Alliance Laundry Systems UW100TV Manual de usuario

Installation

www.alliancelaundry.com

Washer-Extractors

Pocket Hardmount

UniLinc

Refer to Page 5 for Model Numbers

PHM1400C

PHM1402C

150 Model

35 – 125 Models

Part No. F8138601R12

October 2012

Keep These Instructions for Future Reference.

(If this machine changes ownership, this manual must accompany machine.)

means without the expressed written consent of the publisher.

F8138601 1

Table of

Contents

Safety Information.............................................................................. 2

Explanation of Safety Messages........................................................... 2

Important Safety Instructions ............................................................... 2

Safety Decals ........................................................................................ 4

Operator Safety..................................................................................... 4

Introduction......................................................................................... 5

Model Identification ............................................................................. 5

Delivery Inspection............................................................................... 6

Name plate Location............................................................................. 6

Nameplate Location - UniLinc Models ........................................... 6

Replacement Parts ................................................................................ 6

Customer Service.................................................................................. 6

Specifications and Dimensions........................................................... 8

Machine Dimensions ............................................................................ 10

UWTV Models ................................................................................ 10

Machine Foundation Requirements...................................................... 13

Concrete Foundation Pad Installation................................................... 14

Floor Load Data ............................................................................... 16

Mounting Bolt Installation Requirements ............................................ 17

Machine Mounting and Grouting..................................................... 18

Mounting Bolt Hole Locations ............................................................. 19

Grout Placement ................................................................................... 24

Gap Setting for Vibration Switch .................................................... 25

Drain Connection Requirements........................................................... 29

Water Connection ................................................................................. 31

Electrical Installation Requirements..................................................... 33

Steam Requirements (Steam Heat Option Only).................................. 36

Chemical Injection Supply System....................................................... 37

External Supplies .................................................................................. 40

Chemical Injection Using Internal 24VAC Control Transformer ... 40

Chemical injection Using External AC Power Source .................... 41

External Supply Signals................................................................... 42

Safety Information

Explanation of Safety Messages

Precautionary statements (“DANGER,” “WARNING,”

and “CAUTION”), followed by specific instructions,

are found in this manual and on machine decals. These

precautions are intended for the personal safety of the

operator, user, servicer, and those maintaining the

machine.

Additional precautionary statements (“IMPORTANT”

and “NOTE”) are followed by specific instructions.

IMPORTANT: The word “IMPORTANT” is used

to inform the reader of specific procedures where

minor machine damage will occur if the procedure

is not followed.

NOTE: The word “NOTE” is used to communicate

installation, operation, maintenance or servicing

information that is important but not hazard

related.

Important Safety Instructions

1. Read all instructions before using the washer.

2. Install the washer according the

INSTALLATION instructions. Refer to the

GROUNDING instructions in the

INSTALLATION manual for the proper

grounding of the washer. All connections for

water, drain, electrical power and grounding must

comply with local codes and be made by licensed

personnel when required. It is recommended that

the machine be installed by qualified technicians.

3. Do not install or store the washer where it will be

exposed to water and/or weather.

4. To prevent fire and explosion, keep the area

around machine free from flammable and

combustible products. Do not add the following

substances or textiles containing traces of the

following substances to the wash water: gasoline,

kerosene, waxes, cooking oils, vegetable oils,

machine oils, dry-cleaning solvents, flammable

chemicals, thinners, or other flammable or

explosive substances. These substances give off

vapors that could ignite, explode or cause the

fabric to catch fire by itself.

5. Under certain conditions, hydrogen gas may be

produced in a hot water system that has not been

used for two weeks or more. HYDROGEN GAS

IS EXPLOSIVE. If the hot water system has not

been used for such a period, before using a

washing machine or combination washer-dryer,

turn on all hot water faucets and let the water

flow from each for several minutes. This will

release any accumulated hydrogen gas. The gas

is flammable, do not smoke or use an open flame

during this time.

6. To reduce the risk of an electric shock or fire, DO

NOT use an extension cord or an adapter to

connect the washer to the electrical power

source.

DANGER indicates an imminently

hazardous situation that, if not avoided,

will cause severe personal injury or

death.

DANGER

WARNING indicates a hazardous situation

that, if not avoided, could cause severe

personal injury or death.

WARNING

CAUTION indicates a hazardous situation

that, if not avoided, may cause minor or

moderate personal injury or property

damage.

CAUTION

To reduce the risk of fire, electric shock,

serious injury or death to persons when

using your washer, follow these basic

precautions:

W023

WARNING

Safety Information

F8138601

7. Do not allow children to play on or in the washer.

Close supervision of children is necessary when

the washer is used near children. This appliance

is not intended for use by young children or

infirm persons without supervision. Young

children should be supervised to ensure that they

do not play with the appliance. This is a safety

rule for all appliances.

8. DO NOT reach and/or climb into the tub or onto

the washer, ESPECIALLY if the wash drum is

moving. This is an imminently hazardous

situation that, if not avoided, will cause severe

personal injury or death.

9. Never operate the washer with any guards, panels

and/or parts removed or broken. DO NOT bypass

any safety devices or tamper with the controls.

10. Use washer only for its intended purpose,

washing textiles. Never wash machine parts or

automotive parts in the machine. This could

result in serious damage to the basket or tub.

11. Use only low-sudsing, no-foaming types of

commercial detergent. Be aware that hazardous

chemicals may be present. Wear hand and eye

protection when adding detergents and

chemicals. Always read and follow

manufacturer’s instructions on packages of

laundry and cleaning aids. Heed all warnings or

precautions. To reduce the risk of poisoning or

chemical burns, keep them out of the reach of

children at all times (preferably in a locked

cabinet).

12. Do not use fabric softeners or products to

eliminate static unless recommended by the

manufacturer of the fabric softener or product.

13. Always follow the fabric care instructions

supplied by the textile manufacturer.

14. Loading door MUST BE CLOSED any time the

washer is to fill, tumble or spin. DO NOT bypass

the loading door switch by permitting the washer

to operate with the loading door open. Do not

attempt to open the door until the washer has

drained and all moving parts have stopped.

15. Be aware that hot water is used to flush the

supply dispenser. Avoid opening the dispenser lid

while the machine is running.

16. Do not attach anything to the supply dispenser’s

nozzles, if applicable. The air gap must be

maintained.

17. Do not operate the machine without the water

reuse plug or water reuse system in place, if

applicable.

18. Be sure water connections have a shut-off valve

and that fill hose connections are tight. CLOSE

the shut-off valves at the end of each wash day.

19. Keep washer in good condition. Bumping or

dropping the washer can damage safety features.

If this occurs, have washer checked by a

qualified service person.

20. DANGER: Before inspecting or servicing

machine, power supply must be turned OFF. The

servicer needs to wait for at least 3 minutes after

turning the power OFF and needs to check for

residual voltage with a voltage meter. The

inverter capacitor or EMC filter remains charged

with high voltage for some time after powering

OFF. This is an imminently hazardous situation

that, if not avoided, will cause severe personal

injury or death.

21. Do not repair or replace any part of the washer, or

attempt any servicing unless specifically

recommended in the user-maintenance

instructions or in published user-repair

instructions that the user understands and has the

skills to carry out. ALWAYS disconnect the

washer from electrical, power and water supplies

before attempting any service.

22. Disconnect the power cord by grasping the plug,

not the cord. Replace worn power cords and/or

loose plugs. If the supply cord is damaged, it

must be replaced by a special cord or assembly

available from the service agent.

23. Before the washer is removed from service or

discarded, remove the door to the washing

compartment.

24. Failure to install, maintain, and/or operate this

washer according to the manufacturer’s

instructions may result in conditions which can

produce bodily injury and/or property damage.

NOTE: The WARNINGS and IMPORTANT

SAFETY INSTRUCTIONS appearing in this

manual are not meant to cover all possible

conditions and situations that may occur. Common

sense, caution and care must be exercised when

installing, maintaining, or operating the washer.

Any problems or conditions not understood should be

reported to the dealer, distributor, service agent or the

manufacturer.

Safety Information

F8138601

IMPORTANT: Ensure that the recommended

clearances for inspection and maintenance are

provided. Never allow the inspection and

maintenance space to be blocked.

Safety Decals

Safety decals appear at crucial locations on the

machine. Failure to maintain legible safety decals

could result in injury to the operator or service

technician.

Use manufacturer-authorized spare parts to avoid

safety hazards.

Operator Safety

The following maintenance checks must be performed

daily:

1. Verify that all warning labels are present and

legible, replace as necessary.

2. Check door interlock before starting operation of

the machine:

a. Attempt to start the machine with the door

open. The machine should not start.

b. Close the door without locking it and start the

machine. The machine should not start.

c. Attempt to open the door while a cycle is in

progress. The door should not open.

If the door lock and interlock are not functioning

properly, disconnect power and call a service

technician.

3. Do not attempt to operate the machine if any of

the following conditions are present:

a. The door does not remain securely locked

during the entire cycle.

b. Excessively high water level is evident.

c. Machine is not connected to a properly

grounded circuit.

This machine must be installed, adjusted,

and serviced by qualified electrical

maintenance personnel familiar with the

construction and operation of this type of

machinery. They must also be familiar

with the potential hazards involved.

Failure to observe this warning may result

in personal injury and/or equipment

damage, and may void the warranty.

SW004

WARNING

Never touch internal or external steam

pipes, connections, or components.

These surfaces can be extremely hot and

will cause severe burns. The steam must

be turned off and the pipe, connections,

and components allowed to cool before

the pipe can be touched.

SW014

WARNING

NEVER insert hands or objects into

basket until it has completely stopped.

Doing so could result in serious injury.

SW012

WARNING

Operating the machine with severe out-of-

balance loads could result in personal

injury and serious equipment damage.

W728

WARNING

F8138601

Introduction

Model Identification

Information in this manual is applicable to these

models:

UW35TV

UW60TV

UW80TV

UW100TV

UW125TV

UW150TV

Introduction

F8138601

This manual is designed as a guide to the installation

of the Pocket Hardmount washer-extractor.

NOTE: All information, illustrations, and

specifications contained in this manual are based

on the latest product information available at the

time of printing. We reserve the right to make

changes at any time without notice.

IMPORTANT: Warranty is void unless washer-

extractor is installed according to instructions in

this manual. Installation should comply with

minimum specifications and requirements, and

with applicable municipal building codes, water

supply regulations, electrical wiring regulations

and any other relevant statuary regulations. Due to

varied requirements, applicable local codes should

be thoroughly understood and all pre-installation

work arranged for accordingly.

Delivery Inspection

Upon delivery, visually inspect crate, protective cover,

and unit for any visible shipping damage. If the crate,

protective cover, or unit is damaged or signs of

possible damage are evident, have the carrier note the

condition on the shipping papers before the shipping

receipt is signed, or advise the carrier of the condition

as soon as it is discovered.

Remove the crate and protective cover as soon after

delivery as possible. If any damage is discovered upon

removal of the crate and/or protective cover, advise the

carrier and file a written claim immediately.

Name plate Location

The nameplate is located on the back of the machine.

Always provide the machine’s serial number and

model number when ordering parts or when seeking

technical assistance. Refer to Figure 1 and Figure 2.

Nameplate Location - UniLinc Models

On UniLinc models, nameplate information is also

programmed into the control. To access machine ID

through the control:

1. Press and hold , then , then

keypads at the same time.

2. Press the keypad until Diagnostic is

highlighted.

3. Press the keypad.

4. Press the keypad until machine ID is

highlighted.

5. Press the keypad.

Always provide the machine’s serial number and

model number when ordering parts or when seeking

technical assistance. Refer to Figure 1.

Figure 1

Replacement Parts

If literature or replacement parts are required, contact

the source from which the washer-extractor was

purchased or contact Alliance Laundry Systems LLC

at (920) 748-3950 for the name of the nearest

authorized parts distributor. A parts manual may be

ordered by returning the reply card provided with each

washer-extractor.

Customer Service

For technical assistance, contact your local distributor

or call:

(920) 748-3121

Ripon, Wisconsin

A record of each washer-extractor is on file with the

manufacturer. Always provide the machine’s serial

number and model number when ordering parts or

when seeking technical assistance. Refer to Figure 1

and Figure 2.

PHM1400C

1In Control (UniLinc Models)

2At Back of Machine

PHM1400C

MODEL EXAMPLE OF NAMEPLATE LOCATION

Introduction

F8138601

Figure 2

Model Number Familiarization Guide

Sample Model Number: UW60TVQU10001

UW Model Number Prefix

60 Washer-Extractor Capacity (60 pounds dry weight of laundry)

TType of Electrical Control T = UniLinc Control

VWasher-Extractor Speed Capabilities V = 8 Speeds

QElectrical Characteristics Refer to Table 7.

U1 Design Series

0001 Option Identification (varies from machine to machine)

PHM697N

UW060TVQU10001

00000000000

500000

200 – 240

50 – 60 3 3

60 27 720

EXAMPLE OF SERIAL PLATE

Specifications and Dimensions

Specifications 35 60 80 100 125 150

Overall Dimensions

Overall width, in (mm) 32.5 (826) 36.625 (930) 41.5 (1054) 41.5 (1054) 48 (1219) 50.25 (1277)

Overall height, in (mm) 55.5 (1410) 64.5 (1638) 68.5 (1740) 68.5 (1740) 72 (1829) 79 (2007)

Overall depth, in (mm) 43.625 (1108) 45 (1143) 51.5 (1308) 54.5 (1384) 58 (1473) 63 (1600)

Weight And Shipping Information

Net weight, lb (kg) 1030 (468) 1300 (590) 1730 (785) 1770 (805) 2420 (1100) 2970 (1347)

Basket Weight, lb (kg) 150 (68) 200 (92) 330 (150) 360 (163) 550 (250) 572 (260)*

Domestic shipping weight, lb (kg) 1085 (493) 1340 (608) 1795 (814) 1835 (832) 2525 (1148) 3022 (1371)

Domestic shipping volume,

ft3(m3)

66 (1.9) 84 (2.4) 119 (3.4) 119 (3.4) 166 (4.7) 172 (4.87)

Domestic shipping dimensions,

WxDxH, in (mm)

38x47x64

(970x1200x

1630)

40x49x74.5

(1016x1245x

1892)

44x60.5 x77.25

(1118x1537x

1962)

44x60.5x77.25

(1118x1537x

1962)

61.5x60x77.75

(1560x1520x

1980)

54.5x69x79

(139x176x

201)

Export shipping weight, lb (kg) 1150 (522) 1464 (664) 1990 (903) 2030 (921) 2800 (1270) 3350 (1520)

Export shipping volume, ft3(m3) 78 (2.2) 96 (2.7) 134 (3.8) 134 (3.8) 184 (5.3) 220 (6.3)

Export shipping dimensions,

WxDxH, in (mm)

41x50x65.5

(1050x1280x

1670)

43x52.125x74.5

(1092x1324x

1892)

47x63.5x77.25

(1194x1613x

1962)

47x63.5x77.25

(1194x1613x

1962)

63.5x63x80

(1620x1610x

2030)

61.5x71x87

(1562x1804x

2210)

Wash Cylinder Information

Cylinder diameter, in (mm) 26.25 (667) 32 (813) 36 (914) 36 (914) 42 (1067) 43 (1093)

Cylinder depth, in (mm) 18.375 (467) 20 (508) 21 (533) 27 (686) 24 (610) 27.8125 (706)

Cylinder volume, ft3(l) 5.76 (163) 9.31 (264) 12.4 (350) 15.9 (450) 19.2 (544) 23.4 (662)

Perforation size, in (mm) 0.1875 (4.8) 0.1875 (4.8) 0.1875 (4.8) 0.1875 (4.8) 0.1875 (4.8) 0.1875 (4.8)

Perforation open area, % 18 22 23 23 24 21.5

Door Opening Information

Door opening size, in (mm) 14.375 (365) 17.5 (445) 17.5 (445) 17.5 (445) 20 (508) 24.75 (629)

Height of door bottom above floor,

in (mm)

23.75 (603) 28.25 (718) 29 (737) 29 (737) 29 (737) 32 (813)

Drive Train Information

Number of motors in drivetrain111111

Drive motor power, hp (kW) 5.0 (3.7) 5.0 (3.7) 7.5 (5.6) 7.5 (5.6) 10 (7.5) 10 (7.5)

* Basket Only

(Continued)

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Arandela de Alliance Laundry Systems

Alliance Laundry Systems

Alliance Laundry Systems Home Laundry Automatic Washer Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems HFNNERSP116CW01 Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems Speed Queen TC5000WN Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems HCD020GD2 Guía de solución de problemas

Alliance Laundry Systems

Alliance Laundry Systems UW POCKET HARDMOUNT UW35B2 Guía de solución de problemas

Alliance Laundry Systems

Alliance Laundry Systems TLW22C_SVG Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems V-Series Guía de solución de problemas

Alliance Laundry Systems

Alliance Laundry Systems H002C Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems UX55PVXF6 Manual del propietario

Alliance Laundry Systems

Alliance Laundry Systems 201932R5 Guía

Alliance Laundry Systems

Alliance Laundry Systems UM202 Series Manual del propietario

Alliance Laundry Systems

Alliance Laundry Systems HWF261*E Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems AFB50RSP111TW01 Instrucciones de funcionamiento

Alliance Laundry Systems

Alliance Laundry Systems CL9163 Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems F232157R7 Manual del propietario

Alliance Laundry Systems

Alliance Laundry Systems HWF261*E Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems PHM1401C Manual del propietario

Alliance Laundry Systems

Alliance Laundry Systems AWN43RSN115CW01 Instrucciones de funcionamiento

Alliance Laundry Systems

Alliance Laundry Systems CCN020HNF Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems 800138R2 Manual del propietario

Alliance Laundry Systems

Alliance Laundry Systems AWNE8RSN115FW01 Instrucciones de funcionamiento

Alliance Laundry Systems

Alliance Laundry Systems CCN020HNF Manual del propietario

Alliance Laundry Systems

Alliance Laundry Systems AFBE9BSP303NN29 Instrucciones de funcionamiento

Alliance Laundry Systems

Alliance Laundry Systems HFNKCASG113TN01 Manual de usuario

Manuales populares de Arandela de otras marcas

Tricity Bendix

Tricity Bendix AW 1000 W Guía del producto

Panasonic

Panasonic NA-F60L5WRB Manual de usuario

GE WSLP1500 Manual

Electrolux

Electrolux EWF1284EDW Manual de usuario

Bosch

Bosch WAN2829BSN Manual de usuario

LG TV2516DV3B Manual de usuario

LG TH2517DSAV Manual de usuario

VESTEL

VESTEL CMH-XL 7510 TE Manual de usuario

AEG

AEG 74335 Manual de operación

Johnson

Johnson JWF721A Manual de usuario

Beko

Beko WTE7604XLW0 Manual de usuario

Danby

Danby DTT100A1WDB Instrucciones de montaje

Amica

Amica WA 14 Ex Manual de usuario

Daewoo

Daewoo DWD-F1222 Manual de usuario

Bosch

Bosch WAS28461AU Manual de usuario

Miele

Miele PW 6080 Vario Manual de usuario

Finlux

Finlux FLX108CF220 Manual de usuario

Whirlpool

Whirlpool 3LBR5132AN0 Manual de usuario