Alpha Professional Tools COTE-04 Manual de usuario
103 Bauer Drive, Oakland, NJ 07436 • 800-648-7229 • Fax: 800-286-0114
www.alpha-tools.com
Alpha®Pneumatic
4” Extended
Cut-Off Tool
MANUAL
Part No: COTE-04
Version 2
Safety Warning: Always wear eye and respiratory protection as
well as proper personal safety equipment when using this product.
Comply with ANSI B7.1 and OSHA requirements.
2
i
TABLE OF CONTENTS
Introduction.......................................................................................... 2
About the Symbols .............................................................................. 2
Safety Instructions for Pneumatic Tools .............................................. 2
COTE-04 Features .............................................................................. 4
COTE-04 Overview ............................................................................. 5
Removal/Installation of the Blade........................................................ 6
COTE-04 Schematic............................................................................ 8
COTE-04 Parts List ............................................................................. 9
Accessories and Factory Service ...................................................... 11
Product Registration.......................................................................... 12
For repair information call:
Headquarters, Oakland, NJ — (800) 648-7229 ext.505
Due to specially designed components this machine must be serviced only
with genuine ALPHA®parts.
2
INTRODUCTION
Thank you for purchasing an Alpha®Pneumatic Extended Cut-Off Tool. A wide range
of accessories help you perform many different tasks. For your safety, please read
this manual thoroughly before you start operating this polisher.
ABOUT THE SYMBOLS
According to the hazard level, all safety notes in this manual are
classied into “DANGER”, “WARNING”, and “CAUTION”.
DANGER! Death or serious personal injury is imminent when
handling this tool incorrectly.
WARNING! There is a possibility of death or serious personal
injury when handling this tool incorrectly.
CAUTION! There is a possibility of personal injury or property
damage when handling this tool incorrectly.
Note: In some situations, failing to observe WARNING notes could result in death
or serious personal injury. Be sure to read and observe the safety notes
to ensure safety and correct use of the tool.
SAFETY INSTRUCTIONS FOR POWER TOOLS
1. KNOW YOUR POWER TOOL. Read owner’s manual carefully.
Learn its applications and limitations as well as specic potential
hazards particular to this tool.
2. KEEP WORK AREA CLEAN. Cluttered areas and benches invite
accidents.
3. AVOID DANGEROUS ENVIRONMENTS. Keep work areas as dry
as possible. Do not use tool in presence of ammable liquids or
gases. Keep the area well lit.
4. KEEP CHILDREN AND VISITORS AWAY. All visitors should be kept
a safe distance from the work area. Keep out of reach of children.
3
5. DON’T FORCE TOOL. It will do the job better and safer at the rate
for which it was designed.
6. WEAR PROPER APPAREL. Do not wear loose clothing or jewelry
as it can get caught in moving parts. Rubber gloves and insulated
non-skid footwear are recommended. Wear protective covering to
contain long hair.
7. WEAR PROPER EYE PROTECTION. All users and bystanders
must always wear proper personal eye protection which conform with
ANSI/ISEA Z87.1 (CAN/CSA Z94.3). Also use a face or dust mask if
operation is dusty. Always wear certied safety equipment.
8. WEAR PROPER EAR PROTECTION. All users and bystanders
must wear proper personal ear protection which conforms with ANSI
S12.6 (S3.19) hearing protection.
9. WEAR PROPER RESPIRATORY PROTECTION. All users and
bystanders must wear proper personal respiratory protection. Always
use NIOSH/OSHA approved respiratory protection appropriate for the
dust exposure.
Warning: Some dust created by power sanding, sawing, grinding, drilling,
polishing and other construction activities contains chemicals known to the
State of California to cause cancer, birth defects, or other reproductive harm.
Some examples of these chemicals are:
- Lead from lead-based paints
- Crystalline silica from bricks, cement and other masonry products, and
- Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this
type of work. To reduce your exposure, work in a well ventilated area, and
work with approved safety equipment, such as dust masks that are specially
designed to lter out microscopic particles.
To familiarize with the risks associated with a material, consult with your
employer, manufacturer/supplier and government agencies regarding the
hazards of the materials and their recommendations to protect yourself.
10. ALWAYS SECURE WORK PIECE. Use clamps or a vise to hold work.
It’s safer than using your hand and it frees both hands to operate tool.
11. DON’T OVERREACH. Keep proper footing and balance at all times.
12. DISCONNECT TOOLS WHEN NOT IN USE. Always disconnect tool
before servicing; when changing accessories.
13. REMOVE ADJUSTING KEYS AND WRENCHES. Form a habit of
checking to see that keys and adjusting wrenches are removed from
tool before turning it on.
4
14. MAINTAIN TOOLS WITH CARE. Keep tools clean at all times for
best and safest performance.
15. AVOID ACCIDENTAL STARTING. Do not carry a “connected” tool,
or make adjustments, or change blades without making sure the tool
is disconnected from the air supply.
16. USE ONLY RECOMMENDED ACCESSORIES. The use of any
accessories other than what is listed or recommended for this
particular tool may be hazardous.
17. KEEP HANDS AWAY FROM ALL MOVING PARTS.
18. USE SIDE HANDLES. Supplied with tool for control and safety.
19. STAY ALERT. Watch what you are doing and use common sense.
Do not operate tool when you are tired, or under the inuence of
medication or alcohol.
FEATURES
Built-In Spindle Lock
Rear Exhaust
Built-In Cushion Grip
Push to Adjust Safety Guard
11 Position Adjustable Swivel Guard
(126° Adjustable Range)
Powerful Motor (1.0 HP/0.7KW)
5
COTE-04 OVERVIEW
SPECIFICATIONS:
Free Speed .....................................................................14,000 RPM
Cutting Disc Dimensions...........................4” (100mm) x 3/8” (10mm)
Air Inlet................................................................................. 1/4” NPT
Hose Size ID.................................................................. 3/8” (10mm)
Air Consumption ...................................................4 CFM (113 L/min)
Length..................................................................... 14-3/4” (377mm)
Weight..........................................................................3.7 lbs (1.7kg)
Noise Level .......................................................................... 85 dB(A)
Recommended Air Pressure.....................................90 PSI (6.2 Bar)
Figure-1
6
REMOVAL/INSTALLATION OF THE BLADE
CAUTION!
1. Press and hold the spindle lock. (See Fig. 2)
2. Insert the Hex Key Wrench inside the screw. (See Fig. 3)
Figure-2
Figure-3
7
REMOVAL/INSTALLATION OF THE BLADE
CAUTION!
3. While continuing to hold the spindle lock button, turn the Hex Key
Wrench in a counter clockwise rotation to loosen and remove the
screw and ange from the spindle. (See Fig. 4)
Figure-4
Reverse To Install New Blade
8
ALPHA®COTE-04 SCHEMATIC
Tabla de contenidos
Otros manuales de Cortador de Alpha Professional Tools
Alpha Professional Tools
Alpha Professional Tools PSC-600 Manual de usuario
Alpha Professional Tools
Alpha Professional Tools Ecocutter ECC-125 Hoja de especificaciones
Alpha Professional Tools
Alpha Professional Tools ESC-125 Manual de usuario
Alpha Professional Tools
Alpha Professional Tools PSC-150 Manual de usuario
Alpha Professional Tools
Alpha Professional Tools WBCKIT Manual de usuario
Alpha Professional Tools
Alpha Professional Tools WBC5KIT Manual de usuario
Alpha Professional Tools
Alpha Professional Tools AWS-110 Manual de usuario
Alpha Professional Tools
Alpha Professional Tools ESC-125 Manual de usuario
Alpha Professional Tools
Alpha Professional Tools ESC-150 Manual de usuario
Alpha Professional Tools
Alpha Professional Tools Ecocutter ECC-125 Manual de usuario
Manuales populares de Cortador de otras marcas
Milwaukee
Milwaukee HEAVY DUTY M12 FCOT Manual de usuario
Makita
Makita DCS552 Manual de usuario
SignWarehouse.com
SignWarehouse.com Bobcat BA-60 Manual de usuario
Makita
Makita 4112HS Manual de usuario
GEISMAR STUMEC
GEISMAR STUMEC MTZ 350S Manual de usuario
Hitachi
Hitachi CM 4SB2 Guía de solución de problemas
