Allied GS2450 Manual de usuario
Allied Vision Technologies Canada Inc.
101-3750 North Fraser Way
Burnaby, BC
V5J 5E9 / Canada
GS2450
/
GS2450C
Technical Manual
700050A
Updated September 17, 2010
GS2450 Technical Manual Page 2
Table of Contents
Table of Contents .......................................................................................................... ii
Introduction ............................................................................................................ 5
Precautions.............................................................................................................. 5
Warranty ................................................................................................................. 5
Specifications .......................................................................................................... 6
Supported Features ................................................................................................... 7
Mechanical .............................................................................................................. 8
Connections............................................................................................................. 9
Cleaning the Sensor..................................................................................................13
Adjusting the C-mount ..............................................................................................14
Camera Installation..................................................................................................15
System Optimization.................................................................................................20
Trouble Shooting .....................................................................................................22
Addendum..................................................................................................................23
GS IO Schematic.......................................................................................................24
Isolated Trigger Schematic.........................................................................................25
Non-isolated Trigger Schematic ..................................................................................26
Video Iris Schematic .................................................................................................27
Trigger Timing Diagram .............................................................................................28
Notes on Triggering ..................................................................................................29
GS2450 Technical Manual Page 3
Legal notice
For customers in the U.S.A.
(FCC Compliance Information)
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. However there is no guarantee
that interferences will not occur in a particular installation. Operation of this equipment in a residential environment is likely to
cause harmful interference.
You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this
equipment. The shielded interface cable recommended in this manual must be used with this equipment in order to comply with the
limits for a computing device pursuant to Subpart B of Part 15 of FCC Rules.
For customers in Canada
This digital apparatus complies with the Class A limits for radio noise emissions set out in the Radio Interference Regulations.
Pour utilisateurs au Canada
Cet appareil numérique est conforme aux normes classe A pour bruits radioélectriques, spécifiées dans le Règlement sur le
brouillage radioélectrique.
Life support applications
These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can
reasonably be expected to result in personal injury. Allied Vision Technologies customers using or selling these products for use in
such applications do so at their own risk and agree to fully indemnify Allied Vision Technologies for any damages resulting from
such improper use or sale.
Trademarks
Unless stated otherwise, all trademarks appearing in this document are the property of Allied Vision Technologies and are fully
protected by law.
Warranty
The information provided by Allied Vision Technologies is supplied without any guarantees or warranty whatsoever, be it specific or
implicit. Also excluded are all implicit warranties concerning the negotiability, the suitability for specific applications or the non-
breaking of laws and patents. Even if we assume that the information supplied to us is accurate, errors and inaccuracy may still
occur.
Copyright
All text, pictures and graphics are protected by copyright and other laws protecting intellectual property. It is not permitted to copy
or modify them for trade use or transfer, nor may they be used on web sites.
Allied Vision Technologies Canada Inc. 1/2010
All rights reserved.
GS2450 Technical Manual Page 4
Contacting Allied Vision Technologies
• Technical information:
http://www.alliedvisiontec.com
• Support:
Allied Vision Technologies GmbH (Headquarters)
Taschenweg 2a
07646 Stadtroda, Germany
Tel.: +49.36428.677-0
Fax.: +49.36428.677-28
e-mail: [email protected]
Allied Vision Technologies Canada Inc.
101-3750 North Fraser Way
Burnaby, BC, V5J 5E9, Canada
Tel: +1 604-875-8855
Fax: +1 604-875-8856
e-mail: [email protected]
Allied Vision Technologies Inc.
38 Washington Street
Newburyport, MA 01950, USA
Toll Free number +1-877-USA-1394
Tel.: +1 978-225-2030
Fax: +1 978-225-2029
e-mail: [email protected]
GS2450 Technical Manual Page 5
Introduction
The GB2450 series of cameras are 5 megapixel, 15 frames per second, Gigabit Ethernet cameras
based on the Sony ICX625ALA and ICX625AQA, Super HAD CCD sensors.
Precautions
READ INSTALLATION GUIDE CAREFULLY.
This document contains specific information which is necessary for the correct operation and
treatment of this product.
DO NOT OPEN THE CAMERA. WARRANTY IS VOID IF CAMERA IS OPENED.
This camera contains sensitive components which can be damaged if handled incorrectly.
KEEP SHIPPING MATERIAL.
Poor packaging of this product can cause damage during shipping.
VERIFY ALL EXTERNAL CONNECTIONS.
Verify all external connections in terms of voltage levels, power requirements, voltage polarity,
and signal integrity prior to powering this device.
CLEANING.
This product can be damaged by some volatile cleaning agents. Avoid cleaning the image sensor
unless absolutely necessary. Please see instructions on sensor cleaning in this document.
DO NOT EXCEED ENVIRONMENTAL SPECIFICATIONS.
See environmental specifications limits in the Specifications section of this document.
Warranty
AVT provides a 2 year warranty which covers the replacement and repair of all AVT parts which are
found to be defective in the normal use of this product. AVT will not warranty parts which have
been damaged through the obvious misuse of this product.
GS2450 Technical Manual Page 6
Specifications
Sensor Type Sony ICX625ALA CCD (ICX625AQA for color)
Sensor Shutter Type Progressive Interline
Image Resolution 2448 x 2050 pixels
Pixel Size 3.45μm x 3.45μm
Optical Forma
t
2
/
3 inch
Lens Moun
t
C-mount with adjustable back focus
Color Sensor Filter Pattern†Bayer
Full Resolution Frame Rate 15.1 fps
Frame Rate (1900 x 1080 ROI) 24.6 fps
I/O 1 isolated inpu
t
/
outpu
t
, 1 non-isolated input/output,
1 RS-232 input/output
Power Requirements Less than 3.8W†† (5V to 16V)†††
A/D 14 bi
t
Outpu
t
12 bi
t
Trigger latency* 2us for non-isolated I/O, 10us for isolated I/O
Trigger Jitter* ±20ns for non-isolated I/O, ±0.5us for isolated I/O
Tpd* 10ns for non-isolated I/O, 1.3us for isolated I/O
Operating Temperature 0 to 50 Celsius***
Operating Humidity 20 to 80% non-condensing
Weigh
t
186g
Hardware Interface Standard IEEE 802.3 1000BASE-T, 100BASE-TX
Software Interface Standard GigE Vision Standard 1.0
Regulator
y
CE, FCC, RoHS
† Applies to GS2450C only.
†† Power consumption will increase with reduced ROI imaging and color interpolation.
††† Nominal operating voltage is 12V. Cameras have been tested at 12V.
* See Notes on Triggering in the Addendum.
***DUE TO THE SMALL PACKAGING AND HIGH SPEED OF THE GS CAMERAS, SPECIAL CARE IS REQUIRED TO
MAINTAIN A REASONABLE OPERATING TEMPERATURE. IF THE CAMERA IS TO BE OPERATED IN A WARM
ENVIRONMENT, IT IS SUGGESTED THAT THE CAMERA BE MOUNTED ON A HEAT SINK SUCH AS A METAL BRACKET
AND THAT THERE IS SUFFICIENT AIR FLOW.
GS2450 Technical Manual Page 7
Supported Features
Imaging Modes free-running, external trigger, fixed rate, software trigger
Fixed Rate Control 0.001 fps to maximum frame rate
External Trigger Delay 0 to 60 seconds in 1 microsecond increments
External Trigger Even
t
rising edge, falling edge, any edge, level high, level low
Exposure Time 25 microseconds to 60 seconds in 1 microsecond increments
Gain 0 to 24dB
Region of Interest (ROI) independent x and y control with 1 pixel resolution
Horizontal Binning 1 to 8 pixels
Vertical Binning 1 to 8 rows
Pixel Formats Mono8, Mono16*, Bayer8, Bayer 16
Sync Out Modes trigger ready, trigger input, exposing, readout, imaging, strobe, GPO
*On monochrome versions only.
GS2450 Technical Manual Page 8
Mechanical
0.37 9.4
0.62 15.7
2.20 55.9
3.75 95.3
#1/4-20
2 PLCS TYP.
0.29 7.2
0.85 21.5
12
1.00 25.4
1.49 *37.9
M3 4MM DEEP
8 PLCS TYP.
ITEM 3
PIXEL 1,1
0.85 21.6
2.90 73.7
1.50 38
1.02 26
1.02 26
1.02 26
INCHES[MILLIMETERS]
ITEM 1: 3M 10214-55G3PC
ITEM 2: HALO HFJ11-1G16E-L12RL
ITEM 3: SONY ICX625
OPTIONS: LANDSCAPE/RIGHT ANGLE CONNECTORS
MODEL: GS2450/GS2450C
*Nominal for C mount. Add 0.3mm for color option.
GS2450 Technical Manual Page 9
Connections
1
342
Figure 1. GS SERIES connection diagram.
GS2450 Technical Manual Page 10
Item 1: GIGABIT ETHERNET PORT
This port conforms to the IEEE 802.3 1000BASE-T standard for Gigabit Ethernet over copper. It is
recommended that CAT5E or CAT6 compatible cabling and connectors be used for best
performance. Cable lengths up to 100m are supported.
Item 2: General Purpose I/O PORT
PIN 1PIN 7
PIN 8
PIN 14
PIN FUNCTION
112V POWER
2GND POWER
3Sync Input 1 - isolated
4Isolated Ground
5Sync Output 1 - isolated
6Video Iris
7DNC
812V POWER
9GND POWER
10 RS-232 TXD
11 RS-232 RXD
12 Sync Input 2 – non-isolated
13 Sync Ou
t
put 2 – non-isolated
Figure 2. General Purpose I/O Pin out. Camera rear
view. 14 GND SIGNAL
The General Purpose I/O port uses a 3M 10214-55G3PC (or 3M 10214-6212PC) connector on the
camera side. The mating cable connector is 3M 10114-3000PE with shielded housing 3M 10314-
3210-00X (X indicates color preference). This connector can be purchased from AVT or from
http://www.digikey.com.
See Addendum for more detail.
DO NOT EXCEED 5.5V ON SIGNAL INPUTS UNLESS OTHERWISE INDICATED. SYNC INPUT 1
CAN BE DRIVEN FROM A HIGHER VOLTAGE IF A CURRENT LIMITING RESISTOR IS USED TO
LIMIT THE CURRENT TO LESS THAN 10 MILLIAMPS.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Cámara de seguridad de Allied
Allied
Allied GC750 Manual de usuario
Allied
Allied GX1050 Manual de usuario
Allied
Allied GX1910 Manual de usuario
Allied
Allied Prosilica GC Series Manual de usuario
Allied
Allied AVT Prosilica GE Manual de usuario
Allied
Allied GC2450 Manual de usuario
Allied
Allied AVT Bigeye G Manual de usuario
Allied
Allied GS660 Manual de usuario
Allied
Allied AVT STINGRAY Manual de usuario
