Aktakom ??M-1130 Manual de usuario

AMM-1130

USER`S MANUAL

www.tmatlantic.com

АМM-1130

Contents

Chapter 1 Safety Information

◎Meter Safety Standards………………………………………………………………………………………………….

◎Warning………………………………………………………………………………………………………………….

◎Limited Guarantee and the Liability Range……………………………………………………………………………..

Chapter 2 Introduction to the Meter

◎Characteristics………………………………………………………………………………………….……………..…

◎Explanation on Front Panel……………………………………………………………………………………………...

◎Understanding Display Screen…………………………………………………………………………………………..

◎Function Descriptions……………………………………………………………………………………..…………….

Chapter 3 Operation Methods

◎DCV Measurement………………………………………………………………………………………………….....…

◎ACV Measurement………………………………………………………………………………………………………

◎DC mV/AC mV Measurement………………………………………………………………………………………….

◎Logic Frequency/Duty Ratio Measurement……………………………………………………………….…………….

◎Resistance/continuity/ Diode Measurement……………………………………………………………………………..

◎Capacitance Measurement……………………………………………………………………………………………….

◎Temperature Measurement………………………………………………………………………………………………

◎DCμA /ACμA Measurement…………………………………………………………………………………………

АМM-1130

◎DC mA/AC mA Measurement………………………………………………………….………………………………

◎DC Ampere/AC Ampere Measurement………………………………………………….…………………………….

◎Linear Frequency Measurement……………………………………….…………….……………….………..…………

◎Relative Value Measurement………………………………………………………….…………………………………

◎Maximum Value/Minimum Value Measurement……………………………………………………………….………

◎PEAK max/min measurement……………………………………………………………………………… ….… …….

◎Backlight Control……………………………………………………………………………………………….……….

◎Data Hold………………………………………………………………………………………………………………..

◎Automatic Shutdown and Continuous Operation Mode Selection………………………………………………………

◎Connected to USB Interface Of Computer………………………………………………………………………………

Chapter 4 Technological Specifications

◎General Features…………………………………………………………………………………………………………

◎Range and Accuracy……………………………………………………………………………………………………..

Chapter 5 Maintenance

◎Replacement of Batteries………………………………………………………………………………………………..

◎Replacement of Fuse…………………………………………………………………………………………………….

◎Others ………………………………………………………………………….………..………………………………

АМM-1130

Chapter 1 Safety Information

Meter Safety Standards

This style of digital multimeter is designed and manufactured according to the safety requirements set out by the IEC1010-1

standards for electronic test instruments and the hand-hold digital multimeters. Its design and manufacture is strictly based on

the provisions in the 1000V CAT II of IEC1010-1 and the Stipulation of 2-Pollution Grade.

The meter conforms to the European Union’s following requirements: 89/336/EEC

(EMC Electromagnetic Compatibility), 73/23/EEC (LVD Low Voltage Protection) and 93/68/EEC(CE Mark).

Warning

Before using the meter firstly checkup if there is any crack on the outer shell or if it lacks any plastic part, and checkup

whether the testing line is damaged or has any exposed metal. The meter can be used only if no any insulating problem be

found.

Carefully read the operating methods and safety prompts in this manual. Using it not based on the methods specified in

this manual may cause damage of the meter.

Don’t use the Non-normal meter. You should have it repaired.

Don’t use it in the environment with combustible gases, steam or dust pollution.

Measure carefully when the voltage is higher than 30VAC (effective value)or 50VDC for such voltage having the risk of

shock. Avoid the body directly touching ground or any metal substance in which there may be ground

АМM-1130

potential during measuring. Keep the body should be kept insulated from ground with dry insulating shoes, insulating pads

or insulating clothes.

When measurement with a test probe your fingers should be put behind a finger-protector.

Don’t try to measure a voltage higher than 1000VAC or 1000VDC, the meter may be damaged and the operator’s safety

may be threatened if the limit for voltage measurement is exceeded.

When the symbol of electric insufficiency appearing on the display screen it is necessary to replace the batteries for

avoiding the possible shock or injure resulted in by erroneous reading.

In case of replacing batteries, it is necessary firstly to pull out the testing line. AAA batteries should be used and they

should be put into the meter with the proper polarity.

Don’t make any voltage measurement when the testing line being inserting into the current hole.

The repair and calibration of the meter must be carried out by experienced professionals, others should not repair and

calibrate the meter by themselves.

Limited Guarantee and the Liability Scope

The company will undertake to repair freely any quality problem of the meter within 18 months from the date when it was

bought, except for the replacement of fuse and batteries as well as any damage caused by negligence, wrong use, pollution,

change of circuit and non-normal use.

Please offer the invoice before maintenance. for the maintenance beyond the 18-month guarantee period, the company will

charge some repair fee and materials cost.

АМM-1130

Chapter 2 Introduction to the Meter

Characteristics

22000 counts measurement

ACV and DCV measurements reach up to 1000V.

DC measurement accuracy reaches up to 0.05%.

0.01 Ω resistance resolution and 10μV voltage resolution.

Linear frequency measurement, logic frequency/duty ratio measurement.

Capacitance measurement from 0.001nF to 220mF.

AC true RMS measurement.

Temperature Measurement.

Maximum value/minimum value measurement, Relative measurement, PEAKmax/min measurement.

46-segment analog bar display.

Automatic shutdown/continuous working mode selection.

Back light control.

PC-LINK: USB infrared interface.

Display, record and graphics software of computer.

Overload protection.

Sound alarm for wrong current measurement.

Secondary plasticizing meter shell, with insulating performance reaching 1000V CAT II

АМM-1130

Explanation on Front Panel

The front panel is shown as in Figure 2-1,

explanation being as follows:

Figure 2-1

АМM-1130

(1) V/Ω/

℃

/CAP/DIODE/Hz end

It is the input end for all measurement functions except for current measurement, connected with a red meter probe.

(2) COM end

It is the negative input end for all measurements, connected with a black meter probe.

(3)µA/mA end

It is the positive end for measurement of µA or mA current, connected with a red meter probe.

(4)A end

It is the positive input end for measurement of 0.22A-10A current, connected with a red meter probe.

(5)Rotary switch

Used for selecting measurement functions such as Power off, voltage, current, resistance, temperature and Capacitance.

(6)PC-link switch

Used for connect PC for record the measurement value.

(7)PEAK-H key

Used for measuring PEAK-max, PEAK-min when input AC signal.

(8)HOLD key

Used to maintain the measurement data unchanging, by pressing the key again it will resume the measurement. Pressing this

key and last for 2 seconds, the meter will delay for 6 seconds, than enters HOLD mode.

АМM-1130

(9) FUNC. key

When setting the rotary switch to a measurement function, the meter will enter its first measurement mode, while pressing the

FUNC. key it is possible to select the second or the third measurement mode. However, there is only one for the Frequency and

Capacitance measurements.

(10)RANGE key

For various kinds of measurements it is used manually to select range. Under the automatic range state (AUTO displaying), it

will enter manual range state(MANUAL displaying) with a press on RANGE, after that the range will be changed with a press

on RANGE while the small digits on the left lower corner indicating the actual range. When the RANGE key being released

after pressing for one second the meter will return back to the automatic state.

(11) Hz/DUTY key

During the AC voltage or AC current measurements, by pressing Hz/DUTY key the meter will enter the linear frequency

measurement state. At this time what being measured is the frequency of voltage or current. By pressing this key again it will

enter the DUTY Cycle measurement state ,by pressing this key again it will return the voltage or current measurement state.

But if it during the Frequency measurements state, by pressing HZ/DUTY key the merer will enter DUTY Cycle measurement

state, pressing again it will be returned.

(12)LIGHT key

By pressing this key for a time, the backlight of the LCD screen will be opened and after 60 seconds the meter will

automatically turn off the backlight. It is also possible to turn off the backlight by pressing the LIGHT key before the 60

seconds.

АМM-1130

(13)REL key

By pressing REL to enter the relative measurement state, the meter will remember the value measured at the time when

pressing the key (it is called the initial value), and after that the value displayed in the meter will be equivalent to the present

value minus the initial value. By pressing the key again the relative measurement state will be exited. Pressing the key will be

void during the frequency and diode measurements.

(14)MAX/MIN key

Press MAX/MIN key to enter the record state for the maximum and minimum value and simultaneously display the maximum

value. When this key is pressed again, the meter displays the minimum value. When this key is pressed for the third time, the

current value will be displayed. When releasing the key after pressing it for one second, the maximum and minimum record

state will be exited. Pressing this key will be void during frequency and diode measurement.

(15)LCD screen

Used for displaying the measuring results and various symbols.

Understanding Display Screen:

LCD screen is shown as in Figure 2-2,

with its every symbol’s meaning shown as in the Table 1:

Figure 2-2:

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Multímetro de Aktakom

Aktakom

Aktakom AMM-1048 Manual de usuario

Aktakom

Aktakom AMM-1009 Manual de usuario

Aktakom

Aktakom AM-1083 Manual de usuario

Aktakom

Aktakom AM-1108 Manual de usuario

Aktakom

Aktakom AMM-1028 Manual de usuario

Aktakom

Aktakom ABM-4083 Manual de usuario

Aktakom

Aktakom AM-1060 Manual de usuario

Aktakom

Aktakom AM-1142 Manual de usuario

Aktakom

Aktakom ABM-4082 Manual de usuario

Aktakom

Aktakom AMM-1022 Manual de usuario

Aktakom

Aktakom AM-1016 Manual de usuario

Aktakom

Aktakom AMM-1032 Manual de usuario

Aktakom

Aktakom AM-1171 Manual de usuario

Aktakom

Aktakom ACM-2353 Manual de usuario

Aktakom

Aktakom AMM-1008 Manual de usuario

Aktakom

Aktakom AMM-1081 Manual de usuario

Manuales populares de Multímetro de otras marcas

Agilent Technologies

Agilent Technologies 34420A Manual de usuario

Fluke

Fluke 83 Manual de usuario

Hameg

Hameg HM 8012 Manual de usuario

Mastech

Mastech MY70 Manual de usuario

Steren

Steren MUL-300 Manual de usuario

Somogyi Elektronic

Somogyi Elektronic home SMA 92 Manual de usuario

Gossen MetraWatt

Gossen MetraWatt METRAmax 6 Manual de usuario

PeakTech

PeakTech 4000 Manual de uso y cuidado

YOKOGAWA

YOKOGAWA 90050B Manual de usuario

Gossen MetraWatt

Gossen MetraWatt METRALINE DMM16 Manual de usuario

Fluke

Fluke 8846A Manual de operación y mantenimiento

Tempo Communications

Tempo Communications MM200 Manual de usuario

Elenco Electronics

Elenco Electronics CM-1555 Manual de usuario

Mastech

Mastech MS8238C Manual de usuario

SDAR

SDAR 830A, 830B, 830D, 830C Manual de usuario

RS PRO

RS PRO RS-9519BT Manual de usuario

BGS technic

BGS technic 8890 Manual de usuario

Amprobe

Amprobe Hexagon 60 Manual de usuario