ALTAI IX500 Manual de usuario
1
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
ALTAI IX500 Indoor 2x2
802.11 ac W av e 2 AP
_________________________________________________
Quick Setup Guide
Version 1.0
2
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
Introduction
Thank you for purchasing the ALTAI IX500 product. This guide provides
instructions to install the product and set it up as AP with minimal effort.
Package Contents
Ceiling Mount Base
(15/16” T-Rail)
Ceiling Mount Base
(9/16” T-Rail)
IX500 Main Unit
Quick Setup Guide
Back Cover
(For Indoor Installation)
Dry Wall Mount Kit
-Anchors x 2
-Screws x 2
Back Cover
(For Outdoor Installation)
Optional Items
Wall/Pole Mount Kit
-Mount Base x 1
-Anchors (For Concrete Wall) x 2
-Screws (For Concrete Wall) x 2
-Cable Tie (For Pole) x 2
3
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
Hardware Overview
LED Indicator
Power/Booting
Status
Off
AP Powered Off
Flashing Red
AP Booting Up
Solid Red
AP Boot Up Finished and Ready for Service
2.4G Radio
Enabled Only
(AP/Station/
Repeater)
Solid Purple
1. AP Mode on but with no Client Association; OR
2. Station Mode on but not connected to Remote AP; OR
3. Repeater Mode on but not connected to Remote AP
Alternate Flashing
Purple & Red
Data Transmitting/Receiving
5G Radio
Enabled Only
(AP/Station/
Repeater/Bridge)
Solid Yellow
1. AP Mode on but with no Client Association; OR
2. Station Mode on but not connected to Remote AP; OR
3. Repeater Mode on but not connected to Remote AP; OR
4. Bridge Mode on but not connected to Remote Peer
Alternate Flashing
Yellow & Red
Data Transmitting/Receiving
2.4G and 5G
Radios Enabled
(AP/Station/
Repeater/Bridge)
Solid White
AP/Station/Repeater/Bridge Mode on but with no
connection with Client/Remote AP/Remote Peer
Alternate Flashing
Purple, Yellow & Red
Data Transmitting/Receiving
LED Indicator
4
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
Ethernet Port, DC Power Jack and Reset Button
Ethernet Port:
It is used to connect to power source (see the Power Options in the later
section) and provides 10/100/1000 Mbps network interface for LAN
connection.
DC Power Jack:
It is used to connect to DC power source of 12VDC/1A as another power
option.
Reset Button:
Ethernet Port
Reset Button
DC Power
Jack
Mount
Base Slot
Red LED Indicator
0s
1-2s
5-8s
Factory Reset
Reboot
It serves two functions:
Reboot: Press and hold the
Reset Button for 2-3 seconds
until the red LED blinks once.
Factory Reset: Press and hold
the Reset Button for 5-8
seconds until the red LED
blinks twice consecutively.
5
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
Mounting Options
Option 1: T-Rail Ceiling Mount (9/16” T-Rail OR 15/16” T-Rail)
2
Insert an appropriately sized ceiling rail
into one of the mount base slots first. Then
turn the AP slightly so that the rail slips into
another slot to lock the AP into place.
1
Select an appropriate ceiling
mount base (9/16” or 15/16”)
and slide the base into the
slot of the AP.
6
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
Option 2: Wall Mount (Concrete Wall)
1
Determine where the AP is to be placed and mark location on the
wall surface for the two mounting holes of the mount base. Use an
appropriate drill bit to drill holes of 1/3”(8.1mm) diameter and 1”
(26mm) deep. Screw the anchors into the holes and then insert the
screws through the mount base to the anchors to attach the base to
the wall.
2
Slide the base into the
slot of the AP.
7
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
Option 3: Pole Mount (For 1 inch to 3 inches of pole diameter)
1
Thread the open end of the
cable tie through the two
slots of the mount base.
2
Slide the base into
the slot of the AP.
3
Determine where the AP is to be placed. Tighten
the cable tie to secure the base to the pole.
8
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
Setup Requirements and Preparation
A computer with Web Browser: Google Chrome, Mozilla Firefox, or
Microsoft Internet Explorer 8 (or above)
Two Cat 5e/6 Ethernet cables
802af/at-compliant PoE switch (54Vdc/0.6A)
AltaiCare account (Optional) for cloud AP management and user service
Power Options and Cable Connection Instructions
1. Connect the IX500 Ethernet port to an 802.3af/802.at-compliant PoE switch
with an Ethernet Cable.
2. Connect a computer to the switch.
3. Make sure the LED indicator turns into a solid light for AP configuration.
802.3af/802.at –Compliant
PoE Switch
IX500 AP
Ethernet Cable
(PoE + Data)
Ethernet Cable
(Data)
9
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
1. Change TCP/IP Setting on Your Computer
For Windows 7 users,
1. Go to Control Panel, click Network and Sharing Center and then choose
the adapter that you want to connect to IX500 unit. In this example,
adapter “Local Area Connection” is in connection with IX500-S. Click it
and then click Properties.
2. Under the Networking tab, click Internet Protocol Version 4 (TCP/IPv4) in
the list box “This connection uses the following items”, and then click
Properties.
3. Type in the following IP address and Subnet mask:
IP address: 192.168.1.2
Subnet mask: 255.255.255.0
4. Click OK to close the Internet Protocol Version 4 (TCP/IP) Properties dialog
box and click OK again to close the Local Area Connection Properties
dialog box.
10
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
2. Access to Web Interface
1. Open a web browser. Type 192.168.1.222 in the address bar and then hit
Enter.
2. Login page will come up and you are required to enter username and
password. By default, the credentials are:
Username: admin
Password: admin
3. Click Login.
Tabla de contenidos
Otros manuales de Punto de acceso inalámbrico de ALTAI
ALTAI
ALTAI A2 Manual de usuario
ALTAI
ALTAI C260 Manual de usuario
ALTAI
ALTAI A175FD Manual de usuario
ALTAI
ALTAI A3-Ei Manual de usuario
ALTAI
ALTAI CX200 Manual de usuario
ALTAI
ALTAI A2N Hoja de instrucciones
ALTAI
ALTAI A2 Hoja de instrucciones
ALTAI
ALTAI A3 Series Manual de usuario
ALTAI
ALTAI C2s Manual de usuario
ALTAI
ALTAI A2C Manual de usuario
