Allen AR16 Guía de aplicación

Power Buggy

055838; 03/12

AR16 and AR21

OPERATIONS-PARTS

MANUAL

055838; 03/12

This manual, or a copy of it, must be kept with the machine at all times.

There is a manual storage container located on the machine for your

convenience.

055838; 03/12

Power Buggy

OPERATIONS-PARTS MANUAL

All information, specifications, and illustrations in this manual are subject to change without notice and are based

on the latest information at the time of publication. No part of this manual may be reproduced or transmitted in any

form or by any means, electronics or mechanical, for any purpose, without the express written permission of Allen

Engineering Corporation (AEC). AEC assumes no responsibility or liability for any errors or inaccuracies that may

appear in this manual.

Allen Products are covered under one or more of the following patent numbers:

U.S. Design Patents: 344,736; 400,542; 400,544; 402,998; 402,999; 403,332; 404,041; 404,042; 410,931;

413,127; 416,564; 465,897; 466,909; 474,203.

U.S. Utility Patents: 5,108,220; 5,238,323; 5,328,295; 5,352,063; 5,405,216; 5,476,342; 5,480,257; 5,480,258;

5,533,831; 5,562,361; 5,567,075; 5,613,801; 5,658,089; 5,685,667; 5,803,658; 5,816,739; 5,816,740; 5,890,833;

5,934,823; 5,967,696; 5,988,938; 5,988,939; 6,019,433; 6,019,545; 6,048,130; 6,053,660; 6,089,786; 6,106,193;

6,857,815; 5,288,166; 6,582,153 B1, 7,108,449; 7,114,876; 7,316,523; 7,690,864 B2

Canadian Patents: 2,039,893.

First Issue: March 2012

Amended: February 2016

AEC Manual Part No.: 055838

Printed in U.S.A.

This manual covers the products listed below:

Part No.

058806

058807

058808

058801

058802

058809

058810

058803

058813

Description

BUGGY AR16 POLY BUCKET 13HPR NON FILL

BUGGY AR16 POLY BUCKET 13HPE NON FILL

BUGGY AR21 POLY BUCKET 20HPE NON FILL

BUGGY AR16 POLY BUCKET 13HPR FOAM

BUGGY AR16 POLY BUCKET 13HPE FOAM

BUGGY AR16 STEEL BUCKET 13HP RECOIL

BUGGY AR16 STEEL BUCKET 13HP ELEC

BUGGY AR21 POLY BUCKET 20HPE FOAM

BUGGY AR21 STEEL BUCKET 20HPE FOAM

064880 BUGGY AR16 POLY BUCKET PROPANE

ii 055838; 03/12

Limited Warranty

Allen Engineering Corporation (“Allen”) warrants its products to be free of defects in material or workmanship for:

TWO YEARS FROM END USER’S DATE OF PURCHASE

Warranty period begins on the date of purchase by the End User of the product. All warranty is based on the following

limited warranty terms and conditions, including the disclaimer of implied warranties and consequential damages.

1. Allen’s obligation and liability under this warranty is limited to repairing or replacing parts if, after Allen’s inspection,

there is determined to be a defect in material or workmanship. Allen reserves the choice to repair or replace.

2. If Allen chooses to replace the part, it will be at no cost to the customer and will be made available to the Allen

Distributor, Dealer, or Rental Center from whom the End User purchased the product.

3. Replacement or repair parts, installed in the product, are warranted only for the remainder of warranty period of the

product as though they were the original parts.

4. Allen does not warranty engines or batteries. Engine warranty claims should be made directly to an authorized factory

service center for the particular engine manufacturer. Batteries are not warranted due to unknown treatment during

transport, etc, and any battery claims should be directed to the battery manufacturer.

5. Allen’s warranty does not cover the normal maintenance of products or its components (such as engine tuneups and

oil & filter changes). The warranty also does not cover normal wear and tear items (such as belts and consumables).

6. Allen’s warranty will be void if it is determined that the defect resulted from operator abuse, failure to perform normal

maintenance on the product, modification to product, alterations or repairs made to the product without the written

approval of Allen. Allen specifically excludes from warranty any damage to any trowels resulting from an impact to the

rotors.

7. Impact damage to gear boxes is not covered under the Allen warranty and is deemed customer abuse.

8. Allen will pay shop labor on warranty items at the Allen Shop Labor Rate in existence on the date of the warranty

claim. An Allen labor chart will determine the time allowed to complete a repair and will govern the shop labor hours that

will be allowed.

9. Allen will pay freight on warranty replacement parts at worldwide standard ground rates. No warranty replacement

parts will be shipped air freight at the expense of Allen. Allen only pays outbound freight charges when sending warranty

replacement parts to the customer via ground service. Allen does not pay any inbound freight. However, if Allen deter-

mines this to be a warranted item, only then will Allen reimburse the customer for inbound freight at standard ground

rates.

10. ALLEN ENGINEERING CORPORATION’S WARRANTY POLICY WILL NOT COVER THE FOLLOWING: TAXES;

SHOP SUPPLIES; ENVIRONMENTAL SURCHARGES; AIR FREIGHT; TRAVEL TIME; LOSS OF TIME; INCONVEN-

IENCE; LOSS OF RENTAL REVENUE; RENTAL COSTS OF EQUIPMENT USED TO REPLACE THE PRODUCT

BEING REPAIRED;

LOSS OF USE OF THE PRODUCT; COMMERCIAL LOSS; OR ANY OTHER CHARGES WHATSOEVER OR ANY LIA-

BILITIES FOR DIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGE OR DELAY.

11. ALLEN ENGINEERING CORPORATION MAKES NO OTHER WARRANTY, EXPRESSED OR IMPLIED. THIS LIM-

ITED WARRANTY IS IN LIEU OF THE WARRANTY OF MERCHANTABILITY AND FITNESS. THERE ARE NO OTHER

WARRANTIES THAT EXTEND BEYOND THE DESCRIPTION ON THIS DOCUMENT.

12. No Allen employee or representative is authorized to change this warranty in any way or grant any other warranty

unless such change is made in writing and signed by an officer of Allen Engineering Corporation.

1-1

055838; 03/12

SECTION 1

SAFETY

Section 1

SAFETY

1-2

SECTION 1

SAFETY

055838; 03/12

CALIFORNIA PROPOSITION 65

WARNING

Gasoline engine exhaust from this product contains chemicals

known to the State of California to cause cancer, birth defects and

other reproductive harm.

State Regulations

1-3

055838; 03/12

SECTION 1

SAFETY

Federal Regulations

SILICOSIS WARNING

Grinding/cutting/drilling of masonry, concrete, metal and other

materials with silica in their composition may give off dust or

mists containing crystalline silica. Silica is a basic component

of sand, quartz, brick clay, granite and numerous other miner-

als and rocks. Repeated and/or substantial inhalation of air-

borne crystalline silica can cause serious or fatal respiratory

diseases, including silicosis. In addition, California and some

other authorities have listed respirable crystalline silica as a

substance known to cause cancer. When cutting such materi-

als, always follow the respiratory precautions mentioned

above.

RESPIRATORY HAZARDS

Grinding/cutting/drilling of masonry, concrete, metal and other

materials can generate dust, mists and fumes containing

chemicals known to cause serious or fatal injury or illness,

such as respiratory disease, cancer, birth defects or other

reproductive harm. If you are unfamiliar with the risks associ-

ated with the particular process and/or material being cut or

the composition of the tool being used, review the material

safety data sheet and/or consult your employer, the material

manufacturer/supplier, governmental agencies such as OSHA

and NIOSH and other sources on hazardous materials.

California and some other authorities, for instance, have pub-

lished lists of substances known to cause cancer, reproduc-

tive toxicity, or other harmful effects.

Control dust, mist and fumes at the source where possible. In

this regard use good work practices and follow the recom-

mendations of the manufacturers or suppliers, OSHA/NIOSH,

and occupational and trade associations. Water should be

used for dust suppression when wet cutting is feasible. When

the hazards from inhalation of dust, mists and fumes cannot

be eliminated, the operator and any bystanders should

always wear a respirator approved by NIOSH/MSHA for the

materials being used.

1-4

SECTION 1

SAFETY

055838; 03/12

1.1

General Safety Precautions

1.1.1 Safety-Alert Signs

This manual contains Safety-Alert Signs, as defined below, which must be followed to

reduce the possibility of improper service damage to the equipment or personal

injury. Read and follow all Safety-Alert Signs included in this manual.

NOTE defines an operating procedure,

condition, etc. which is essential to

highlight that contains useful or

important information.

EMERGENCY is used for the identification of safety equipment,

first aid, or emergency egress locations.

NOTICE used to convey safety information on labels and signs.

CAUTION is indicative of a potentially hazardous situation which,

if not avoided, may result in minor or moderate injury.

Potentially hazardous situations that could result in death

or serious injury are indicated by the word WARNING.

DANGER indicates an imminently hazardous situation which,

if not avoided, will result in death or serious injury.

1-5

055838; 03/12

SECTION 1

SAFETY

1.2

Spark Arrestor Notice

1.2.1 Laws Pertaining to Spark Arrestors

Some states require that in certain locations arrestors be used on internal

combustion engines. A spark arrester is a device designed to prevent the discharge

of spark or flames from the engine exhaust. It is often required when operating

equipment on forested land to prevent the risk of fires. Consult the engine distributor

or local authorities and make sure that you comply with regulations regarding spark

arrestors.

1-6

SECTION 1

SAFETY

055838; 03/12

A) General Safety

Familiarity and proper training are required for the safe operation of this equipment! Equipment

operated improperly or by untrained personnel can be dangerous! Read the operating instruc-

tions contained in both this manual and the engine manual and familiarize yourself with the loca-

tion and proper use of all controls. These safety and operating instructions for power buggies are

for your protection. Careless disregard of these instructions and other construction practices

could result in accidents and injury.

This machine is equipped with instructional and safety labels. Should any of

these labels become destroyed, faded, or otherwise illegible, replace them at

once. These labels can be purchased from an AEC dealer in your trade area. Should you need

the name of a dealer in your area, call Allen Engineering at 800-643-0095 or email customerser-

[email protected].

All repairs to this machine must be made by a qualified service mechanic

using only Allen Engineering replacement parts or their approved equal. Any

deviation from the original AEC supplied machine in the operation, repair, and/or modifications of

the machine without the express written consent of AEC, voids all machine warranties and any

liability for injuries and/or damage to person or property.

B) Before putting this equipment into operation inspect the equipment daily.

Inspect this equipment on a hard and level surface with proper lighting and ventilation, away from

pedestrian and vehicle traffic. Place Fire Protection equipment/Extinguishers in Inspection Area.

1. Shut engine off. Remove Ignition Key if so equipped.

2. Disconnect spark plug wire(s) to prevent accidental starts.

3. Block wheels in both directions to prevent machine movement.

4. Perform a detailed inspection of the following systems:

a) Speed Control Cable. This cable connects the speed control lever to the

hydrostatic transmission. With all linkage fully assembled cable travel should be

smooth and easy. Approximately 15 lbs. of pressure should be required to depress the

speed control lever at the handlebar. Lever should snap back briskly when it is

released. Cable should be free of cuts, kinks, binds and sharp bends. Rubber seals to

prevent entry of contamination should be intact at both cable ends. Due to the critical

nature of this part, replacement is recommended every 24 months or sooner for severe

service.

b) Speed control return spring. This spring is mounted on the transmission shift bar and

allows the speed control lever to return automatically when released. Spring tension

should be sufficient to briskly snap back the speed control lever when it is released.

Broken, damaged, or deformed springs must be replaced immediately. Note: never

1.3

General Safety

Otros manuales para AR16

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de Equipos para césped y jardín de otras marcas

Vertex

Vertex 1/3 HP Especificaciones técnicas

GHE

GHE AeroFlo 80 Manual de usuario

Millcreek

Millcreek 406 Manual de usuario

Land Pride

Land Pride Post Hole Diggers HD25 Manual de usuario

extraspace

extraspace GardenStore Manual de usuario

Yazoo/Kees

Yazoo/Kees Z9 Commercial Collection System Z9A Manual de programación

Premier designs

Premier designs WindGarden 26829 Manual de usuario

Snapper

Snapper 1691351 Manual de usuario

Mosquito Magnet

Mosquito Magnet Patriot Manual de usuario

Perfect

Perfect BG2 Manual de usuario

P.Lindberg

P.Lindberg LS2 Manual de usuario

Gardena

Gardena Easy 1887 Manual de usuario

Makita

Makita UM104D Manual de usuario

AQUA FLOW

AQUA FLOW PNRAD Manual de usuario

Tru-Turf

Tru-Turf RB48-11A Golf Green Roller Guía del usuario

BIOGROD

BIOGROD 730710 Manual de usuario

Land Pride

Land Pride RCF2784 Manual de usuario

Makita

Makita UM110D Manual de usuario

allen AR16 Guía de aplicación

Manuales populares de Equipos para césped y jardín de otras marcas