Alpha AWS-125 Manual de usuario
Part No: AWS-125 / AWS-225
103 Bauer Drive, Oakland, NJ 07436 • 800-648-7229 • Fax: 800-286-0114
www.alpha-tools.com
Alpha®Wet Stone Cutter
Instruction Manual
MANUAL
2
TABLE OF CONTENTS
Introduction................................................................................................................ 3
About Symbols................................................................................................... 3
Electrical Symbols ............................................................................................. 3
Safety instructions .................................................................................................... 4
For Safe Operation............................................................................................. 4
AWS-125 Overview .................................................................................................... 6
Accessories ............................................................................................................... 7
Additional Precautions for Using the Wet Stone Cutter........................................ 8
AWS-125 Wet Stone Cutter Operation ..................................................................... 9
Main Connection ................................................................................................ 9
Switching ON and OFF ...................................................................................... 9
Ground Fault Circuit Interrupter..................................................................... 10
Before Use.................................................................................................................11
About Double Installation................................................................................ 12
Laws and Regulations of Noise Levels.......................................................... 12
Instructions for Installing the Felt Strips....................................................... 12
Installation of Water Attachment .................................................................... 13
Water Flow........................................................................................................ 14
Adjusting Cutting Depth ......................................................................................... 14
Assembling and Disassembling ............................................................................ 14
Straight Blade Installation ...................................................................................... 15
Curve Blade Installation.......................................................................................... 15
Free-Hand Cutting ................................................................................................... 16
Cutting Using Ruler Guide...................................................................................... 16
Cutting Using the Carriage Assembly and Guide Rail......................................... 17
Curve Cutting Application ...................................................................................... 18
Blade Inspection, Installation and Removal ......................................................... 19
AWS-125 Maintenance ............................................................................................ 20
Replacing and Checking the Carbon Brushes ..................................................... 21
Recommended Accessories................................................................................... 24
Service and Warranty Information ......................................................................... 26
Loaner Program ............................................................................................... 26
AWS-125 Wet Stone Cutter Schematic .................................................................. 27
AWS-125 Wet Stone Cutter Parts List.................................................................... 28
EC Declaration of Conformity ................................................................................ 30
Warranty ................................................................................................................... 30
Product Registration Card...................................................................................... 31
3
INTRODUCTION
Thank you for purchasing theAlpha®AWS-125 Wet Stone Cutter. Please read this instruc-
tion manual thoroughly to ensure safe and correct use of the wet stone cutter. Keep this
manual in a place where operators can access it easily whenever necessary.
ABOUT THE SYMBOLS
According to the hazard level, all safety notes in this manual are classied into “DANGER”,
“WARNING”, and “CAUTION”.
DANGER! Deathorseriouspersonalinjuryisimminentwhenhandlingthistool
incorrectly.
WARNING! There is a possibility of death or serious personal injury when
handling this tool incorrectly.
CAUTION! Thereisapossibilityofpersonalinjuryorpropertydamagewhen
handling this tool incorrectly.
NOTE: In some situations, failing to observe WARNING notes could result in death or seri-
ous personal injury. Be sure to read and observe the safety notes to ensure safety
and correct use of the wet stone cutter.
ELECTRICAL SYMBOLS
The following show the symbols used for tool.
V Volts
A Amperes
Hz Hertz
~ or a.c. Alternating Current
n0 No load speed
…/min Revolution or reciprocation per minute
kg Kilograms
Protective Earth
4
Note: In some situations, failing to observe WARNING notes could result in deathor
serious personal injury. Be sure to read and observe the safety notes to ensure
safe and correct use of the wet stone cutter.
CAUTION!
The following are important notes for products, operation, and maintenance applicable to
this stone cutter.
SAFETY INSTRUCTIONS
Read all these instructions before attempting to operate this product.
WARNING!
When using electric tools, basic safety precautions should always be followed to reduce the
risk of re, electric shock, and personal injury, including the following.
For Safe Operation
1. Keep work area clean
Cluttered areas and benches invite injuries.
2. Consider work area environment
Do not expose power tools to rain. Do not use power tools in damp or wet locations
without GFCI protection. Keep work areas well lit. Do not use the tool in presence of
ammable liquids or gases.
3. Guard against electric shock
Prevent bodycontact withgrounded surfaces.For example:pipes, radiators,ranges,
and refrigerator enclosures; use grounded outlets.
4. Keep children and visitors away
Donotlet visitorscontact toolor extensioncord. Allvisitorsshould bekept awayfrom
work area. Keep out of reach of children.
5. Tool Storage
Whennotinuse,toolsshouldbe storedinasecuredry location.Alockedstoragearea
or high shelf out of children’s reach is ideal.
6. Do not force the tool
It will do the job better and be safer at the rate for which it was intended.
7. Use the right tool
Do not force a small tool or attachment to do the job of a heavy-duty tool. Do not use
the tool for purposes it is not designed for – (for example – do not use stone cutter for
cutting tree limbs or logs.)
8. Dress properly
Do not wear loose clothing or jewelry. Items such as these can be caught in moving
parts. Rubberglovesandnon-skidfootweararerecommendedwhenworkingoutdoors.
Wear protective hair covering to contain long hair.
9. Use safety equipment
Always wear safety glasses and if necessary, a face shield, dust mask and hearing
protection.
5
10. Do not abuse the electrical cord
Nevercarrythe toolby theelectrical cordor pullitto disconnectfrom receptacle. Keep
the electrical cord away from heat, oil and sharp edges.
11. Secure workpiece
Use clamps or a vise to hold workpiece rather than using your hands.
12. Do not overreach
Keep proper footing and balance at all times.
13. Maintain tools with care
Keep tools sharp and clean for better and safer performance. Follow instructions for
lubricating and changing accessories. Inspect the electrical cord periodically and
if damaged, have it repaired by authorized service facility. Inspect extension cords
periodically and replace if damaged. Keep handles dry, clean and free from oil and
grease.
14. Disconnect tools
Disconnectthetoolfromthepowersupplywhennotinuse,beforeservicing,andwhen
changing accessories, such as blades, bits, cutters.
15. Remove adjusting keys and wrenches
Check to see that keys and adjusting wrenches are removed from the tool before
turning it on.
16. Avoid unintentional starting
Do not carry a plugged-in tool with nger on switch. Be sure the switch is off when
plugging in.
17. Outdoor use extension cords
When tool is used outdoors, use only extension cords intended for use outdoors and
so marked.
18. Stay alert
Use caution and do not operate tool when you are tired or on medication.
19. Check for damaged parts
Beforeusingthetooleachday,aguardorotherpartthatisdamagedshouldbecarefully
checked to determine that it will operate properly and perform its intended function.
Check for alignment of moving parts, breakage of parts, mounting, and any other
conditions that may affect its operation.A guard or other part that is damaged should
be properly repaired or replaced by an authorized service center unless otherwise
indicated elsewhere in this instruction manual. Have defective switches replaced by
authorized service center. Do not use the tool if it cannot be turned on and off by the
switch.
20. Warning
The use of any other accessory or attachment other than recommended in this
instruction manualor thecatalog maypresentariskof personalinjuryandcouldvoid
the warranty.
21. Only qualied technicians should repair this tool
This electric tool is manufactured in accordance with the standard safety rules. Only
expertsmaycarry outthe repairofelectric tools;otherwise, itmay causeconsiderable
danger for the operator.
6
AWS-125 OVERVIEW
SPECIFICATIONS
Rating ................................................................................................110/220 Volts
Amperage................................................................................................... 11.2/5.5
Power........................................................................................................... 1200W
No-load Speed ....................................................................................12,000 RPM
Weight ............................................................................................... 7.2 lbs/3.3kg
Arbor..................................................................................................7/8” / 22.23m
Cutting Disc Diameter........................................................................5” / 125mm,
Maximum Cutting Depth................................................................ 1-5/8” / 41mm
Power Switch
Power Switch
Lock
Side Handle
Water Valve
Flange I and
Flange II
Height Adjustment
Wing Screw
TT Ruler Guide
Water Nozzle
Figure-1
7
ACCESSORIES
COMPONENTS:
1. Ground Fault Circuit Interrupter (Part No. 133289/133292)
2. Water Valve (Part No. 133362)
3. Water Attachment Assembly (Part No. 133287)
4. Spanner Wrench M 22 (Part No. 133097)
5. TT Ruler Guide (reversible) (Part No. 133266)
6. T-Handle Wrench (Part No. 133098)
7. Extra Carbon Brush (2 pc set) (Part No. 133033)
8. Self-stick Felt Strip Set (Part No. 133369)
9. Side Handle (Part No. 801086)
Figure-2
8
ADDITIONAL PRECAUTIONS FOR USING
THE WET STONE CUTTER
In addition to the general safety notes described on the preceding pages, please read
and observe the following precautionary notes before using the wet stone cutter.
DANGER!
INSTRUCTIONS
AlphaProfessionalTools® provides the highest quality parts and manufacturing techniques
in the manufacture of this tool. In order to obtain the maximum effectiveness and provide
thehighestdegree ofsafety, itis necessaryto reviewand followthese instructionscarefully
before using the tool.
SAFETY ADVICE
• Please note safety instructions on Page 3-5.
• Do not pierce the motor housing as this could damage the double insulation.
• Always remove plug from the outlet before making any changes to the settings or
carrying out maintenance.
• Only plug-in when machine is switched off.
• Keep power cable clear from working range of the machine. The power cable should
always lead away from you and behind the operating area.
• Before use, check the machine, cable and plug for any damages or material fatigue,
only authorized service agents should carry out repairs.
• After switching off, the machine will not idle down immediately. Allow the machine to
come to a complete stop before putting it down.
• Always wear safety glasses and ear protection when working with this machine. It
is further recommended to wear safety gloves, apron, as well as sturdy non-slipping
shoes.
• Only use saw blades whose permitted speed is at least as high as the highest no-load
speed of the machine.
• Be sure saw blade ts tool properly and securely. Do not modify the tool to force t the
blade. For example do not remove blade guard.
• Check cutting tools before use. The saw blade must be properly mounted and turn
freely. Performatestrunforatleast30secondswithoutanyload. Donotusedamaged,
out of round or vibrating cutting tools.
• Immediately switch off the machine in case of considerable vibrations or if other
malfunctions occur. Check the machine in order to nd out the cause.
9
• Always use and store the saw blades according to the manufacturer’s instructions.
The ange bolt must be tightened before starting to work with the machine.
• The work piece must be secured if it is not heavy enough to prevent movement.
• Do not use emery wheel.
• The tool is designed for cutting on horizontal surfaces.
USAGE
This wet stone cutter can be used for cutting many different materials, e.g. tile, concrete,
stone orglass. Incase ofdoubtpleasereadthe manufacturer’sinstruction.Donotuse this
product in any other way as stated for normal use.
AWS-125 WET STONE CUTTER OPERATION
MAIN CONNECTION
Connect only to single-phase AC current supply and only to the main voltage specied on
theratingplate.Connectiontosocketswithoutgroundprotectionispossibleastheappliance
features protective insulation to DIN 57/740/ VDE 0740 and CEE 20. Radio suppression
complies with the European standard EN 55014.
SWITCHING ON AND OFF
Intermittent use
Switching on: Press switch trigger
Switching off: Release switch trigger
Continuous use:
Switching on: Press the on/off switch and then the locking button; release on-off switch.
Switching off: Press the on/off switch and then release.
Locking Button
Switch Trigger Figure-3
10
GROUND FAULT CIRCUIT INTERRUPTER:
DANGER!
Do not bypass the GFCI if this condition occurs, a real shock hazard may exist.
WARNING!
If the GFCI fails to trip when the test button is pressed, or fails to reset, the device is
defective and should be replaced.
If the GFCI tests properly without a load applied, but trips each time a load is connected,
then the load (tool) has a ground fault condition and needs to be repaired or replaced.
Do not bypass the GFCI if this condition occurs, a real shock hazard may exist.
CAUTION!
1. The GFCI is a safety device, do not use as an off/on switch.
2. The GFCI on the tool will not protect you if you cut into another current carrying
conductor.
3. Do not use where water may enter GFCI case.
4. Do not modify or allow GFCI to be immersed in water.
AGround Fault Circuit Interrupter (GFCI) is mounted at the end of power supply cord.
The GFCI goes OFF when water enters inside the tool’s housing preventing the operator
from receiving electric shocks.
When the GFCI goes OFF, the Reset button pops up.
This is the result of water entering the stone cutter
housing.
Turn OFF the power switch and blow dry air inside the
motor cover through the air vents.
Press the GFCI Reset button. The stone cutter is
ready to start working after the reset button is pressed
down.
1. Do not remove the GFCI.
Reset
Test
Figure-4
Red Run
Light
Otros manuales para AWS-125
2
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Cortador de Alpha
Manuales populares de Cortador de otras marcas
Milwaukee
Milwaukee HEAVY DUTY M12 FCOT Manual de usuario
Makita
Makita DCS552 Manual de usuario
SignWarehouse.com
SignWarehouse.com Bobcat BA-60 Manual de usuario
Makita
Makita 4112HS Manual de usuario
GEISMAR STUMEC
GEISMAR STUMEC MTZ 350S Manual de usuario
Hitachi
Hitachi CM 4SB2 Guía de solución de problemas
