:

iCOM 2x20 1pc.

Power supply 1pc.

Instruction manual 1pc.

Introduction

Please follow the instructions in this manual to obtain the optimum results from this unit. We also

recommend that you keep this manual handy for future reference.

Important

The minimum speaker’s impedance for the stereo mode (2 channel operation) is 4Ω on each

channel.

The minimum speaker’s impedance for the bridge mode is 8Ω.

If you connect and use the unit with lower speaker’s impedance, you will damage the unit and

possibly other equipment that is connected to the device.

Do not ground the speaker output terminals!

Features

Class D high efficiency amplifier.

Stereo and bridge mode.

2MIC/Line switchable inputs: 2 unbalanced RCA and 2 balanced Phoenix.

Volume and tone controls.

Phoenix connector for output.

Built-in limiter with on /off switch.

Included 24V DC power supply.

Smart compact size for table or wall mount.

Front Panel

1. Line level RCA and Line/Mic balanced Phoenix inputs.

2. Volume control.

3. Bridge/Stereo switch. Then bridge is selected audio signal must be connected into input 2

4. Limiter on/off switch.

5. Tone control.

Rear Panel

1. Connector for power supply. DC 24V .

2. Outputs.

3. Power switch.

4. Power indicator.

Operation

Before the start, please ensure that amplifier power is off.

Connect sources such as CD player, DVD player or microphone into amplifier’s inputs.

Select bridge or stereo function by bridge/stereo switch.

Connect the outputs from the unit to your speaker. The stereo and bridge outputs are labeled

on the panel.

We recommend enabling Limiter.

Set the volumes controls into the “0” position and turn on the power.

Now you can adjust needful volume and tone levels.

Limiter

The limiter is a function that prevents very loud signals from passing through it by limiting the signal

volume temporarily to a normal level. Limiter prevents damage to the speakers or the unit itself.

The limiters primary function is to help prevent one time very loud signals such as a dropping of a

microphone or short loud parts of the music signals. Turning the limiter on may helps protect from sort

overloud, but it is not intended for total dynamics control.

Installation Troubleshooting

No power

Check power adaptor and power cable.

If power supply is good and LED of the

supply is lighting check the amplifier. If

not, please change power supply.

No sound

Check speaker’s line maybe line is

overloud and simultaneously check

maybe speakers is in short circuit.

Very high

noise

level

Check the connections of the devices,

and check signal level maybe level of the

input signal is too big. Make sure that

amplifier is not overloading.

General specifications

1. Power supply DC 24V

2. Rated power 20W each channel

3. Line inputs gain 0 dB 10kΩ

4. MIC input gain -23 dB 600Ω

5. Frequency response 50Hz – 18kHz

6. THD less 1% at 1kHz 1/3 rated power

7. S/N ratio 85dB

8. Dimensions 230x115x56

9. Weight 0,9 kg

AMC is a registered trademark of AMC Baltic www.amcpro.eu