Allen-Bradley TLSZR/L-GD Manual de usuario
Installation Instructions
Original Instructions
TLSZR/L-GD2 Guard Locking Switch
IMPORTANT Do not attempt to install this device unless the installation instructions have been studied and
understood. This installation instruction sheet is available in some languages at
www.rockwellautomation.com/literature.
Select publication language and type “TLSZR/L-GD2” in the search field.
IMPORTANT Ne pas tenter pas d'installer ce dispositif sans avoir étudié et compris les instructions
d'installation. Cette notice d'installation est disponible dans certaines langues sur le site
www.rockwellautomation.com/literature. Sélectionner la langue de la publication et saisir «
TLSZR/L-GD2 » dans le champ de recherche.
WICHTIG Versuchen Sie nicht, dieses Gerät zu installieren, bevor Sie die Installationsanleitung gelesen
und verstanden haben. Diese Installationsanleitung steht in mehreren Sprachen unter der
folgenden Adresse zur Verfügung:www.rockwellautomation.com/literature. Wählen Sie unter
"Publication Language" die entsprechende Sprache aus und geben Sie "TLSZR/L-GD2" in das
Suchfeld ein.
IMPORTANTE Non installare questo dispositivo senza prima avere letto e compreso le istruzioni per
l'installazione. Queste istruzioni per l'installazione sono disponibili per alcune lingue sul sito
www.rockwellautomation.com/literature. Selezionare la lingua della pubblicazione e digitare
"TLSZR/L-GD2" nel campo di ricerca.
IMPORTANTE Não instale esse dispositivo sem estudar e compreender as instruções de instalação. Essa folha
de instruções de instalação está disponível em algumas línguas em
www.rockwellautomation.com/literature. Selecione a língua de publicação e escreva "TLSZR/
L-GD2" no campo de pesquisa.
IMPORTANTE No instale este dispositivo sin estudiar y entender las instrucciones de instalación. Esta hoja de
instrucciones de instalación está disponible en algunos idiomas en
www.rockwellautomation.com/literature. Seleccione el idioma de publicación e ingrese
"TLSZR/L-GD2" en el campo de búsqueda.
Viktigt Läs monteringsanvisningen innan försök att installera enheten görs. Detta instruktionsblad
finns tillgängligt på olika språk på www.rockwellautomation.com/literature. Välj
publikationsspråk och ange typ: "TLSZR / L-GD2" i sökfältet.
2Rockwell Automation Publication 440G-IN007B-EN-P - September 2016
TLSZR/L-GD2 Guard Locking Switch
Table of Contents
Installation Instructions............................................................................................................................3
Technical Specifications ...........................................................................................................................4
OSSD Outputs and Pulse Testing ..................................................................................................5
Dimensions [mm (in.)]...............................................................................................................................6
Mounting Information [mm (in.)]..........................................................................................................7
Allowable Approach Directions.....................................................................................................8
Clearance in Closed Position [mm (in)] .......................................................................................8
Auxiliary/Manual Release [mm (in.)].............................................................................................8
Minimum Operating Radius [mm (in.)]........................................................................................9
Manual Override Key for Power-to-Release Version ..............................................................9
Mounting Restrictions.......................................................................................................................9
Connections...............................................................................................................................................10
Status/Diagnostic LED Indicator......................................................................................................... 10
Commissioning......................................................................................................................................... 11
“Multi-Time” Learn Process...........................................................................................................11
“One-Time” Learn Process............................................................................................................. 12
Status/Diagnostic LED Error Codes During the Learning Process.................................. 12
Functional Testing ........................................................................................................................... 12
Wiring Diagrams....................................................................................................................................... 14
Troubleshooting Series Circuit....................................................................................................14
Unit Response Time ........................................................................................................................15
Application Wiring Example ........................................................................................................16
Recommended Relays............................................................................................................................17
Maintenance.............................................................................................................................................. 17
Declaration of Conformity....................................................................................................................17
Rockwell Automation Publication 440G-IN007B-EN-P - September 2016 3
TLSZR/L-GD2 Guard Locking Switch
Installation Instructions
Installation must be in accordance with the following steps and stated specifications and
conducted by competent personnel. The unit is not to be used as a mechanical stop. Guard stops
and guides must be fitted. Adherence to the recommended maintenance instructions forms part
of the warranty.
This device is intended to be part of the safety-related control system of a machine. Before
installation, a risk assessment should be performed to determine whether the specifications of
this device are suitable for all foreseeable operational and environmental characteristics of the
machine to which it is to be fitted. See Technical Specifications for certification information and
ratings.
Use nonremovable screws, bolts, or nuts to mount the switch and actuators. Do not over torque
the mounting hardware.
For use with flexible actuator only, 440G-A27143.
TLS-Z guard locking switches are classified according to ISO 14119 as Type 4 switching
devices.The RFID targets are classified as having a high level of coding.
Measures are to be taken to minimize the need to defeat and to manage the use and availability of
spare RFID targets.
IMPORTANT SAVE THESE INSTRUCTIONS FOR FUTURE USE
ATTENTION: Guard locking switches that are activated by the power to lock principle,
440G-TZS21UPLH, must only be used after a risk assessment has shown that the use of a power to
release principle, 440G-TZSPRH, is inappropriate, since the guard can be immediately opened
after a loss of the power supply or upon activation of the unlocking signal.
Target
Actuator
TLSZR/L-GD2
Switch
Target
Alignment
Marks
4Rockwell Automation Publication 440G-IN007B-EN-P - September 2016
TLSZR/L-GD2 Guard Locking Switch
Technical Specifications
Safety Ratings
Standards IEC 60947-5-3, IEC 60947-5-1, IEC 61508, EN ISO 13849-1, ISO 14119
Safety Classification and Functional Safety Data
Safety Classification of the guard door position and lock monitoring function is
PLe, Category 4 to IEC 13949-1, IEC 61508.
For details, see the Rockwell Automation® Functional Safety Data Sheet:
http://literature.rockwellautomation.com/idc/groups/literature/documents/sr/
safety-sr001_-en-e.pdf
Certifications CE Marked for all applicable EU directives, cULus (UL 508), and TÜV.
Operating Characteristics
TLSZR-GD2 Power to release
TLSZL-GD2 Power to lock
Assured Locking Distance [mm (in.)] Maximum target distance: 13 (0.51)
Maximum clearance between actuator base and switch in the door-closed
position: 5 mm (0.2 in.) (See “Clearance in Closed Position [mm (in)]” on page 8)
Torque for M5 Mounting 1.4 Nm (12.39 lb-in.)
Torque for Cover Mounting 1.2 Nm (10.62 lb-in.)
Locking Force Fmax Plastic pins: 1950 N (488 lb) Steel bolts: 2600 N (585 lb)
Locking Force Fzh (with EN/ISO 14119) Plastic pins: 1500 N (337 lb) Steel bolts: 2000 N (450 lb)
Maximum Output Current (all outputs) 200 mA
Current Consumption - solenoid not energized (no load supply
current) 50 mA
Current Consumption - solenoid energized (no load supply
current) 120 mA (260 mA inrush)
Solenoid Duty Cycle 100%
Off-State Current < 0.5 mA DC
Maximum Number of Switches (connected in series) Unlimited. See “Unit Response Time” on page 15.
Operating Voltage Ue 24V DC +10% / -15%
Frequency of Operating Cycle 1 Hz maximum
Actuation Speed, Max. 160 mm (6.29 in.) per second
Actuation Speed, Min. 100 mm (3.94 in.) per minute
Response Time (Off) 75 ms first switch, 25 ms additional for each switch
Utilization Category (IEC 60947-5-2) DC-13 24V 200 mA
Impulse Withstand Voltage Uimp 250V
Pollution Degree 3
Protection Class 2
Mechanical Life 1 x 106 cycles
Environmental
Operating Temperature [C (F)] -10°…60° C (+14°…140° F)
Operating Humidity 5%…95% relative
Risk Time If the RFID door target moves outside of the operating distance, the safety outputs
are deactivated after a maximum of 60 ms
Rated Insulation Voltage Ui 500V
Rockwell Automation Publication 440G-IN007B-EN-P - September 2016 5
TLSZR/L-GD2 Guard Locking Switch
The device can be used under normal service conditions. Maximum altitude up to 2000 m
(6561.66 ft).
Voltage drop Vd 2V ma ximum
OSSD Outputs and Pulse Testing
The safety inputs are Safety A+ and Safety B+.
The OSSD outputs are Safety A and Safety B with the safe state defined as 0V (guard door open
or not locked).
The safety outputs use test pulses to detect short-circuit and cross-wire short detection. The
cross-short pulses are asynchronous of duration 0.1 ms repeating every 11 s and the short-circuit
pulses are synchronous of duration of 0.5 ms repeating every 11 s. The connected control system
must be tolerant of these pulses.
Enclosure Ingress Rating NEMA 3, 4X, 12, 13, IP66, IP67, IP69K
Shock and Vibration IEC 68-2-27 30 g, 11 ms/IEC 68-2-6 10…55Hz
Radio Frequency IEC 61000-4-3
IEC 61000-4-6
General
Housing Material UL approved glass filled PBT
Actuator Material Stainless Steel
Target Material UL approved glass filled PBT
Connection M12 8-pin connector
Protection (the outputs are short-circuit protected)
Short-circuit Protection Incorporated
Current Limitation Incorporated
Overload Protection Incorporated
False Pulse Protection Incorporated
Transient Noise Protection Incorporated
Reverse Polarity Protection Incorporated
Overvoltage Protection Incorporated
Thermal Shutdown/Restart Incorporated
Outputs (Guard door closed and locked)
Outputs Description Status
Safety 2 x PNP, 0.2 A max. ON (+24V DC)
Auxiliary 1 x PNP, 0.2 A max. OFF (0V DC)
Environmental
6Rockwell Automation Publication 440G-IN007B-EN-P - September 2016
TLSZR/L-GD2 Guard Locking Switch
Dimensions [mm (in.)]
86 (3.39)
57 (2.24)
3 (0.12)
3 (0.12)
6.5 (0.26)
17
(0.67)
21 (0.83)
14.5 (0.57)
52.5 (2.07)
31.5 (1.24)
60.5 (2.38)
67.5 (2.66)
6.5 (0.26)
5 (0.2)
M5 x 4
126 (4.96)
105 (4.13)
14 (0.55)
22 (0.87)
27 (1.06)
39 (1.54)
9 (0.35)
14 (0.55)
33 (1.3)
6.5 (0.26)
25.5 (1)
20.5 (0.81)
5 (0.2)
5.5 (0.22)
21
(0.83)
17 (0.67)
43 (1.69) 6 (0.24)
5 (0.2)
73 (2.87)
4 (0.16)
Status/
Diagnostic
LED
Target Alignment Mark
14
(0.55)
2.2 (0.09)
24
(0.94)
4.2 (0.17)
19.2 (0.76)
M12
18
(0.71)
20
(0.79)
8
(0.31)
40 (1.57)
31 (4.22)
6.8
(0.27)
4 x 5.5 (0.22)
2 x M3
19
(0.75)
13
(0.51)
51
(2.0)
52 (2.05)
Actuator
Use with flexible actuator only:
23.2 (0.91)
11.9
(0.47)
19
(0.75)
440G-ATZAE-
xxxx
29.3 (1.15)
7
(0.28)
20
(0.79)
M5
5.5
(0.22)
Target
Connector location and
dimensions
Do not use cable gland knockouts, two places
Rockwell Automation Publication 440G-IN007B-EN-P - September 2016 7
TLSZR/L-GD2 Guard Locking Switch
Mounting Information [mm (in.)]
1.2 N•m (10.62 lb•in.)
2 x M5
1.4 N•m (12.39 lb•in.)
3 x M5
15 (0.59)
Steel bolts
Plastic pins
Fzh = 2000 N (450 lb)
Fzh = 1500 N (337 lb)
5 (0.20)
dia.
2 x M5
1.4 N•m
(12.39 lb•in.)
1.2 N•m (10.62 lb•in.)
5.5 (0.22)
6 (0.24)
20
(0.79)
86.5
(3.4)
35
(1.38)
40
(1.57)
13 (0.51) 19
(0.75)
6 (0.24)
7 (0.28)
180
Target
Actuator
8Rockwell Automation Publication 440G-IN007B-EN-P - September 2016
TLSZR/L-GD2 Guard Locking Switch
Allowable Approach Directions
Clearance in Closed Position [mm (in)]
(and Maximum Actuator Insertion Distance for Locking)
Auxiliary/Manual Release [mm (in.)]
A manual release is possible by removing the secure TorX screws and pressing the internal
mechanism.
The actuator and target should always be
mounted as “close coupled” and can approach
the switch in any of the three entry slot
positions shown.
Approach from the underside is not allowed.
2...5 (0.08...0.20)
Provide a separate mechanical stop to protect the
switch.
Minimum clearance: 2 (0.08).
Maximum assured locking distance: 5 (0.20).
IMPORTANT Do not use the switch as a guard stop.
T20
≤ 2.5 (0.098) dia.
1
3
2
2
If power is supplied to the switch and the
switch is in the locked state, operation of
the auxiliary release will cause the switch to
enter a fault condition (blinking red
LED).
To reset the switch, cycle the power.
Rockwell Automation Publication 440G-IN007B-EN-P - September 2016 9
TLSZR/L-GD2 Guard Locking Switch
Minimum Operating Radius [mm (in.)]
Minimum operating radius is for all planes of approach of the actuator key, both along the length
and perpendicular to the key. Use the two adjusting setscrews on the actuator to optimize the key
angle.
Manual Override Key for Power-to-Release Version
The cover with manual override key is intended for use with a power-to-release version
TLSZR-GD2. It provides an auxiliary release function for use when power is not available to
achieve automatic/electrical interlocking.
Mounting Restrictions
If a pair of TLS-Z switches are mounted close to each other, the two inductive fields will interact
causing crosstalk, which will result in nuisance faults and false operation.
An absolute minimum of 200 mm (8 in.) must be used to help ensure correct operation.
The above applies if a TLS-Z switch is mounted close to the 440G-LZ guard locking and the
440N-Z SensaGuard™ switches.
80 (3.19) 80 (3.19)80 (3.19)80 (3.19)
90°
1.2 N•m (10.62 lb•in)
1
2
90°
10 Rockwell Automation Publication 440G-IN007B-EN-P - September 2016
TLSZR/L-GD2 Guard Locking Switch
For Learn Process LED error codes, see page 12.
Connections
8-Pin Micro (M12)
Color Function Pin
8-Pin Cordset
889D-F8AB-*
or cable version
White Aux 1
Brown 24V DC+ 2
Green Lock 3
Yellow Safety B+ OSSD Input 4
Grey Safety A OSSD Output 5
Pink Safety B OSSD Output 6
Blue Gnd / 0V 7
Red Safety A+ OSSD Input 8
* Replace symbol with 2 (2 m), 5 (5 m), or 10 (10 m) for standard cable lengths.
Status/Diagnostic LED Indicator
Operating
Status/Diagnostic LED State Meaning
Solid Green Door/Guard closed and locked, safety outputs active.
Solid Red Door/Guard not locked, safety outputs off.
Blinking Red Unit failure. See Troubleshooting, below.
Blinking Green Door/Guard closed and locked, no input signal.
Troubleshooting
Status/Diagnostic LED State Status Troubleshooting
Off Not powered N/A
Solid Green OSSD on N/A
Solid Red OSSD not active N/A
Blinking Green Power up test
or
Safety inputs not present Check 24V DC or OSSD inputs (yellow and red wire)
Blinking Red 1 Hz Flash: Recoverable fault
4 Hz Flash: Non-recoverable fault
Recoverable fault: Check OSSD. Outputs are not shorted to GND,
24VDC, or each other. Cycle power.
Non-recoverable fault: Cycle power.
2 24V DC+
1 Aux
7 0V
6 Safety B
3 Lock Command
8 Safety A+
4 Safety B+
5 Safety A
Tabla de contenidos
Otros manuales de Cambiar de Allen-Bradley
Allen-Bradley
Allen-Bradley Stratix 8300 Manual de usuario
Allen-Bradley
Allen-Bradley 140M-SB Manual de usuario
Allen-Bradley
Allen-Bradley 140G-M-EOP Manual de usuario
Allen-Bradley
Allen-Bradley 140G-R Series Manual de usuario
Allen-Bradley
Allen-Bradley Stratix 5400 Manual de usuario
Allen-Bradley
Allen-Bradley 194L Manual de usuario
Allen-Bradley
Allen-Bradley armorstratix 5700 Manual de usuario
Allen-Bradley
Allen-Bradley 800T-NGCY Manual de usuario
Allen-Bradley
Allen-Bradley ferrogard gd2 Manual de usuario
Allen-Bradley
Allen-Bradley Guard master IMP Series Manual de usuario
Allen-Bradley
Allen-Bradley Stratix 2000 Manual de usuario
Allen-Bradley
Allen-Bradley 105-C09 Series Manual de usuario
Allen-Bradley
Allen-Bradley 194E Manual de usuario
Allen-Bradley
Allen-Bradley 105-PW23 Manual de usuario
Allen-Bradley
Allen-Bradley TLS-GD2 Manual de usuario
Allen-Bradley
Allen-Bradley 440G-LZ Manual de operación y mantenimiento
Allen-Bradley
Allen-Bradley 836T Manual de instrucciones
Allen-Bradley
Allen-Bradley Stratix 5400 Manual de usuario
Allen-Bradley
Allen-Bradley TLS-GD2 Manual de usuario
Allen-Bradley
Allen-Bradley Stratix 5400 Manual de usuario
