Amazfit Bip S Manual de usuario
Amazfit Bip S User Manual
ChargingLow Battery Fully Charged
Charging Your Watch
Place the watch on the charging cradle as shown in the figure, and plug the charging
cable into a USB power adapter or USB port.
Please use a power adapter that is rated 5V and above 500mA.
1
Built-In Battery Precautions
Do not attempt to replace the device’s battery on your own orforce open the built-in
battery. Use only the ocial charging base to charge your device.
Install the Amazfit app on your phone
Search for“Amazfit”on the App Store/Google Play or
scan the QR code below to download and install the
app.
2
Connecting Your Device
Please make sure you have the Bluetooth feature activated on your phone. Then,
open the Amazfit app and follow the onscreen instructions in the app to login into an
existing account(or create a new account if needed). Once logged in, pair the device
with your phone by selecting into "Profile" > "Add device" > "Watch" > "Amazfit Bip
S". Thepairing requires the identification of the device and pressing"Pair" on the
watch.
3
Regulatory Notice
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1 . This device may not cause harmful interference, and
2 . This device must accept any interference received, including the interference that
may cause undesired operation.
FCC ID: 2AC8UA1821
Any changes or modifications that are not expressly approved by the party
responsible for the compliance may void the user’s authority to operate the
equipment.
4
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protectionagainst harmful interferences in a residential installation.
This equipment generates, uses, and may radiate radio frequency energy and,if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this product does cause harmful interference to radio
or television reception, which can be determined by turning the equipmentonand o,
the user is encouraged to try to correct the interference by oneor more of the
following measures:
5
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment andreceiver.
- Connect the equipment into an outlet on a circuit dierent from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
ThedevicehasbeenevaluatedtomeetgeneralRFexposurerequirement.Thedevice
canbeusedinportable exposureconditionwithoutrestriction.
6
This device complies with Industry Canada licence-exempt RSS standard(s). Operation
is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must acceptanyinterference, including interference that may cause
undesired operation if the device.
IC: 21806-A1821 CAN ICES-3(B)/NMB-3(B)
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radioexempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si
le brouillage est susceptible d'en compromettre le fonctionnement.
7
Under Industry Canada regulations, this radio transmitter may only operate using an
antenna of a type and the maximum(or lesser) gain approved for the transmitter by
Industry Canada. To reduce the potential of radio interference to other users, the
antenna type and it’s gain should be so chosen that the equivalent isotropically radiated
power(e.i.r.p.) is not more than that necessary for successful communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut
fonctionner avec une antenne d'un typeet d'un gain maximal (ou inférieur) approuvé
pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son
gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas
l'intensité nécessaire à l'établissement d'une communication satisfaisante.
8
Disposal and Recycling Information
The following symbol signifies that this product has to be disposed
separately from ordinary household wastes at its end of life. Please kindly be
aware that this is your responsibility to dispose the electronic equipment at
recycling centers so as to help conserve the natural resources.
9
Otros manuales para Bip S
1
Tabla de contenidos
Otros manuales de Mirar de Amazfit
Amazfit
Amazfit GTS 4 Manual de usuario
Amazfit
Amazfit GTS 3e Manual de usuario
Amazfit
Amazfit T-Rex 2 Manual de usuario
Amazfit
Amazfit JHS20W2 Manual de usuario
Amazfit
Amazfit GTS 2 mini Manual de usuario
Amazfit
Amazfit Band 7 Manual de usuario
Amazfit
Amazfit GTS 3 Manual de usuario
Amazfit
Amazfit GTS 2e Manual de usuario
Amazfit
Amazfit Verge Lite Manual de usuario
Amazfit
Amazfit T-Rex Manual de usuario
Amazfit
Amazfit GTR3 pro Manual de usuario
Amazfit
Amazfit Bip Pro 3 Manual de usuario
Amazfit
Amazfit GTS 4 mini Manual de usuario
Amazfit
Amazfit BALANCE Manual de usuario
Amazfit
Amazfit GTS 2 Manual de usuario
Amazfit
Amazfit X Manual de usuario
Amazfit
Amazfit T-Rex Ultra Manual de usuario
Amazfit
Amazfit GTR Manual de usuario
Amazfit
Amazfit Neo Manual de usuario
Amazfit
Amazfit Verge Manual de usuario
