Altronix Trove T1RSH3F8 Manual de usuario
T1RSH3F8
Fully assembled kit includes:
- Trove1R rack enclosure with
Altronix/Software House backplane (TSH1R)
- (1) eFlow6NB - Power Supply/Charger
- (1) VR6 - Voltage Regulator
- (1) ACMS8 - Fused Dual Output Access Power Controller
Access & Power Integration
Rev. T1RSH3F8112618 More than just power.TM
Installing Company: _______________ Service Rep. Name: __________________________________
Address: _____________________________________________ Phone #: __________________
Installation Guide
All registered trademarks are property of their respective owners.
All components of this Trove kit are UL Listed sub-assemblies.
Please refer to the included corresponding
Sub-Assembly Installation Guides for further information.
- 2 - T1RSH3F8 Installation Guide
Overview:
Altronix T1RSH3F8 rack kit is pre-assembled and consist of Trove1SH1R enclosure/backplane with factory
installed Altronix power supply/charger and sub-assemblies. This kit also accommodates various combinations of
Software House boards for up to eight (8) doors in a single enclosure.
Configuration Chart:
Altronix
Model
Number
120VAC
60Hz
Input
Current
Power
Supply
Board
Input
Fuse
Rating
Power
Supply
Board
Battery
Fuse
Rating
Nominal DC
Output Voltage Maximum Supply
Current for Main
and Aux. Outputs on
Power Supply board
and ACMS8 Access
Power Controller’s
outputs
Fail-Safe/
Fail-Secure or
Dry Form “C”
Outputs
ACMS8
Board
Input
Fuse
Rating
ACMS8
Board
Output
Fuse
Rating
[DC] [Aux]
Output
Range
(VDC)
Output
Range
(VDC)
T1RSH3F8 3.5A 5A/
250V
15A/
32V
20.17-
26.4
20.28-
26.4 24VDC @ 5.4A 815A/
32V
3A/
32V
Hardware and Accessories:
Specifications:
Spacer | 5/16” Pan Head Screw | Lock Nut
Agency Listings:
• CE European Conformity.
Mechanical:
• Black enclosure with ample knockouts for
convenient access.
• Includes: tamper switch, cam lock and
mounting hardware.
• Modular 2U standard EIA 19” drawer with
extendable slides up to 48”.
• Dimensions (H x W x D): 3.375” x 19.0” x 26.5”
(85.8mm x 482.6mm x 673.1mm)
Included Accessories:
• One (1) tamper switch
(Altronix Model TS112 or equivalent).
• Cam lock.
Available Accessories (not included):
• RE2: Rack Mount Battery Enclosure
accommodates up to four (4) 12VDC/7AH batteries.
• WM5, WM25, WM100: Magnetic Cable Tie Mounts
(5, 25, 100 counts).
T1RSH3F8 Installation Guide - 3 -
Installation Instructions for T1RSH3F8:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local
codes and authorities having jurisdiction. These products are for indoor use only and must be installed within
the protected premises.
Note: First assemble and Install Z Bracket Wire Management Accesory
(refer to Z Bracket Installation pg. 4)
1. Remove backplane from enclosure prior to installing into rack cabinet
(do not discard hardware).
2. In order to mount included UL Listed tamper switch (Altronix Model TS112 or
equivalent) turn the enclosure upside down. Punch out the knockout in
designated location, on the back of the unit, from outside of the drawer
(Fig. 1, pg. 3). Insert the tamper switch into the knockout from outside of the
drawer with the button facing outwards and spaded connectors inside the drawer.
Connect tamper switch wiring to the Access Control Panel input or the
appropriate UL Listed reporting device.
To activate alarm signal open the rack drawer.
3. Slide the rack enclosure into an open 2U location in the four post rack cabinet.
4. Utilizing proper fasteners attach front ears to the rack rails.
5. Attach the rear of the adjustable slides to the rear rails of the rack cabinet with the proper fasteners.
6. Secure the rack cover (Fig. 2a, pg. 3) and rack drawer to earth ground (Fig. 2b, pg. 3).
7. Ensure that all internal cofigurations (voltage selection, switch settings, etc.) are completed before
mounting backplane back into Trove rack enclosure.
8. After all components are mounted on the backplane, attach it to the enclosure using included hardware.
9. Mount Software House modules to TSH1R backplane, refer to page 5.
10. Refer to the eFlow Power Supply/Charger Installation Guide for eFlow6NB and corresponding sub-assembly
Installation Guides for the following models: ACMS8(CB), VR6 for further instructions.
Fig. 1
Back of the drawer,
viewed from outside.
Tamper Switch
mounting location
Fig. 2
Fig. 2a
Fig. 2b
- 4 - T1RSH3F8 Installation Guide
Assembling and Attaching
Z Bracket Wire Management Accessory (included):
Altronix Trove Rack enclosures include Z Bracket, a convenient and reliable wire management accessory.
Hardware (included):
Ten (10) bolts and eight (8) lock nuts.
1. Carefully unpack Z Bracket. Do not discard hardware
(included) (Fig. 3, pg. 4).
2. Attach arms to each other using bolts and
lock nuts (Fig. 3a, pg. 4).
3. Attach the hinge brackets to the ends of
arms using bolts and nuts positioning
them as shown on (Fig. 3b, pg. 4).
4. Make sure that all nuts are tightened.
5. Attach the hinge bracket on the longer side of Z Bracket to the adjustable slide using bolts and lock nuts
(included) (Fig. 4, 4a, pg. 4).
6. Attach the hinge bracket on the shorter side of Z Bracket to the rear of the rack enclosure using bolts
(included).
Fig. 4
Fig. 4a
Fig. 3b
Two (2)
Fig. 3
Fig. 3a
T1RSH3F8 Installation Guide - 5 -
T1RSH3F8:
Configuration of Software House Modules
1. Fasten spacers onto metal pems configuration (A), (B), or (C) of backplane depending on the access controller
(Fig. 5, pg. 5).
2. Position access controller module over corresponding spacers and fasten screws into spacers (Fig. 5a, pg. 5).
Note: Software House iSTAR Ultra ACM and iSTAR ACM SE/ACM PRO boards have one (1) USB port each.
Please orient boards in the appropriate position according to the Fig. 5 below.
3. Mount backplane to enclosure with hardware.
Access Controller Position Chart for the Following Models:
Software House Access Controller Pem Mounting
iSTAR Ultra ACM A
iSTAR ACM SE/ACM PRO B
I8, R8 or I8-CSI Module C
Fig. 5
Altronix
eFlow6NB
AC
L G N
DCAC1 1min
enable
2hr.
disable
OFF - 24V
ON - 12V
ON
TRIGGER EOL
SUPERVISED
--- BAT+ --- DC +
NC C NO
AC FAIL
NC C NO
BATFA IL
+AUX ---
NO GND
RESET
Altronix ACMS8
PWR1 +
PWR2 +
COM -
COM -
PWR2 +
PWR1 +
+ PWR2 --
+ PWR1 --
VR6 is
mounted
under
ACMS8
USB PORT
A
C
C
C
USB PORT
B
To IEC connector
To LED
lense
Pem
Spacer
Backplane
Pan Head Screw
Software House
Board
Fig. 5a
- 6 - T1RSH3F8 Installation Guide
Notes:
T1RSH3F8 Installation Guide - 7 -
Notes:
- 8 - T1RSH3F8 Installation Guide
Trove1R Enclosure Dimensions:
3.375” x 19.0” x 26.5” (85.8mm x 482.6mm x 673.1mm). Shown with Z Bracket attached.
0.1”
2.5mm
1.5”
38.1mm
11.175” (283.8mm)
2.4”
61mm
4.57”
116.1mm
3.375”
85.8mm
26.5”
673.1mm
19” (482.6mm)
R 1.27” (32.3mm)
1” (25.4mm)
0.55” (14mm)
3.62”
92mm
Altronix is not responsible for any typographical errors.
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056
IIT1RSH3F8 I02U MEMBER
Tabla de contenidos
Otros manuales de Recinto de Altronix
Altronix
Altronix Trove1V1R Manual de usuario
Altronix
Altronix Trove T1MK1F4V Manual de usuario
Altronix
Altronix Trove1V1R Manual de usuario
Altronix
Altronix Trove1M1R Manual de usuario
Altronix
Altronix Trove T1SAK34 Manual de usuario
Altronix
Altronix TROVE T2MK34D Manual de usuario
Altronix
Altronix Trove2BL2 Manual de usuario
Altronix
Altronix TROVE TDMD2 Manual de usuario
Altronix
Altronix Trove2AG2 Manual de usuario
Altronix
Altronix TROVE Trove1AG1R Manual de usuario
Altronix
Altronix Trove T2KSK3F8 Manual de usuario
Altronix
Altronix TROVE Trove3WC Series Manual de usuario
Altronix
Altronix TROVE Trove2HW2 Manual de usuario
Altronix
Altronix Trove2 Manual de usuario
Altronix
Altronix TROVE T1DMK3F4 Manual de usuario
Altronix
Altronix Trove 1AL1R Manual de usuario
Altronix
Altronix RE2 Manual de usuario
Altronix
Altronix TROVE T1MK1F4 Manual de usuario
Altronix
Altronix TROVE T2MK3F4D Manual de usuario
Altronix
Altronix Trove1BL1R Manual de usuario
