Allied Telesis CAM Manual de usuario
CAM
Quick Install Guide
CAM Quick Install Guide
Document Number C613-04037-01 REV E.
© 2003-2007 Allied Telesis, Inc. All rights reserved. No part of this publication may be
reproduced without prior written permission from Allied Telesis, Inc.
Allied Telesis, Inc. reserves the right to make changes in specifications and other
information in this document without prior written notice. The information provided
herein is subject to change without notice. In no event shall Allied Telesis, Inc. be liable
for any incidental, special, indirect, or consequential damages whatsoever, including
but not limited to lost profits, arising out of or related to this manual or the information
contained herein, even if Allied Telesis, Inc. has been advised of, known, or should have
known, the possibility of such damages.
All company names, logos, and product designs that are trademarks or registered
trademarks are the property of their respective owners.
Quick Install Guide 3
C613-04037-01 REV E
Models Covered By This Guide
This Quick Install Guide contains information on installing the LineCAM
Content Addressable Memory (CAM) extender cards.
Package Contents
The following items are included with each CAM extender card. Contact your
sales representative if any items are damaged or missing.
■One CAM extender card.
■One CAM Quick Install Guide.
■Screws to secure CAM card to the base board’s mounting pillars.
■One warranty card.
Installing a CAM Extender Card
CAM should only be installed in AT-9800 Series switches by authorised service
personnel. Unauthorised opening of a switch’s lid may cause danger of injury
from electric shock, damage to the switch, and invalidation of the product
warranty.
One LineCAM extender card can be installed in each AT-9800 Series switch.
To install a LineCAM extender card in an AT-9800 Series switch:
1. Avoid injury by working in a safe environment.
The workspace should be free of hazards, and there should be sufficient
room to lay out the switch, CAM card, and tools.
2. Unpack the CAM card in an antistatic environment.
Do not attempt to install any hardware without observing correct antistatic
procedures. Failure to do so may damage the switch or CAM card. If you are
unsure what the correct procedures are, contact your authorised Allied Telesis
distributor or reseller.
3. If fitted, disconnect the switch’s redundant power supply.
4. Disconnect the mains power cord.
Before removing the switch’s lid, the power cord and, if connected, RPS power
cord should be disconnected to reduce risk of electrical shock.
5. Remove all interface cables.
4Content Addressable Memory (CAM)
C613-04037-01 REV E
6. Remove the switch’s lid.
The switch may need to be removed from any rack mounting system
before its lid can be removed.
Using a posidrive screwdriver, remove the 12 screws that secure the
switch’s lid. There are 5 screws located in countersunk holes on each side
of the lid, and 2 screws at the rear.
7. Align the CAM.
Position the CAM card over the CAM slot on the switch’s PCB. The three
support pillars located on the board should be aligned with the holes on
the CAM card, and the cards chamfers should be pointing to the switch’s
PSU (see Figure 1 on page 4).
Figure 1: AT-9800 Series CAM slot and pillar mounts.
8. Insert the CAM extender card.
Press the CAM card firmly into place. Secure the card to the support pillars
using the supplied screws.
The CAM card is now ready to test.
CAM mounts
Switch chip
CAM slot
BatteryCompact Flash
DIMM slot
CPU
Ports
Correct CAM
orientation
Chamfers
Quick Install Guide 5
C613-04037-01 REV E
Testing the CAM Extender Card
To check the switch has recognised the CAM card, turn on the switch and enter
the command:
show switch
to display system information, including the amount of CAM installed.
If there is no entry for the CAM, or the entry displays an unexpected value,
then the switch has not correctly detected the CAM’s presence. The most likely
cause is that the CAM card is not correctly plugged into the its slot. Repeat the
installation process, paying particular attention to the CAM card alignment
and insertion steps.
Use the show switch command again, and if the display is still not correct,
contact your authorised Allied Telesis distributor or reseller.
Where To Find More Information
Sources of further information:
■The Documentation and Tools CD-ROM bundled with your switch, which
contains the complete Documentation Set for your switch and its
expansion options, as well as tools for managing the switch.
■The Safety and Statutory Information Booklet for your switch, which
provides safety and statutory information for the switch and CAM card.
■The Hardware Reference for your switch, which provides detailed
information on switch and CAM card hardware features.
■The Software Reference for your switch, which provides detailed
information on configuring the switch and its software.
■www.alliedtelesis.com
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Hardware de computadora de Allied Telesis
Allied Telesis
Allied Telesis AT-B15/SX Manual de usuario
Allied Telesis
Allied Telesis AT-2814FX Manual de usuario
Allied Telesis
Allied Telesis AT-CV5M0 Series Manual de usuario
Allied Telesis
Allied Telesis AT-2874SX Manual de usuario
Allied Telesis
Allied Telesis AT-2500TX Manual de usuario
Allied Telesis
Allied Telesis AT-SPZX80 Manual de usuario
Allied Telesis
Allied Telesis AT-A15/SX Manual de usuario
Allied Telesis
Allied Telesis AT-SB4311 Manual de usuario
Allied Telesis
Allied Telesis AT-2812FX Manual de usuario
Allied Telesis
Allied Telesis AT-AR020 PRI E1/T1 Guía de aplicación
Manuales populares de Hardware de computadora de otras marcas
EMC2
EMC2 VNX Series Manual del propietario
Panasonic
Panasonic DV0PM20105 Manual de usuario
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manual de usuario
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manual de usuario
Raidon
Raidon iT2300 Manual de usuario
National Instruments
National Instruments PXI-8186 Manual de usuario
