Alderon Industries Sump Advisor 2000514 Manual de usuario

USER GUIDE

PART NUMBERS:

Sump Advisor™2-Zone Alarm and Sensor

Rated Type 1, Indoor Alarm Panel (use with Alderon™ VertiMAC™ series)

2000514 2000558 2000559

2000560 2000561

Alderon Industries™

Pat. No. 10,794,379

Contents

Introduction................................................................................................................................................................. 3

Safety Guidelines ................................................................................................................................................... 3

Product Included .................................................................................................................................................... 4

Features ................................................................................................................................................................. 5

Installation of Sump Advisor™ Alarm Panel ............................................................................................................... 6

9VDC Battery Backup ........................................................................................................................................ 6, 7

Mounting Alarm Panel............................................................................................................................................ 8

Wiring Auxiliary Dry Contacts .......................................................................................................................... 9, 10

Installation of Sump Advisor™ Sensor ..................................................................................................................... 10

Installation of VertiMAC™ Pump Switch (sold separately) ............................................................................................ 11

Pump Differential.................................................................................................................................................. 11

Mounting Pump Switch .............................................................................................................................12, 13, 14

Connecting Power to VertiMAC™ and Sump Advisor™........................................................................................... 15

VertiMAC™ Pump Switch with Sump Advisor™ Sensor...................................................................................... 15

Sump Advisor™ Alarm Panel............................................................................................................................... 15

Testing ................................................................................................................................................................ 16, 17

Assembly and Maintenance ..................................................................................................................................... 18

Additional Assembly and Product Information ......................................................................................... 18, 19, 20

Maintenance................................................................................................................................................... 20, 21

General Operation.................................................................................................................................................... 22

Sump Pump ......................................................................................................................................................... 22

Sump Pump with Indoor/Outdoor LED Strobe Beacon ........................................................................................ 23

Sump Pump with Auto Dialer ............................................................................................................................... 24

Sump Pump with Battery Backup ........................................................................................................................ 25

Sump Pump with Battery Backup and Auto Dialer............................................................................................... 26

Troubleshooting ........................................................................................................................................................ 27

Specications ........................................................................................................................................................... 28

Warranty Information ................................................................................................................................................ 29

Company Information ............................................................................................................................................... 32

Sump Advisor™ 2-Zone Alarm and Sensor - USER GUIDE

Alderon Industries™ - Leading Edge Control Products | 3

Sump Advisor™ 2-Zone Alarm and Sensor - USER GUIDE

Introduction

The Sump Advisor™ 2-Zone Alarm is an indoor rated alarm panel, powered by a standard 120VAC wall outlet. The included Sump

Advisor™ Sensor is attached to the top of the VertiMAC™ VM-Series pump switch (sold separately) and connected to the terminal

block on the alarm panel. The alarm panel and sensor can only be used with the Alderon™ VertiMAC™ pump switch series, a

oat operated pump switch system, typically used in sump pump applications or situations where a regular pump switch cannot

operate due to limited space. The innovative Sump Advisor™ sensor integrates high level alarm and pump run switches that are

connected to the Sump Advisor™ alarm panel. The alarm panel has a 9-volt battery backup (customer supplied) and auxiliary dry

contacts for high level alarm and pump run status that can be connected to a building automation system (BAS) or auto dialers.

Safety Guidelines

Before proceeding with the installation or operation of this product, read all instructions thoroughly, as well as complying with

all federal, state and local codes, regulations, and practices. This product must be installed by qualied personnel familiar with

all applicable local electrical and mechanical codes. Refer to the National Electrical Code (NFPA 70). Failure to properly install

and test this product can result in personal injury or equipment malfunction.

1. DISCONNECT POWER when installing or servicing the product. Failure to disconnect all power sources could result in

serious injury or death.

2. NEVER enter a ooded space without proper Personal Protective Equipment (PPE). Always wear dielectric rubber boots

and other applicable protective equipment when water is on the oor and you must service an energized pump, alarm

system, or product.

3. DO NOT enter the water if the water level is higher than that of the protection your PPE offers or if your PPE is not

watertight.

4. DO NOT use this product with or near ammable liquids.

5. DO NOT install this product in locations classied as hazardous or in explosive atmospheres as dened by any applicable

electrical safety code.

WARNING

4 | Alderon Industries™ - Leading Edge Control Products

Sump Advisor™ 2-Zone Alarm and Sensor - USER GUIDE

Product Included

(1) Sump Advisor™ 2-Zone Alarm Panel

The alarm panel provides local high level alarm and pump run

indication of the VertiMAC™ pump switch (sold separately).

(2) Sump Advisor™ Sensor

The sensor attaches on top of the VertiMAC™ VM-Series pump

switch and connects to the Sump Advisor™ alarm panel.

ADDITIONAL OPTIONS:

The standard product will include: (1) Sump Advisor™ 2-Zone Alarm Panel and (1) Sump Advisor™ Sensor.

(120VAC Piggyback Plug Model Shown)

(3) VertiMAC™ Pump Switch, VM-Series

The VertiMAC™ is a oat operated pump switch for sump pump

applications, includes a pipe clamp bracket and stainless steel

pipe clamp. The power cable is available in 120/240VAC bare

lead (no plug), 120VAC piggyback plug, or 240VAC piggyback

plug models. Rated 13 Amps.

(4) Indoor/Outdoor LED Strobe Beacon

The remote strobe beacon is connected to the Sump Advisor™

alarm panel and provides a secondary indoor or outdoor high

level alarm indication.

(5) Auto Dialer

The auto dialer is connected to the alarm auxiliary dry contacts

on the Sump Advisor™ alarm panel to monitor high level alarm

status. When the contacts close on the alarm panel, it activates

the input of the auto dialer sending a voice message to

programmed number(s).

Alderon Industries™ - Leading Edge Control Products | 5

Sump Advisor™ 2-Zone Alarm and Sensor - USER GUIDE

Features

Refer to the illustration below to reference the feature descriptions provided.

(1) Power On LED - A green LED illuminates on the front of the

alarm panel to indicate the power is on.

(2) High Sump LED - During an alarm condition, the red high

sump alarm LED will illuminate on the front of the alarm panel.

(3) Pump Run LED - When the pump switch activates the pump,

the green LED will illuminate on the front of the alarm panel for

pump run indication.

(4) Alarm Buzzer - The alarm buzzer will annunciate in addition

to the visual indication provided by the red LED during an alarm

condition.

(5) Alarm Test Pushbutton - Press the pushbutton to test the

alarm to ensure proper operation. The buzzer should annunciate,

high sump alarm LED should illuminate, and auxiliary contacts

should activate.

(6) Alarm Silence Pushbutton - Press the pushbutton to silence

the buzzer during an alarm condition. The alarm LED remains

illuminated until the alarm condition has been cleared and the

alarm panel will auto reset for the next alarm cycle.

(7) Terminal Block - Connect the Sump Advisor™ sensor to the

alarm panel for local high level alarm and pump run indication.

(8) Auxiliary Contacts - Interface with an external device

including building automation systems and phone dialers. The

contacts (normally open) are rated 24VDC/24VAC, 50/60 Hz, and

100mA maximum.

(9) Battery Backup - Install a 9VDC battery (not included) for

battery backup during power outages.

(10) Panel Compartment - Wire connector for 9VDC battery

(backup power), auxiliary dry contacts, and access cover with

break away tabs for routing wire.

(11) Power Supply (not shown) - A 120VAC, 60 Hz, 5-foot power

cord connects to a standard wall outlet.

(12) Mounting Holes - Two mounting holes are included on the

alarm panel enclosure to securely fasten in the desired mounting

location.

(13) Sensor Housing - Internal signaling components are

protected within housing to ensure a waterproof sensor.

(14) Sensor Cable - The cable sends a signal from the sensor to

the alarm panel. Rated 24VDC, 100mA maximum, 22 AWG, and

3-conductor.

(15) Mounting Tabs - Three tabs are located on the bottom of the

sensor housing to attach and secure the sensor to the top of the

VertiMAC™ pump switch.

(16) Float Basket - Houses the high level oat and protects from

obstructions in the monitoring area.

(17) Float - Rises and lowers inside the oat basket based on the

liquid level in the monitoring area.

(18) Locking Tabs (not shown) - Two tabs are located on the

bottom of the sensor housing which secures the oat basket in

place.

5 6

6 | Alderon Industries™ - Leading Edge Control Products

Sump Advisor™ 2-Zone Alarm and Sensor - USER GUIDE

Installation of Sump Advisor™ Alarm Panel

DISCONNECT ALL POWER SOURCES WHEN INSTALLING OR SERVICING THIS PRODUCT. FAILURE TO

TURN OFF ALL POWER SOURCES COULD RESULT IN SERIOUS INJURY OR DEATH.

ALARM PANEL MUST BE MOUNTED INDOORS. FOR OUTDOOR APPLICATIONS CONSULT FACTORY.

9VDC Battery Backup

STEP 1: REMOVE ACCESS COVER

To install or replace the battery for the backup power feature, remove the alarm panel access cover.

STEP 2: INSTALL/REPLACE BATTERY

Install the 9VDC battery matching the terminals of the wire connector on the alarm panel to the terminals on top of the battery.

Place the battery inside the top panel compartment to secure and ensure proper operation of the backup power feature.

Alderon Industries™ - Leading Edge Control Products | 7

Sump Advisor™ 2-Zone Alarm and Sensor - USER GUIDE

STEP 3: TEST INSTALLATION

After proper installation of the battery, the green power LED

should illuminate to indicate the alarm panel is powered on. If

the green LED does not illuminate, the battery was not properly

installed. Check connection before proceeding.

Press and hold the alarm test pushbutton to activate the alarm

function. The buzzer should annunciate and the red high sump

LED should illuminate.

9VDC Battery Backup (continued)

STEP 4: REPLACE ACCESS COVER

After the alarm panel battery backup power feature has been tested and determined to be working properly, replace the access

cover if the auxiliary dry contacts are not used. If connecting wires to the auxiliary dry contacts, leave the access cover off until

step 1 on page 9 is completed.

Power

Alarm

Test

Alarm

Silence

High

Sump

Pump

Run

8 | Alderon Industries™ - Leading Edge Control Products

Sump Advisor™ 2-Zone Alarm and Sensor - USER GUIDE

Mounting Alarm Panel

STEP 1: DETERMINE MOUNTING LOCATION

Determine the mounting location for the alarm panel, make sure the power outlet (120VAC, 50/60 Hz) is within ve feet (5′) of the

alarm panel. The power outlet should be on a separate circuit breaker from any other device and not on a switched receptacle

to maintain power integrity.

CAUTION: Do not connect power to the alarm panel until the installation of both the Sump Advisor™ alarm panel and Sump

Advisor™ sensor are completed.

STEP 2: MOUNT ALARM PANEL

Hold the alarm panel in the desired mounting location, mark the

drill hole locations. Once marked, drill pilot holes for screws (not

included) and use wall mount anchors (not included) if necessary.

Place alarm panel in the mounting location, adjust until the pilot

holes are lined up with the enclosure and fasten screws to secure

the alarm panel in place.

5 Feet Maximum

Alderon Industries™ - Leading Edge Control Products | 9

Sump Advisor™ 2-Zone Alarm and Sensor - USER GUIDE

Wiring Auxiliary Dry Contacts

STEP 1: TERMINAL BLOCK CONNECTIONS

If connecting to an existing alarm security system or building automation system (BAS), leave the positive (+) and negative (-)

terminals open and use 18 gauge 2-conductor wire to connect the existing product to terminals 2A, 2B, 1A, and 1B.

If connecting to an Alderon™ auto dialer using the supplied 4-conductor wire: connect red wire to positive (+) terminal, black

wire to negative (-) terminal, yellow wire to terminal 1A, and white wire to terminal 1B.

When the VertiMAC™ pump switch is activated, it will turn the pump on closing the pump auxiliary dry contacts 2A and 2B on

the Sump Advisor™ alarm panel. When the Sump Advisor™ sensor high level alarm oat is activated, it will close the alarm

auxiliary dry contacts 1A and 1B on the Sump Advisor™ alarm panel. See step 2 below for removing access cover break away

tabs and step 3 on page 10 for replacing access cover of the alarm panel after wiring for the auxiliary dry contacts is completed.

2A 2B 1A 1B

AUXILIARY DRY CONTACTS:

Terminals “+” (positive) and “-” (negative)

11.1VDC, 100mA power supply for external equipment

Terminals 2A and 2B

Zone 2 (Pump Run)

Normally Open

Terminals 1A and 1B

Zone 1 (High Sump)

Normally Open

Class 2, 24VDC/VAC (50/60 Hz)

100 Milliamps Maximum

Note: The auxiliary dry contacts of the alarm panel

are normally open ONLY.

STEP 2: REMOVING ACCESS COVER BREAK AWAY TABS

After the access cover has been removed from the alarm panel,

use a needle nose pliers (not included) to remove the desired

break away tab(s) from the access cover. Lightly pull and twist

off tab(s).

21 3

10 | Alderon Industries™ - Leading Edge Control Products

Sump Advisor™ 2-Zone Alarm and Sensor - USER GUIDE

STEP 3: REPLACE ACCESS COVER

After the wiring is completed and the desired break away tab(s) have been removed, replace the access cover and run wire(s)

through the knockout(s). Route all wires away from sharp objects and internal components when replacing the access cover.

Wiring Auxiliary Dry Contacts (continued)

Wiring Sump Advisor™ Sensor to Sump Advisor™ Alarm Panel

STEP 1: SUMP SENSOR WIRE CONNECTIONS

Connect the normally open Sump Advisor™ sensor (rated 24VDC, 100mA maximum) to the Sump Advisor™ alarm panel for local

high level alarm and pump run indication from the VertiMAC™ pump switch. Connect white wire to terminal W, red wire to terminal

R, and black wire to terminal B.

Installation of Sump Advisor™ Sensor

DISCONNECT ALL POWER SOURCES WHEN INSTALLING OR SERVICING THIS PRODUCT. FAILURE TO

TURN OFF ALL POWER SOURCES COULD RESULT IN SERIOUS INJURY OR DEATH.

WRB

TERMINAL BLOCK CONNECTIONS:

Sensor Wire Alarm Panel Terminal

White W = Common

Red R = High Level Alarm

Black B = Pump Run

White

Red

Black

Otros manuales para Sump Advisor 2000514

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema de seguridad de Alderon Industries

Alderon Industries

Alderon Industries Oil Alert VA02 Manual de usuario

Alderon Industries

Alderon Industries Vizzyalarm VZW-01 Manual de usuario

Alderon Industries

Alderon Industries Sump Advisor 2000514 Manual de usuario

Alderon Industries

Alderon Industries Wireless Versa'larm VA01B Manual de usuario

Alderon Industries

Alderon Industries VersAlarm I/O Manual de usuario

Alderon Industries

Alderon Industries VersAlarm I/O VLIO-0002 Manual de usuario

Alderon Industries

Alderon Industries Versa'larm VA01A Manual de usuario

Alderon Industries

Alderon Industries Versa'larm VA01D Manual de usuario

Alderon Industries

Alderon Industries Vizzyalarm VZW-02 Manual de usuario

Alderon Industries

Alderon Industries 8059 Manual de usuario

Alderon Industries

Alderon Industries Versa'larm VA02B Manual de usuario

Alderon Industries

Alderon Industries 7001 Versa’larm Manual de usuario

Alderon Industries

Alderon Industries VersAlarm 4X Manual de usuario

Alderon Industries

Alderon Industries VersAlarm I/O VLIO-00005 Manual de usuario

Alderon Industries

Alderon Industries VersAlarm VLIO-0004 Manual de usuario

Alderon Industries

Alderon Industries WaterPro WaterSpotter AVFD Series Manual de usuario

Alderon Industries

Alderon Industries Power Post VA-02 Manual de usuario

Alderon Industries

Alderon Industries Versa'larm 8124 Manual de usuario

Alderon Industries

Alderon Industries Versa'larm VA02A Manual de usuario

Alderon Industries

Alderon Industries Versa'larm 4X Manual de usuario

Alderon Industries

Alderon Industries Oil Alert VA03 Manual de usuario

Alderon Industries

Alderon Industries VersAlarm I/O VLIO-0001 Manual de usuario

Alderon Industries

Alderon Industries VersAlarm I/O VLIO-00005 Manual de usuario

Alderon Industries

Alderon Industries VersAlarm 4X Manual de usuario

Manuales populares de Sistema de seguridad de otras marcas

Inner Range

Inner Range Concept 2000 Manual de usuario

Climax

Climax Mobile Lite R32 Instrucciones de montaje

CADDX

CADDX NX-6 Manual de usuario

FBII

FBII XL-31 Series Manual de usuario

Johnson Controls

Johnson Controls PENN Connected PC10 Manual de usuario

Aeotec

Aeotec Siren Gen5 Manual de usuario

Blaupunkt

Blaupunkt SA 2700 Manual de usuario

IDEAL

IDEAL Accenta Manual del propietario

AJAX

AJAX DoubleButton Manual de usuario

Swann

Swann SW-P-MC2 Manual de usuario

Ecolink

Ecolink Siren+Chime Manual de usuario

Digital Monitoring Products

Digital Monitoring Products XR150 Manual de usuario

EDM

EDM Solution 6+6 Wireless-AE Manual de usuario

Highway Safety Group

Highway Safety Group EA401 Manual de usuario

Siren

Siren LED GSM Manual de usuario

Detection Systems

Detection Systems 7090i Instrucciones de montaje

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manual de usuario

Siemens

Siemens FDM273 Manual de usuario