AkitikA GT-101 STEREO Manual de usuario

Page 1 of 44

GT-101 STEREO

AUDIO POWER AMPLIFIER

ASSEMBLY MANUAL

Revision 1p37 Octo er 29, 2013

Page 2 of 44

Table of Contents

Ta le of Contents................................................................................................................ 2

Ta le of Figures .................................................................................................................. 3

Section 1: A out This Manual ............................................................................................ 4

Who Should Attempt this Project? ................................................................................. 4

Tools You’ll Need........................................................................................................... 4

Project Overview ............................................................................................................ 5

Important Safety Notes ................................................................................................... 5

A out Components ......................................................................................................... 5

Recommended Solder ..................................................................................................... 5

Warranty ......................................................................................................................... 5

Section 2: Building the Power Supply PCB ....................................................................... 6

Component Order............................................................................................................ 6

Install the Resistors ......................................................................................................... 6

Install the Diodes ............................................................................................................ 8

Identifying the glass ody diodes ............................................................................... 8

Install the Last Resistor................................................................................................. 10

Install the Small Capacitors .......................................................................................... 10

Install the Integrated Circuits........................................................................................ 11

Install the Transistors.................................................................................................... 11

Install the Big Capacitors.............................................................................................. 11

Final Inspection of the Circuit Board............................................................................ 12

Power Supply Final Assem ly...................................................................................... 12

Section 3: Assem ling the Amplifier Circuit Boards ....................................................... 14

Install the Resistors ....................................................................................................... 15

Install the Small Capacitors and the Diodes ................................................................. 17

Last Capacitors and the Transistors .............................................................................. 18

Winding the Output Inductor ........................................................................................ 19

Final Inspection of the Circuit Board............................................................................ 20

Installing the LM3866 and Mounting the Amplifier Board to the Heat Sink............... 21

Section 4: Wiring it All Together ..................................................................................... 23

Attach the Power Supply Ground Wire ........................................................................ 23

Attach the Amplifier Module Wires ............................................................................. 23

Attaching LEFT Module Wires ................................................................................ 23

Attaching RIGHT Module Wires.............................................................................. 24

Build the Ground Harnesses ......................................................................................... 25

Install the Feet............................................................................................................... 26

Install the Speaker Binding Posts ................................................................................. 27

AC Power Wiring ......................................................................................................... 27

Installing Amplifier Modules into the Chassis ......................................................... 29

Transformer Preparation ........................................................................................... 31

Transformer Installation............................................................................................ 33

Testing the Power Supply ............................................................................................. 34

Final Amplifier Wiring ................................................................................................. 35

Wiring Amplifier Power ........................................................................................... 35

Page 3 of 44

Fasten the Power Supply to the Chassis ................................................................... 35

Visual Inspection ...................................................................................................... 36

Install the Shield ....................................................................................................... 36

Section 5: Testing It Out and Installing the Top............................................................... 37

Install the Top ........................................................................................................... 37

Section 6: Using the GT-101 ............................................................................................ 37

Section 7: Specifications and Schematics......................................................................... 38

Appendix 1 - Resistor Color Code................................................................................ 42

Appendix 2 - Preparing a Shielded Ca le End ............................................................. 43

Table of Figures

Figure 1-Component side of power supply PCB efore loading........................................ 6

Figure 2-Installing resistors ................................................................................................ 7

Figure 3-R11 location (PCB's are missing the silk screen for R11) ................................... 8

Figure 4-Form the cathodes of D4-D7 as shown ( anded end denotes cathode) ............. 10

Figure 5-Pinout of U1, viewed from the top..................................................................... 11

Figure 6-Note the rounded rackets used for the power supply heatsink and PCB ......... 12

Figure 7-Placing thermal compound on Q5...................................................................... 13

Figure 8-Installing Q5 on the heatsink and to the PCB .................................................... 13

Figure 9-Remem er to solder Q5's leads.......................................................................... 13

Figure 10-Assem led Power supply mounted on heat sink.............................................. 14

Figure 11-Empty the amplifier components into a soup owl.......................................... 14

Figure 12-Closeup of Completed Amplifier oard........................................................... 15

Figure 13-First four resistors are installed, leads ent on the ack side, soldered, then

clipped............................................................................................................................... 15

Figure 14-Zero Ohm R22 installation detail..................................................................... 17

Figure 15-showing LED cathode orientation.................................................................... 18

Figure 16-Starting to wind the output inductor................................................................. 20

Figure 17-finishing step for the output inductor ............................................................... 20

Figure 18-Mounting assem led PCB to heat sink ............................................................ 21

Figure 19-mounting the PCB to the heat sink................................................................... 21

Figure 20-a completed amplifier module.......................................................................... 22

Figure 21-solder the LM3886 pins ................................................................................... 22

Figure 22-from left to right, #6 lug, #10 lug, RCA connector ground lug ....................... 23

Figure 23-power supply with attached ground wire ......................................................... 23

Figure 24-shielded ca le for left channel. Right channel has overall length of 10 inches.

........................................................................................................................................... 24

Figure 25-Left Channel Grounding Harness (some lengths differ from the right channel)

........................................................................................................................................... 25

Figure 26-Right Channel Grounding Harness (some lengths differ from the left channel)

........................................................................................................................................... 26

Figure 27-Install the feet here ........................................................................................... 26

Figure 28-Install oth left and right inding posts (only right channel is shown here).... 27

Figure 29-FASTON connector ......................................................................................... 27

Figure 30-Wiring IEC power connector ........................................................................... 28

Figure 31-Power wiring with IEC connector installed into chassis.................................. 28

Page 4 of 44

Figure 32-Installing power wires on the switch................................................................ 29

Figure 33-I/O Connector wiring ....................................................................................... 30

Figure 34-spread thermal compound on the 3/8" wide ridge............................................ 30

Figure 35-amps installed, wiring not complete................................................................. 31

Figure 36-Wiring toroidal transformer for 120 Volt operation ........................................ 31

Figure 37-Western Union splice has diameter less than the insulated wires and no sharp

points................................................................................................................................. 32

Figure 38-Toroidal Transformer Mounting ...................................................................... 33

Figure 39-connecting up the power transformer............................................................... 33

Figure 40-ca le tie the red and orange wires as shown .................................................... 34

Figure 41-Grounding Stud Detail ..................................................................................... 36

Figure 42-Shield Installation............................................................................................. 36

Figure 43-Power Supply Schematic.................................................................................. 39

Figure 44-Amplifier Module Schematic........................................................................... 40

Figure 45-Overall Wiring (powering transformer is wired for 120 VAC) ....................... 41

Figure 46-demonstrating the resistor color code .............................................................. 42

Figure 47-Shield wired end prep completed..................................................................... 44

Section 1: About This Manual

This manual gives the information needed to uild Akitika LLC’s GT-101 Stereo Power

Amplifier.

Who Should Attempt this Project?

You can uild this kit if you can:

1. solder (using normal rosin core solder and a soldering iron).

2. use simple hand tools like screwdrivers, wire cutters, and pliers.

3. read and follow directions.

It helps if you:

1. know a it a out electronics, or

2. have a friend who knows a it a out electronics

3. can get to YouTu e to watch a few helpful videos a out the assem ly process

Tools You’ll Need

You’ll need the following tools:

1. Phillips screwdriver (#1 and #2)

2. pliers or nut drivers suita le for #6 hardware (5/16” nut driver or hex wrench).

Note that the 5/16” nut driver is also the correct size for the speaker inding post

nuts.

3. needle nose pliers (helpful, ut not strictly necessary)

4. pencil type soldering iron of 25 to 50 Watts (no huge honking soldering guns or

lowtorches)

5. wire cutters and strippers

6. multi-meter (helpful, ut not strictly necessary)

7. magnifying glass, if you’re over 42!

Page 5 of 44

Project Overview

The project consists of the following steps:

1. Build the Power Supply Regulator Board

2. Build left and right channel amplifier circuit oards.

3. Install and wire the circuit oards, switches, and connectors into the chassis.

Important Safet Notes

By purchasing, using, or assem ling this kit, you have agreed to hold AkitikA, LLC

harmless for any injuries you may receive in its assem ly and/or use. To prevent injuries:

• Wear safety glasses when soldering to prevent eye injuries.

• Always unplug the power efore working on the amplifier.

• Large capacitors hold lots of energy for a long time. Before you put your hands

into the amplifier:

o Pull the AC plug!

o Wait 2 full minutes for the capacitors to discharge!

• Remove jewelry and rings from your hands and wrists, or anything that might

dangle into the amplifier.

• If working in the amplifier, keep one hand in your pocket, especially if you’re

near the power supply or power supply wires. This can prevent serious shocks.

• Build with a uddy near y. If you’ve ignored all the previous advice, they can

dial 911 or get you to the hospital.

About Components

We reserve the right to make design/or component changes at any time without prior

notification.

Recommended Solder

The kit must e assem led with 60/40 Rosin Core solder. The recommended diameter is

0.032 inches. Among many such sources of solder, I have used Radio Shack part num er

64-009. It contains 8 oz. of solder, which is much more than you’ll need to assem le the

GT-101 kit.

Warrant

With the exception of fuses, Akitika will replace for free any parts of a correctly

assem led GT-101 that fail within one year of the date of purchase when the amplifier

has een used in home stereo applications. It is the responsi ility of the kit uilder to

install the replacement part(s). This warranty applies to the original purchaser only. It

does not apply to units that have een physically or electrically a used, modified without

prior factory authorization, or assem led with other than 60/40 Rosin Core solder.

Akitika LLC’s lia ility shall in no event exceed the cost paid to Akitika LLC for the kit.

Page 6 of 44

Section 2: Building the Power Supply PCB

This section details the process of uilding the power supply circuit oard. We start with

an overview on this page. The specifics you need to start uilding egin on the next page.

The are power supply PCB is shown in Figure 1.

Figure 1-Component side of power supply PCB before loading

Begin y carefully emptying the contents of the envelope marked “GT-101 PSU Module”

into a road soup owl, as shown elow. In general, you’ll start with the components that

lay closest to the oard, working your way towards the taller components. You will:

1. Install the resistors (all ut one

power resistor, left for later)

2. Install the diodes

3. Install the capacitors

4. Install the integrated circuits.

5. Install the transistors

6. Install the pass transistor Q5 as you

mount the PCB to the heat sink.

Component Order

You’ll notice that the component designations in the directions don’t go exactly in order.

We have grouped them so that all components with the same value appear together. This

makes assem ly easier. You’ll find in the parts kit that similar parts, e.g. 3 1K resistors,

are typically (though not always) taped together.

Install the Resistors

In general, you install the resistors y placing the ody on silk screen side of the oard,

and the leads through the indicated holes. Bend the leads over on the ack of the oard to

keep the resistors from falling out until your solder them in place. Try to end the leads in

a direction that won’t lead to solder ridges etween traces that should remain

disconnected.

Page 7 of 44

Figure 2-Installing resistors

We recommend the following procedure:

1. Insert all the resistors of the same value, e.g. R2, R3 and R4.

2. Bend the leads as descri ed a ove.

3. Solder the leads on the ack of the oard.

4. Clip the leads.

Track your progress y placing a check-mark in the done column as you install each

resistor. Check resistor values with a meter, or y reading the color code

. Orient the

resistor with the fat rown and on the right, then you can read oth the Color Code

column and the resistor from left to right.

¼ Watt, 1% resistors

Designation

Value Color code Done? ()

R2 1K Brown, Black, Black, Brown, Brown

R3 1K Brown, Black, Black, Brown, Brown

R4 1K Brown, Black, Black, Brown, Brown

R6 10K Brown, Black, Black, Red, Brown

R26 10K Brown, Black, Black, Red, Brown

R27 10K Brown, Black, Black, Red, Brown

R8 20K Red, Black, Black, Red, Brown

R9 20K Red, Black, Black, Red, Brown

R1 15K Brown, Green, Black, Red, Brown

R5 140K Brown, Yellow, Black, Orange, Brown

R7 5K76 Green, Violet, Blue, Brown, Brown

R10 26K1 Red, Blue, Brown, Red, Brown

R11

3K48 Orange, Yellow, Gray, Brown, Brown

R13 3M01 Orange, Black, Brown, Yellow, Brown

R22 165K Brown, Blue, Green, Orange, Brown

R23 100 Brown, Black, Black, Black, Brown

R24 95K3 White, Green, Orange, Red, Brown

R25 This location remains empty

We will defer installation of R12, a 0.1 Ohm power resistor, for a it later in the assem ly

process.

See “Appendix 1 - Resistor Color Code” on page 42 to see how to read resistor color codes.

See next page for location of R11. The R11 designation is missing from the silk-screen.

Page 8 of 44

Figure 3-R11 location (PCB s are missing the silk screen for R11)

Install the Diodes

Now install the diodes. Be careful to o serve the polarity markings on the diodes. You’ll

notice that one end of the diodes has a and. That and indicates the cathode of the diode.

Match the anded end of the diode with the anded end of the silk screen. The following

information should help you identify the diodes.

dentifying the glass body diodes

The glass ody diodes have the following identifying marks. If your vision is like mine,

you may need good light and a magnifying glass.

• 1N4148, D8-D11, has the num er 48 visi le

• BZX55B33B, D1 and D14, has the num er 33 visi le

• BZX79-B10, D2, has the num er 10 visi le

Also, typically when these diodes are packed, you can preliminarily identify the types

ecause:

• The 4 1N4148 diodes will typically e taped together

• The 2 BZX55B33B diodes will typically e taped together

• The 1 BZX79-B10 diode will e y itself

Page 9 of 44

D4-D7, opaque

lack plastic

package

D12, D13,

package type

DO-41, opaque

lack plastic

package

D1, D2, D8-

D11, D14,

package type

DO-35, glass

package

Keep track of the diodes as you install them using the following ta le. Remem er to

watch the polarity of the diodes, matching the anded end of the diode to the anded end

of the silk screen.

Designation Type, Package Description Done? ()

D1 BZX55B33, DO-35 33 Volt 2% zener diode

D14 BZX55B33, DO-35 33 Volt 2% zener diode

D2 BZX79-B10, DO-35 10 Volt 2% zener diode

D8 1N4148, DO-35 0.2 A, 100 PIV, switching

diode

D9 1N4148, DO-35 0.2 A, 100 PIV, switching

diode

D10 1N4148, DO-35 0.2 A, 100 PIV, switching

diode

D11 1N4148, DO-35 0.2 A, 100 PIV, switching

diode

D12 1N4004, DO-41 1A, 400 PIV, rectifier

diode

D13 1N4004, DO-41 1A, 400 PIV, rectifier

diode

Warning: Don’t cut the leads of D4-D7 until after the leads have een formed and the

diodes have een soldered into the PCB.

Page 10 of 44

Form the leads of D4-D7 as shown in Figure 4. Solder one lead of each diode while

attempting to keep the ody perpendicular to the plane of the oard. Ideally, the anodes

of D4-D7 should sit a out 1/8” to 1/16” off the oard.

Figure 4-Form the cathodes of D4-D7 as shown (banded end denotes cathode)

Designation Type, Package Description Done? ()

D4 6A4, R-6 6A, 400 PIV, rectifier

diode

D5 6A4, R-6 6A, 400 PIV, rectifier

diode

D6 6A4, R-6 6A, 400 PIV, rectifier

diode

D7 6A4, R-6 6A, 400 PIV, rectifier

diode

Install the Last Resistor

R12 should e air-mounted, with the ottom of its ody a out 1/8” a ove the PCB.

2 Watt, 5% resistor

Designation

Value Marking Done? ()

R12 0.1 0.1

Install the Small Capacitors

Now install the small capacitors:

C1, C2, and C3 are polarized, showing a minus sign (-) on the negative end of the

capacitor. Ma e sure that the minus sign faces away from the plus sign (+) mar ed on

the sil screen for each of the capacitors.

Designation Value Description Done? ()

C1 10 µF 100V electrolytic (polarized), cylindrical

shape

C2 10 µF 100V electrolytic (polarized), cylindrical

shape

C3 10 µF 100V electrolytic (polarized), cylindrical

shape

C4 100 nF 50V, Z5U, +/- 20%, marked 104

C5 10 nF 400V, film, 20%, ox shaped

Tabla de contenidos

Otros manuales de Amplificador de AkitikA

Manuales populares de Amplificador de otras marcas

ASTRO

ASTRO HVO V40 P Manual de usuario

Marantz

Marantz SUPERSCOPE BLA-545 Instrucciones de montaje

NAD

NAD CI980 Manual de usuario

Technics

Technics SE-CH770 Manual de usuario

Harman Kardon

Harman Kardon HK6300 Manual de usuario

NAD

NAD T975 Manual de usuario

McIntosh

McIntosh MA6850 Manual de usuario

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manual de usuario

Viatron

Viatron Autrix Manual de usuario

GME

GME GA9800 Manual de usuario

Atlas

Atlas CP700 Manual de usuario

Roland

Roland KC-1000 Manual de usuario

Pyle

Pyle PFMRA350BW Manual de usuario

Advantage

Advantage S-250 Manual de usuario

IRT Electronics

IRT Electronics DVA-3007 Manual de usuario

Dimavery

Dimavery BA-100 Series Manual de usuario

Sony

Sony XM-S400D Manual de usuario

Schertler

Schertler ROY X Manual de usuario