Allegion Falcon Series Manual de usuario

BEFORE ATTEMPTING TO INSTALL LOCK, READ ALL

INSTRUCTIONS AND LAY PARTS OUT AS SHOWN IN

FIGURE 7A OR 7B

BORE 1" HOLE (25mm)

PARALLEL TO

SIDES OF DOOR

CENTER

FOR 1³⁄₄"

DOORS

(44mm)

CENTER

FOR 1³⁄₈"

DOORS

(43mm)

FOLD ALONG EDGE OF DOOR

1¹⁄₂"

HOLE

1¹⁄₈" (28mm) MIN.

BEYOND REQUIRED BACKSET

DISTANCE

FROM EDGE

OF DOOR

(BACKSET)

IMPORTANT

PLACE TEMPLATE

ON HIGH EDGE

OF DOOR BEVEL

BORE 1¹⁄₂" (38mm) HOLE AT CORRECT BACKSET

2³⁄₄"

(70mm)

(127mm)

2³⁄₈"

(60mm)

Marking Template for New Installations

1 Mark centers for latch

holes and side holes (follow

template instructions)

2 Drill 1¹⁄₂" dia. hole in

face and 1" dia. hole in

edge of door per template

instructions

3 Insert latch in edge

keeping its face parallel to

face of door. Mark outline of

latch face and remove latch

4 Chisel 5\32" (3.97mm)

deep or until latch face

is flush with door edge.

5Insert latch and secure

with two (2) No. 7 x ³⁄₄" wood

screws. Tighten screws.

EXTENDED

Install with

A on Top

002103-000-70

Printed in U.S.A.

002103-000-70 Rev. 10/14-d

IMPORTANT: EXTEND DEADBOLT BEFORE PROCEEDING

6 TRIM ASSEMBLY

8. STRIKE INSTALLATION

STANDARD STRIKE

OPTIONAL STRIKE

Small rings (F) are used only on

1³⁄₈" thick doors

Install

keyed trims

as shown

(Key Notches Up)

Single Cylinder Screw ¹⁄₄" bolts (I) through plate* (H) into

housing (B) & tighten. Engage tailpiece (P) with thumbturn

(J). Fasten thumbturn (J) to plate (H) with short machine

screws (K)

NOTE Align plate with the large holes below the small holes

as shown

Double Cylinder Screw ¹⁄₄" bolts (J) through housing (H),

and ring (E) into housing (B) engaging tailpieces (P) with

the vertical slot in the deadbolt

Important: Check locking and unlocking of both sides

with door open before snapping covers (K) over bolts (J).

Place strike on

jamb, centering over

hole and parallel to

edge of frame. Mark

outline and remove

strike.

DChisel cutout ¹⁄₁₆"

deep for standard strike.

Chisel cutout ¹⁄₁₆" deep

for optional strike.

GInstall strike with

No. 7 x ³⁄₄" screws.

Tighten screws.

7A SINGLE CYLINDER

ASSEMBLY

Optional

Interchangeable Core

7B DOUBLE CYLINDER

ASSEMBLY

Optional

Interchangeable Core

DOOR

STOP

Screws (S)

(O) Screws

BBore 1" diameter hole

1¹⁄₈" deep centered

between the markings.

CAUTION: Deadbolt will

not function correctly if

hole is too shallow.

AMark the corners of the

deadbolt with crayon or

grease pencil. Retract

deadbolt and close door.

Throw dead bolt firmly

against jamb to transfer

markings.

FDrill 2 pilot holes (O) 3" deep to prevent splitting of jamb and

install 3" long screws (O) in large holes next to door jamb

ECenter strike (M) over hole with small holes (S) away

from door stop. Install 2 small screws (S).

Check locking function before installing longer screws.

4.250

3.125

Additional Notes: Revision History Revision Description:

D > Revised artwork

1. None A B C D E F

FAL 0790 6683

Material

50# oset or equivalent

Edited By Approved By EC Number Release Date

J. Ellis M. Roberts xxxxx 10/14

Notes

1. printed both sides

2. printed black

3. tolerance ± .13

4. printed in country may vary

5. barcode shows after folding

Title

Falcon Marking Template for New Installations

Creation Date

10-22-14

Number

002103-000-70

Revision

Created By

J. Ellis Activity

3899 Hancock Expwy

Security, CO 80911 © Allegion 2014Software: InDesign CS6

4.250

12.500

BEGINNING SHEET

FOLDED SHEET

FRONT

Tabla de contenidos

Otros manuales de Cerrar de Allegion

Allegion

Allegion BE369 Manual de operación y mantenimiento

Allegion

Allegion Falcon S Series Hoja de instrucciones

Allegion

Allegion Falcon 25-WDC Manual de usuario

Allegion

Allegion AD Series Manual de usuario

Allegion

Allegion Schlage F Series Manual de usuario

Allegion

Allegion Schlage DEADBOLT Manual de usuario

Allegion

Allegion interflex IF-261 Manual de usuario

Allegion

Allegion CISA 48816 Series Manual de usuario

Allegion

Allegion Dexter DB1000 Deadbolt Standard Guía

Allegion

Allegion Schlage S-480 Manual de usuario

Allegion

Allegion Von Duprin 4754 Manual de usuario

Allegion

Allegion Kryptonite 815 Combo Manual de usuario

Allegion

Allegion Schlage D Series Manual de usuario

Allegion

Allegion Schlage AD Series Manual de usuario

Allegion

Allegion FALCON LM Series Manual de usuario

Allegion

Allegion CISA MyEVO Manual de usuario

Allegion

Allegion Falcon F Series Manual de usuario

Allegion

Allegion AD-300 Manual de usuario

Allegion

Allegion Cisa Mito Sensor Manual de usuario

Allegion

Allegion Legge 990MF Manual de usuario

Allegion

Allegion Briton 9365-990 Manual de usuario

Allegion

Allegion SES20171127F Manual de usuario

Allegion

Allegion FALCON X571 Manual de usuario

Allegion

Allegion Olivari PT Series Manual de usuario

Manuales populares de Cerrar de otras marcas

Magic

Magic 105 Manual de usuario

Gantner

Gantner GAT NET.Lock 7020 System Guía rápida

Wittkopp

Wittkopp Insys 7202 Manual de usuario

Dorma

Dorma Studio Classic Manual de usuario

Securam

Securam ECSL-601 Manual de usuario

Sudhaus

Sudhaus 3003 Manual de usuario

Safety 1st

Safety 1st 48517 Manual de usuario

Pado

Pado FDS-10 Manual de usuario

Esco

Esco systeQ Series Manual de usuario

COMPX

COMPX National D8951 Manual de usuario

secureo

secureo Key Box Manual de usuario

Stock Loks

Stock Loks C8713 Manual de usuario

COMPX

COMPX 1T-058 Manual del propietario

Auslock

Auslock T11 Manual de usuario

ELCOM

ELCOM 7205 Manual de usuario

Stealth SAFES

Stealth SAFES ShadowVault Manual de usuario

Knox

Knox KeySecure 5 Manual de usuario

Kwikset

Kwikset 48334/01 Manual de usuario